R₂ (Ten-point surface roughness)Theand valleysmean#Waviness?error* Lay:of distance b/us five consecutivesampling length.over aIt vitlat relates to textureсеропroughness is superimposed.It ismainly caused because of the deflection b/wtoo and workpiece. It refers to irregularities which areoutside the roughnescut-off valuesForm:It is afeature of the surface whichis caused by thermal distortion (deflection orcompressibility of a material under temperature and pressure float)of tool & workpicain slideandсосу> Yield strengthmacroالامتحنelastic tostrength,yieldIt is theDATEPAGEwearand4+ represents the direction of predominantsurface pattern produced it reflectothe machining operation used to produce it.The magnitude of stress atfrompeaksmaximumwhichof stress at which the transitionplastic occurs is known aslimit of elastic behaviour.> Toughness: A material's ability to absorb energyand deform (elastically & plastically)without fracturing.

Answered: Image /qna-images/answer/16489ae5-33af-4056-9dbf-3b6c5a08b0a6.jpg

- Rz (Ten-point surface roughness, The mean and valleys of distance b/us five Over a Wavines: ·Lay: It outlet relates to texture серот roughness is superimposed. It is mainly caused because of the deflection b/w tood and workpiece. It refers to irregularities which are outside the roughness width cut-off values five consecutive simpeling length. macro Form: It is a feature of the surface which is caused by thermal distortion ( deflection compressibility of a material under temperature and госу of tool & workpies oy pressure flas error in slide and peaks which wear maximum 'It represents the direction of predominant surface pattern produced it reflects the machining operation used to produce and it. Yield strength The magnitude of stress at which the transition from elastic to elastic to plastic occurs is known as yield strength. It is the limit of elastic behaviour. Toughness: A material's ability to absorb energy and deform (elastically 4 plastically) without fracturing.

- Rz (Ten-point surface roughness, The mean and valleys of distance b/us five Over a Wavines: ·Lay: It outlet relates to texture серот roughness is superimposed. It is mainly caused because of the deflection b/w tood and workpiece. It refers to irregularities which are outside the roughness width cut-off values five consecutive simpeling length. macro Form: It is a feature of the surface which is caused by thermal distortion ( deflection compressibility of a material under temperature and госу of tool & workpies oy pressure flas error in slide and peaks which wear maximum 'It represents the direction of predominant surface pattern produced it reflects the machining operation used to produce and it. Yield strength The magnitude of stress at which the transition from elastic to elastic to plastic occurs is known as yield strength. It is the limit of elastic behaviour. Toughness: A material's ability to absorb energy and deform (elastically 4 plastically) without fracturing.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Test-II. Write down all the operations or step by step procedure on how to create the object below. Write down also the name of the machines and the tools that you will use to complete the drawing below. 824 020 015 22 15 35 40 100 NOTE: ALL DIMENSIONS ARE IN MM ALL CHAMFERS ARE 1X 45
Q1/B) Match between Column A & B. A 1 Cutting Fluids 2 HSS 3 Serrated or segmented chips 4 Vertical shaper 5 Milling 6 Chip load 7 continuous Chip with BUE 8 Slitting 9 Electron beam machining 10 Ultrasonic machining B Horizontal milling machining vibration E Ductile material machined at low cutting speed F Interrupted cutting operation G Emulsified Oils H Cyclical formation of alternating high shear strain followed by low shear strain 1 Slotter J Feed per cutter tooth A Good toughness vacuum B C D Answer from A
Refer to the figure below. What is the MMC, LMC and geometric tolerance for the Hole and Pin: a. Hole: MMC LMC Geom. Tol. b. Pin: MMC_ LMC Geom. Tol. C 1.000 1 1.000 Ø.515-.540 Hole +0.010M ABC 1.000 B Figure for Problem 21 Ø.495-.500 Pin +0.005MABC A
Given the following G-code, what is the width of the rectangle if a 1/2" end mill is in the tool holder? (assume (0,0,0) is at the lower left, and z=0 is set at the top surface of the workpiece as usual) G20 G90 G28 M06 T1 M03 S1000 GOO XO YO Z-.25 G41 D1 G01 X1 Y1 Z-.25 F3 G01 X5 Y1 Z-.25 F3 G01 X5 Y3 Z-.25 F3 G01 X1 Y1 Z-.25 F3 GO0 X4 YO Z.25 a) 3.5" b) 4.5" c) 3" d) 4" e) 5"
Show all working explaining detailly each step Answer must be typewritten with a computer keyboard! Answer Q7i, ii
! SHOW FULL SOLUTION ! *DRAW FBD PLS *use DATA GIVEN PROPERLY thank you!
Whats the formulae for temperature error %
pls put solut1on thank u0
answerDcorrectly.
Calculation of Limits using ANSI B4.1 Standard Tables, when one of the design Features Exists. When calculating the limit tolerances for features that mate with purchased parts, the purchased part size must be known. This may be obtained be requesting a drawing from a vendor or, a caliper or micrometer can be used to obtain an accurate size. A shaft diameter of 1.2500" is to be pressed into a part using a FN3 interference (force) fit. Limits of size for the shaft diameter are 1.2500" and 1.2495". Determine the Limits of the hole diameter. Show all work.
IL IOUJOICIICA RAGICated in the 2-Dirmensional views (Orthographic) is milimeters centimeters There is no way of teling meters 3. When yow stari investigating to salve technological problems the following Technologiool Process yes can be followed to find information: Compare exising products write o design brief perform practical tests both A and C plus collect data. 4.Jocolleci dota the folowing could be used as a resource: Sractical investigation and testing of oproduct A, Band C A speok to or inteniew people firnd infomclion irom any print medio 6. existing products will help technologists in 20
3. If the tolerance applies at MMC then a possible O indeterminant bonus O LMC zero tolerance exists.