SITUATION 3 A plate is lapped over and welded to a gusset plate as shown in the figure a. Calculate the Polar moment of Inertia of the weld group b. Determine the maximum force per unit millimeter of the weld due to the direct load c. Determine the maximum force per unit millimeter of the weld due to the moment induced by eccentrical load d. Calculate the Resultant force received by the most critical joint due to eccentric load P= 90 kN 100 mm 150 mm LOD mm 44 kli 150 mm 150 mm

SITUATION 3 A plate is lapped over and welded to a gusset plate as shown in the figure a. Calculate the Polar moment of Inertia of the weld group b. Determine the maximum force per unit millimeter of the weld due to the direct load c. Determine the maximum force per unit millimeter of the weld due to the moment induced by eccentrical load d. Calculate the Resultant force received by the most critical joint due to eccentric load P= 90 kN 100 mm 150 mm LOD mm 44 kli 150 mm 150 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

6 in . T F = 2,000 lbs 2-in dia. Given loads: For the specified loading case: • Calculate the force per inch of weld for each of the stress components: the vertical shear, the bending, and the torsion. Determine the combined resultant force per inch of weld. For the specified weld size, calculate the maximum combined shear stress in the weld throat. Answer: Tmax=25.6 psi T = 15,000 in-lbs | • Using the maximum allowable shear stress for A36 steel and a weld electrode of E70 (see Table in your textbook), calculate a new weld size for the same load conditions.
The figure shows a solid 2-inch diameter roller that is attached to the wall by means of a permanent clamping. Specify the weld size for the case where the maximum allowable shear stress is 18 kpsi.
4. A solid shaft was made of alloy steel, it was welded to a flat plate by a specific size of fillet weld. If a torque is applied to the shaft, calculate the size of the weld joint. Power Torque Yield stress Shear stress Ultimate stress (Mpa) Compression stress (Mpa) Ductility (%) (kw) (Nm) 1000 (Mpa) 400 (Mpa) 160 280 30 Modulus of Bending Stress Bending Moment Factor of Safety Elasticity (GPa) (Mpa) 220 280 120 4 Modulus of Rigidity (pa) 70 Fracture stress (Mpa) 250
PROBLEM-7 (HW):The weld at O can support a maximum of 2500 N of force along each of the n- and t-directions and a maximum of 1400 of moment. Determine the allowable range for the direction 0 of the 2700-N force applied at A. The angle 0 is restricted to 0 <0<90°. 0.7 m 2700 N
2. Calculate the shear stress in a simple pin joint, assuming pin diameter of 10 mm and 3550N compressive load on the link. Draw a free body diagram (geometry & forces) Identify stress plane Calculate stress and write it (with appropriate units) in the outlined box
3. Calculate the bearing stress and shear stress between the pin and each bracket of a clevis joint. Assume pin diameter of 10 mm, 40 mm wide gap link, 12 mm thick bracket, and 3550N tensile load. Draw a free body diagram (geometry & forces) Identify stress plane Calculate stress and write it (with appropriate units) in the outlined box
Figure 4: Determine the bar force at FN (Answer in whole number, indicate the answer in kN. just input the value, do this for all the questions on Figure 4) Note: if the member is in compression, write a negative symbol before it, ex: 12kn in compression is answer:-12
For the "C" shaped welded joint shown, the magnitude of force P that will result in a moment of 1540 lb.in will be: 10.00 in 4.00 in 6.00 in
The force P3 to make it to equilibrium in kN is The Stress in section 1 in N/mm2 is The Compressive Stress in section 2 in N/mm2 is The stress in section 3 in N/mm2 is The total change in length in x10-3 mm is
A circular shaft of diameter 120 mm is welded to a rigid plate by a fillet weld of size 6 mm. If a torque of 8 kNm is applied to the shaft, what is the maximum stress in the weld?
The connected pipes are attached to the wall with a fixed support; i.e. built in. Calculate the reaction forces due to the loading shown. FBD required, can be more sketch like, but must have all reactions drawn and labeled.The 150 N force is parallel to the z axis; −150 k', the 200 N force is parallel to the y axis; 200 j,̂I will assume that all of the moment support reactions(curved arrows) are drawn positive.
The cable carrying three 400-N loads has a sag at C of hC = 14 m. Calculate the following: 26.1 The magnitude of the tensile force in segment AB is Blank 1 N. 26.2 The magnitude of the tensile force in segment BC is Blank 2 N. 26.3 The magnitude of the tensile force in segment CD is Blank 3 N. 26.4 The magnitude of the tensile force in segment DE is Blank 4 N.