T(°C) V(mV) 8 10 14 12 16 18 22 20 24 Voltage values with respect to a temperature measurement via a K-type thermocouple is given in the above table. By performing a line fit (with least squares method) in the form of V=aT+b, estimate the values of sensitivity and offset of the thermocouple from the fitted line. O A) Sensitivity = 3 097. Offset = 1054 O B) Sensitivity = 0 547. Offset = -2 055 O C) Sensitvity = 1054, Offser 3 007 O DI Sensit vity = -2 065 Offse: = 0.547

T(°C) V(mV) 8 10 14 12 16 18 22 20 24 Voltage values with respect to a temperature measurement via a K-type thermocouple is given in the above table. By performing a line fit (with least squares method) in the form of V=aT+b, estimate the values of sensitivity and offset of the thermocouple from the fitted line. O A) Sensitivity = 3 097. Offset = 1054 O B) Sensitivity = 0 547. Offset = -2 055 O C) Sensitvity = 1054, Offser 3 007 O DI Sensit vity = -2 065 Offse: = 0.547

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter19: Special-purpose Outlets-water Pump, Water Heater

Section19.2: Water Heater Branch Circuit

Problem 8R: For residential water heaters, the Consumer Product Safety Commission suggests a maximum temperature...

See similar textbooks

Similar questions

For residential water heaters, the Consumer Product Safety Commission suggests a maximum temperature setting of ___________ F (_____________ C). Some states have laws stating a maximum temperature setting of ____________ F (________________ C).
A single-phase half wave uncontrolled rectifier circuit is operating with a purely inductive load and a source voltage of 100 sin (277t) V. An ideal PMMC ammeter is connected in series with the inductive load reads 20 A. Calculate the distortion factor of the rectifier. Answer Choices: a. 0.866 b. 0.707 c. 0.577 d. 0.816
Z01 @ C Asiacell l. positive clipper negative cli 03_diode_clipper_clamper_multiplie... pi 5/12 7. Questions: A. The positive peak voltage of a positive clipper is: 1- 0 V 2- 0.6 V 3- Equal to the input peak voltage 4. 1.2 V B. Why is the positive peak voltage in the negative clipper not cut? 1- The diode is forward biased 2- The diode is reversed biased C. In a positive polarized clipper we found the voltage source in series to the diode equal to be +5V. Which is the cut level of the positive voltage? 1- 0.6 2- Equal to the input peak voltage 3- 5 V 4- 5.6 V 6/12
A Capacitor filter is used at the output across the load in order to minimize the ripple factor of the output voltage. The expressions of the average output voltage Vpc and the output AC component VAc are given below. If R = 1k2 and the single phase bridge rectifier supplied from a 120V - 50 Hz sinusoidal source, then the capacitor value that will maintain the amount of the output ripples to less than 4% would be equal to: VDC = Vm(4FRC – 1)/4ƒRC) VAC = Vm/(4/2ƒRC) Select one: O a. 63.39uF O b. 33.2uF O c. 93.39UF O d. 126.2uF TOSHIBA
A single phase – half wave controlled rectifier with freewheeling diode is supplying a load consistingseries connected a resistor and an inductance from a 70.7V (RMS), 50Hz sinusoidal AC source.The firing delay of the thyristor is 90° and the load values are R=10Ω, L=0.1 H. Define the loadcurrent expression and draw the load current by calculating for first two periods. And calculate theaverage values of the load voltage and current.
quations. 3. What are the advantages and disadvantages of a dual slope ADC? a blecL mation
Vps = 10 V R = 0.1k02 ww -ovo R₁. Consider the Zener diode circuit shown in figure. The Zener diode voltage is Vz= 5.8V at Iz= 10mA and the Zener resistance is rz = 200. a) Find the output voltage for RL = 1k0 b) Find the change in the output voltage when the load resistance varies +ARL.
Q1)Design moving coil ammeter as a voltmeter to read 15 V (RMS) alternating voltage. If the internal resistance of the ammeter is 5 K2, the voltage across the internal resistance is 0.5 v and the resistance of the diodes in the forward direction is 1 K2, find the multiplier resistance and sensitivity. Assume half wave rectification and a shunt resistance across the meter. The value of the shunt resistance across the ammeter is 2.5 KQ. Q2) Re-design the question above for full wave rectifier (without Rsh)
A full-wave rectifier is connected to a single-phase source and supplying an inductive load. For the sake of simplicity, you can assume that the ripple at the output current is negligible. Input specifications: The source is single-phase utility grid at 220 V and 50 Hz. Output specifications: The load resistance is 10 Ohm. Sketch the schematic of the system. Sketch the waveforms of the output voltage and current and the source voltage and current. Determine all the performance parameters.
The cut-in voltage for each diode in the circuits shown in Figure Pl.30 is V, = 0.6 V. For each circuit, determine the diode current I, and the voltage Vo (mea- sured with respect to ground potential). Q7 R= 10 k2 Vo oVo Ip R= 10 k2 5 V 5V 5 V 5 V (a) (b) R= 10 k2 Vo 5V E 5 V (c)
CIRCUIT DIAGRAM : D1 IÑ4001 AC Source RL 1K Q VOUT PROCEDURES : 1. Construct the half-wave rectifier circuit as shown. 2. Monitor the input voltage using the oscilloscope. Adjust the oscilloscope to show at least two complete cycles of the input signal. Draw the input waveform in Graph 1 and measure the peak-to-peak value. Record this in Table 1. Convert this value into RMS value using the formula: 3. 4. Vp-p Vp-p P-P VRMS 2.828
p3. A biased parallel clipper is connected to a squarewave 20VAC input.The biasing voltage of 5V has the same polarity with the Vo while the Si diode is connected in reverse and will conduct only during negative half cycle. In P3, what is the output voltage (Vo) during the positive half cycle? a. -4.3V b. 20V c. 4.3V d. -12.15V