The 46-mm diameter shaft is supported by a smooth thrust bearingat A and a smooth journal bearing at B. The pulleys C and D aresubjected to the vertical and horizontal loadings shown in the figurebelow. (Figure 1)Figure400 mm400 mmCC300 N 300 N400 mmD<150 N150 NB1 of 1 ▶Part ADetermine the absolute maximum bending stress in the shaft.Express your answer to three significant figures and include the appropriate units.Omax=SubmitProvide FeedbackuAValuefRequest AnswertOUnits?

Here we will apply the bending stress formula from the bending equation

The 46-mm diameter shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. The pulleys C and D are subjected to the vertical and horizontal loadings shown in the figure below. (Figure 1) ▼ Part A Determine the absolute maximum bending stress in the shaft. Express your answer to three significant figures and include the appropriate units.

The 46-mm diameter shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. The pulleys C and D are subjected to the vertical and horizontal loadings shown in the figure below. (Figure 1) ▼ Part A Determine the absolute maximum bending stress in the shaft. Express your answer to three significant figures and include the appropriate units.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.12.3P: A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0...

See similar textbooks

Similar questions

What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
A solid circular shaft AB of diameter d is fixed against rotation at both ends (sec figure), A circular disk is attached to the shaft at the location shown. What is the largest permissible angle of rotation 0max of the disk if the allowable shear stress in the shaft is Tallow? [Assume that a >b. Also, use Eqs. (3-50a and b) of Example 3-9 to obtain the reactive torques.]
The 46-mm diameter shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. The pulleys C and D are subjected to the vertical and horizontal loadings shown in the figure below. (Figure 1) Part A Determine the absolute maximum bending stress in the shaft. Express your answer to three significant figures and include the appropriate units. ? Omax = 10.7 MPa Submit Previous Answers Request Answer X Incorrect; Try Again; 29 attempts remaining Provide Feedback Figure 150 N 400 mm 150 N 300 N 300 N 400 mm 400 mm
A 45-mm-diameter solid steel shaft supports loads PA-1.2 KN and Pc-2.7 kN as shown. Assume that L₁ - 105 mm, L₂ = 205 mm, and 43-150 mm. The bearing at B can be idealized as a roller support, and the bearing at D can be idealized as a pin support. Determine the magnitude of (a) the maximum horizontal shear stress in the shaft. (b) the maximum tension bending stress in the shaft. L₂ C Pc Ly D
A shaft required to transmit 50kW of power will be running at 100rev/min. The maximum twist in 3m length of the shaft is limited to 1.5 degree. If the maximum torque is 30 percent more than mean or average torque. Assume entirely elastic action and take modulus of rigidity for the shaft material G = 135 GN/?2. Determine the following:a. Diameter of the shaft.b. Maximum shear stress developed in the shaft. I need answer ASAP. Thank you!
The steel shaft of a socket wrench has adiameter of 8.0 mm and a length of 200 mm (seefigure).If the allowable stress in shear is 60 MPa, whatis the maximum permissible torque Tmax that may beexerted with the wrench?Through what angle f (in degrees) will the shafttwist under the action of the maximum torque?(Assume G = 78 GPa and disregard any bending ofthe shaft.)
The 46-mm diameter shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. The pulleys C and D are subjected to the vertical and horizontal loadings shown in the figure below. (Figure 1)
The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. (Figure 1) Figure 1 m 1 m 30 mm 40 mm B - 1 m D 1 of 1 Part A If P = 22 kN, determine the absolute maximum shear stress in the shaft. Express your answer to three significant figures and include the appropriate units. Tmax= Submit Provide Feedback μA Value Request Answer Units ?
The aluminum shaft, composed of three segments is fastened to rigid supports as A and D. Calculate the maximum shear stress in each segment when the two torques are applied. A 400 N-m 850 N-m L=1.4 m 30 mm diameter B L=2.4 m 50 mm diameter L-1.9 m 30 mm diameter