The block shown in (Figure 1) has a mass of m = 75 kg, a height H 1.1 m, and width L = 1.6 m. It is resting on a ramp that makes an angle = 34° with the horizontal. A force P is applied parallel to the surface of the ramp at the top of the block. What is the maximum force that can be applied without causing the block to move? The coefficient of static friction is μ, = 0.42, and the center of mass of the block is at the center of the rectangle. Part E What is the maximum magnitude of P that can be applied before tipping would occur, assuming the block does not slip? Express your answer to three significant figures with appropriate units. HÅ Ptip = Value undo Units Figure Submit Request Answer 1 of 2 Part F What is the maximum magnitude of P that does not cause motion of the block? Express your answer to three significant figures with appropriate units. Panax = |667.611 ? N Submit Previous Answers Request Answer

The block shown in (Figure 1) has a mass of m = 75 kg, a height H 1.1 m, and width L = 1.6 m. It is resting on a ramp that makes an angle = 34° with the horizontal. A force P is applied parallel to the surface of the ramp at the top of the block. What is the maximum force that can be applied without causing the block to move? The coefficient of static friction is μ, = 0.42, and the center of mass of the block is at the center of the rectangle. Part E What is the maximum magnitude of P that can be applied before tipping would occur, assuming the block does not slip? Express your answer to three significant figures with appropriate units. HÅ Ptip = Value undo Units Figure Submit Request Answer 1 of 2 Part F What is the maximum magnitude of P that does not cause motion of the block? Express your answer to three significant figures with appropriate units. Panax = |667.611 ? N Submit Previous Answers Request Answer

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter12: Static Equilibrium And Elasticity

Section: Chapter Questions

Problem 79CP: In order to lift a shovelful of dirt, a gardener pushes downward on the end of the shovel and pulls...

See similar textbooks

Similar questions

When tightening a bolt, you push perpendicularly on a wrench with a force of 165N at a distance of 0.140m from the center of the bolt. How much torque are you exerting relative to the center of the bolt?
In order to lift a shovelful of dirt, a gardener pushes downward on the end of the shovel and pulls upward at distance l2 from the end, as shown below. The weight of the shovel is mg and acts at the point os application of F2 . Calculate the magnitudes of the forces F1 and F2 as functions of l1 , l2 , mg, and the weight W of the load. Why do your answers not depend on the angle that shovel makes with the horizontal?
This problem concerns the concept of tension in a rope. Consider a rope subjected to a pulling force on its two ends as shown in (Figure 1). The rope is stationary. An arbitrary point P divides the rope into a left-hand segment L and a right-hand segment R. Figure wi L pull R 232 pull 1 of 3 Part A For segment R and segment L to hold together, they must exert forces on each other. What is the direction of the force exerted on segment R by segment L? View Available Hint(s) left right Submit Part B FLR Assume that segment R exerts a force of magnitude T' on segment L. What is the magnitude FLR of the force exerted on segment R by segment L? Give your answer in terms of T and other constants such as g. ► View Available Hint(s) = Submit % ΑΣΦ www ?
A 60.0 cm, uniform, 50.0 Nshelf is supported horizontally by twov verticalwires attached to the slopingc ceiling(Fig. ). A very small 25.0 N tool is placed on the shelf midway between the points where the wires are attached to it. Find the tension in each wire. Begin by making a free-body diagram of the shelf.
A 1.5 kg block resting ina rough flat surface is pulled by a string. The string makes an angle of 20 degress with the horizontal. The coefficient of static friction between the blodk and the surface is 0.35. What is the maximum tension in the string to keep the block unmoved?
A 1.70 kg box rests on a plank that is inclined ut an angle of 63.0° above the horizontal. The upper end of the box isattached to a spring with a force constant of 16.0 N/m, as shown in the figure. If the coefficient of static friction betweenthe box and the plank is 0.26, what is the maximum amount the spring can be stretched and the box remain at rest?
A 10kg block resting on the flat frictionless plane is pushed by a force directed force of 20N 60deg S to E . What is the magnitude of normal force acting on the block?
16. ao The drawing shows a rectangular piece of wood. The forces applied to corners B and D have the same magnitude of 12 N and are directed parallel to the long and short sides of the rectangle. The long side of the rectangle is twice as long as the short side. An axis of ro- tation is shown perpendicular to the plane of the rectangle at its center. A third force (not shown in the drawing) is applied to cor- ner A, directed along the short side of the rectangle (either toward B or away from B), such that the piece of wood is at equilib- rium. Find the magnitude and direction of the force applied to corner A. A D Axis Problem 16
A block with a mass m = 10kg is sitting on an inclined plane witn an angle of 30 degrees. The block is connectec to a wall by a wire which has tension so that the block is stationary. The coefficient of static friction between the block and the plans is 0.2. Calculate tension
SAQ 1 1.2 m D C An 80-kn'm couple shown in the plate is caused by a pair of parallel forces of magnitude F (not shown). Determine: 80 kN m a) the smallest possible value of F, and 1.6 m b) the value of F if the forces act at points A and C and are parallel to the dashed line shown at A. A В 60°
The angle of inclination of the wedge and block is 25°. The angle of friction all contact surface is 17°. Determine the P required to pull the wedge from under the 500 N block if the block is against the wall. Assume rough contact surfaces.
In the figure below, the horizontal boom is uniform and has the same weight as the hanging weight at its end. The boom is supported by the cable with a tension T. The angle between the boom and the cable is 30°. What is the magnitude of horizontal force Fx exerted by the wall on the boom? Fy Fx W