The composite beam consists of a wood core and twoplates of steel. If the allowable bending stress for thewoodis= 20 MPa,andthesteel(Callow)w130 MPa, determine the maximum bendingfor(Tallow) stmoment that can be applied to the beam. Ew= 11 GPa, Est= 200 GPa.125 mmM20 mm-75 mm20 mm

Given data Allowable bending stress for wood, 20MPa Allowable bending stress for steel, 130MPa…

The composite beam consists of a wood core and two plates of steel. If the allowable bending stress for the (Tallow) w 130 MPa, determine the maximum bending wood is 20 MPa, and for the steel (Tallow)st moment that can be applied to the beam. EN 11 GPa, Est = 200 GPa. 125 mm M 20 mm 75 mm 20 mm IN

The composite beam consists of a wood core and two plates of steel. If the allowable bending stress for the (Tallow) w 130 MPa, determine the maximum bending wood is 20 MPa, and for the steel (Tallow)st moment that can be applied to the beam. EN 11 GPa, Est = 200 GPa. 125 mm M 20 mm 75 mm 20 mm IN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

6-122 Segment A of the composdte heam is made from 2014-T6 aluminum alloy and segment Bs A-36 steel. If w - 0.9 kip/, determine the absolute maximum bending stress developed in the aluminum and steed. Skelch the stress distribution on the cross section. 6-123. SegmentA of the composite beam is made trom 2014-T6 aluminum alkoy and segment B s A-36 steel. The alowable bending stress for the aluminum and steel are (a)¬15 ksi and (a -22 k.Determine the maximum alowahle Intensity w of the uniform distributed kad. -15 h Probs. 6-122/123
"6-120. The composite beam is made of steel (A) bonded to brass (B) and has the cros section shown. IIt is subjected to a moment of M - 65 KN - m, determine the maximum bending stress in the brass and steel. Alsa, what is the stres In cach material at the seam where they are bonded together? E- 100 GPa, E-20O GPa. 6-12L The composile beam is made of steel (A) bonded to bras (8) and has the cros section shown. II he alkwable bending stress far the sted is (oae- 180 MPa, and for the bras (oa-0 MPa, delermine the matimum moment M that can be appiled to the beam. -100 GPa, E-200 GPa Imim Y 200 mm 175 m Probs. 6-12121
The composite beam consists of a wood core and two plates of steel. If the allowable bending stress for the wood is (ơallow)w = 20 MPa, and for the steel (ơallow)st = 130 MPa, determine the maximum shear v that can be applied to the beam. Ew = 11 GPa, E = 200 GPa. 125 mm Given: (7allow),vood = 6.5 MPa E n = Ew 200(10°) 11(10°) = 18.182 1 (0.80227)(0.125) = 0.130578(10-³)m* 12 I = 20 mm- 75 mm Failure of wood : 20 mm Mc (om)max = I M(0.0625) 20(10°) M = 41.8 KN•M 0.130578(10 125mm Failure of steel : nMc (ơ1)max = I 18.182(M)(0.0625). 0.130578(10¬³) 130(10“) M = 14.9 kN •m (controls) A maximum moment that can be applied to the beam.
Question 2 : The composite beam consists of a wood core and two plates of steel. If the allowable bend ng stress for the wood is (oaiow )y = 20MPa and for the s(o aienl =130MPA zilow determine the maximum moment that can be applied to the beam. E, =11GPA , E= 200GPA Take: A = 125 mm A mm B = 75 mm M 20 mm- B mm 20 mm Solution : E 200(10" E 1110° The width of steel must be increased to an equivalent width for wood: Page 1 18.182 W. mm
The rod is supported by smooth journal bearings at A and B that only exert vertical reactions on the shaft. Part A Determine its smallest diameter d if the allowable bending stress is oallow = 130 MPa (Figure 1) Express your answer with the appropriate units. HA ? d = Value Units Figure < 1 of 1 Submit Request Answer 12 kN/m Provide Feedback 3 m 1.5 m
Q1/ A composite beam is made of wood and reinforced with steel strap located on its bottom side. It has the cross-sectional area shown in fig. if the beam is subjected to a bending moment of M=2kN.m, determine the normal stress at wood and steel. Take Ew=12Gpa and Est=200Gpa. 150mm Wood en 20mm Steel 150mm
A beam fabricated from western white pine has been reinforced by bonding steel strips on its top and bottom surfaces as shown. If the design is limited to a wood 1 ksi in the wood and steel = 34.4 ksi in the steel, determine the maximum bending moment if the beam bends about its horizontal axis of symmetry. Given: • L₁ = 11.2 in • L₂ = 1.7 in • L3 = 4.3 in Mmar STEEL N.A. Pa WOOD number (rtol=0.01, atol=1e-05) 1 -L3 1 1 1 1 1 1 L₂ L₁ L2 kip. in e
A beam fabricated from western white pine has been reinforced by bonding steel strips on its top and bottom 1.5 ksi in the surfaces as shown. If the design is limited to wood = 1.5 ksi in the wood and a steel wood and steel = 35.6 ksi in the steel, determine the maximum bending moment if the beam bends about its vertical axis of symmetry. L3 Given: • L₁= 10 in • L₂ L₂ = 0.9 in • L3= 5.3 in Mmar SEHERAPECES SANTREMANEN La prender PERANAN PE P number (rtol-0.01, atol=1e-05) STEEL E WOOD N.A. L₁ kip. in L₂ L₂ Phu
Consider the reinforced cConcrete beam shown. The 250 mm beam is subjected to a positive bending moment of 175 kNm. Determine the stress in the steel and the maximum stress in the concrete. Use E=2.5 GPa for the concrete and 200 GPa for the steel. Use concrete as the reference material. I mm4 O po o SO mum Ost MPa (Ocon)max 4 pcs. MPa 20mmø Please follow this format in answering. Given: Required: n I in mm4 Ost in MPa (O con)max in MPa Solution: (Please answer in detailed (step by step). Indicate labels on what you are doing/performing, for example what formula is used) After the computation, provide an explanation (in words) of how you solve the problem; the step-by-step process that you took, the strategy, etc. W ost
The composite beam consists of a wood core and two plates of steel. If the allowable bending stress for the wood is (sallow)w = 20 MPa, and for the steel (sallow)st = 130 MPa, determine the maximum moment that can be applied to the beam. Ew = 11 GPa, Est = 200 GPa.
A log that is 2 ft in diameter is to be cut into a rectangular section for use as a simply supported beam. If the allowable bending stress is sallow = 8 ksi, determine the required width b and height h of the beam that will support the largest load possible. What is this load?
. A composite beam, made of aluminum (Al) and magnesium (Mg), has the cross section shown below. The moduli of elasticity for aluminum and magnesium are EAI = 70 GPa and EMg = 45 GPa, respectively. If the allowable flexural stresses (in tension and com- pression) are All 135 MPa for the aluminum and Mg 120 MPa for the magnesium, determine the maximum allowable bending moment for the beam. all - 0.2 m 0.2 m Al 0.2 m Mg C