The cylinder shown below with a one-inch piston rod is being extended and the flow control valve labelled F1 has a diameter of half inch. What would be the approximate flowrate through the valve. Calculate the HP provided by the prime mover, the HP lost across the valve and the HP delivered to the cylinder. Also, calculate the speed at which the cylinder will extend if the area of the cylinder bore is three times the area of the piston rod. Will the cylinder retract at the same speed if flowrate at the other end of the cylinder is the same, explain why. What should be the approximate size of the reservoir to ensure sufficient oil is always present in the reservoir?

The cylinder shown below with a one-inch piston rod is being extended and the flow control valve labelled F1 has a diameter of half inch. What would be the approximate flowrate through the valve. Calculate the HP provided by the prime mover, the HP lost across the valve and the HP delivered to the cylinder. Also, calculate the speed at which the cylinder will extend if the area of the cylinder bore is three times the area of the piston rod. Will the cylinder retract at the same speed if flowrate at the other end of the cylinder is the same, explain why. What should be the approximate size of the reservoir to ensure sufficient oil is always present in the reservoir?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. As shown in the Figure 12, for the variable speed cylinder, a and b are the oil inlet and c is the oil return port. It is already known that D3D200 mm, d1=160 mm and d=D40mm. The flow rate of the hydraulic pump is q-60L/ min. Calculation: the velocity of the piston when the pump only supplies oil to port a and the velocity of the piston when it supplies oil to port a and b at the same time. Figure 12
The bore and stroke of an air compressor are 276mm and 164mm, respectively. If the piston displacement is 0.049m3/sec, what is the operating speed of the compressor?
a pump is delivering 160 liters per sec of water using an impeller diameter of 240 mm and operating at a speed of 1800 rpm. if the speed held constant and the impeller diameter is change to 203.2 mm, what is the new dischange og the pump in liters per second
A model of a hydraulic turbine is tested at a head of 1/4th of that under which the full scale turbine works. The diameter of the model is half of that of the full scale turbine, if Nis the RPM of the full scale turbine, then RPM of the model will be
| Centrifugal pump impeller runs at 950 rpm. Its external and internal diameters are 500 mm and 250 mm. The vanes are set back at an angle of 35° to the outer rim. If the radial velocity of water through the impeller be maintained constant as 2 m/sec, find the angle of the vanes at inlet, the velocity and direction of water at outlet and the work done by the impeller per kg of water
Draw the right diagram for the problem. Show complete solution. Water at 60 F from a lake through 500 ft if 4in ID cast iron pipe at a water turbine 250 ft below the surface of the lake. After flowing from the turbine, the water is discharged into the atmosphere through a horizontal 50 ft section of the same pipe. The turbine power output is 10hp when the water in the discharged pipe is flowing at 5 ft/s. a. What is the turbine efficiency defined as the actual power output of the turbine divided by the power output that would be withdrawn if there are no friction within the turbine? b. If the turbine were by passed, what would be the flow rate of water through the 500 ft of 4in pipe?
The bore and stroke of an air compressor are 276mm and 164mm, respectively. If the piston displacement is 0.049m3/sec, what is the operating speed of the compressor? complete soln tnx.
A canon is used to fire a bomb with velocity 20 m/s. If angle of projection is varied from 20 degrees to 70 degrees, plot the range. At which angle this range is maximum?
Water enters a pump through a 250 mm diameter and leaves the pump through a 150 mmdiameter pipe. If the flow rate is 150 li/s, compute the following:a. Velocity of suction pipe.b. Velocity of discharge pipe.
Provide the diagram for the problem. Choose the correct answer and provide complete solution. Water at 60 F from a lake through 500 ft if 4in ID cast iron pipe at a water turbine 250 ft below the surface of the lake. After flowing from the turbine, the water is discharged into the atmosphere through a horizontal 50 ft section of the same pipe. The turbine power output is 10hp when the water in the discharged pipe is flowing at 5 ft/s. A. What is the turbine efficiency defined as the actual power output of the turbine divided by the power output that would be withdrawn if there are no friction within the turbine? a. 86%b. 65%c. 77%d. 50% B. If the turbine were by passed, what would be the flow rate of water through the 500 ft of 4in pipe. a. 45 lb/sb. 37 lb/sc. 52 lb/sd. 29 lb/s
A wind turbine rotates at speed of 300 rpm. What is the circumferential velocity at the tip of the blade if TSR is 2? If wind is at velocity of 7 m/s, what is the rotor radius to meet the required rpm?
A pump has a specific speed of 5.0. Its head is 1.0 m. Let D = 0.6 m. Determine itsvolume flowrate if the rotative speed is 1500 rpm.