The diameter of the pipe at point B is larger than at point A. - At which point is the water speed greater? Point B Point A It is the same at both points. Cannot be determined from the information given.

The diameter of the pipe at point B is larger than at point A. - At which point is the water speed greater? Point B Point A It is the same at both points. Cannot be determined from the information given.

Name: The diameter of the pipe at point B is larger than at point A.- At whi
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: The diameter of the pipe at point B is larger than at point A.- At which point is the water speed greater? Point B Point A It is the same at both points. Cannot be determined from the information given.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.85P: Find the surface area of the 90 duct elbow.

See similar textbooks

Similar questions

Manometer being used to indicate the pressure difference between two points in a fabricated system. Calculate the velocity at A and B if the manometer deflection h is 250 mm. (This arrangementis called a venturi meter, which is often used for flow measurement.) (WE CAN USE THE FLOWRATE EQUATION Q=Av). Find; vA and vB
A centrifugal water pump has a discharge flow rate of 25 gpm. A pressure gauge at the pump suction flange indicates a pressure of -10 psig, while a pressure gauge at the pump discharge flange indicates a pressure of 30 psig. The suction and discharge flanges has the same internal diameter. Also, the elevation difference between the suction and discharge flanges is about 13 inches. Estimate the total dynamic head of the pump in feet. Round your answer to 2 decimal places.
The diameter of the pipe at the larger end is 0.50 cm and at the smaller end is 0.20 cm, the larger and smaller ends located 7 meters and 3 meters respectively, from the datum line. If the larger end, the velocity is 1.2 m/s and the pressure is 5200 kN/m2 , compute the velocity at the smaller end.
If a turbulent water flows inside the piping system, the vertical distance h=30 mm, what is the velocity m/s of water at section A. Given that the area of A=3.1 A. A EGL HGL h
The flow carried by pipe below discharges into the open atmosphere. If the pipe length is 300 m, diameter is 150 mm and roughness of 0.0025 mm, write the equation(s) required to determine the maximum discharge.
The water of a 14’ × 48’ metal frame pool can drain from the pool through an opening at the side of the pool. The opening is about h = 1.05 m below the water level. The capacity of the pool is V = 3740 gallons, the pool can be drained in t = 10.2 mins. P0 is the pressure of the atmosphere. ρ is the density of the water. a. Write the Bernoulli’s equation of the water at the top of the pool in terms of P0, ρ, h. Assuming the opening is the origin. b. Write the Bernoulli’s equation of the water at the opening of the pool in terms of P0, ρ, h and v, where v is the speed at which the water leaves the opening. Assuming the opening is the origin. c. Express v2 in terms of g and h. d. Calculate the numerical value of v in meters per second. e. Express the flow rate of the water in terms of V and t. f. Express the cross-sectional area of the opening, A, in terms of V, v and t. g. Calculate the numerical value of A in cm2
A pipe 5 m long is inclined at 15° with horizontal.The smaller section of the pipe is in 80 mm diameter & at lower level whereas other section is 240 mm diameter. Determine the difference of pressure between two sections. Pipe is uniformly tapering & the velocity of water at smaller section is 1 m/s. Also show the direction of flow of water. 5 m 0 = 15° datum line 2.
What time (in second) is required to fill the circular tank with incompressible water from h= 2 m to H=15.0 m? D-20 cm H water d1= 4cm v1-5 mls d2=3 cm v2=2 m/s F10 F11 F12 PrtScr Insert Delete 81 Nam Backspace Lock
P1 = Patm 1 V1 = 7.3 m/s Flow h = 0.96 ft water 2 3 Density of water 1000 kg/m3 Determine the pressure at the point 3?
A hose discharges water from a tank as shown. Find the rate of discharge and the pressure head at point "B" if the hose has a uniform diameter of 6 inches. Assume that the energy loss in the hose due to friction is zero. All dimensions given in the diagram have units of feet. Show all your work in detail. B м 16'
Three hundred and eighty five gallons of water per minute is flowing through a 4.3-in radius horizontal pipe. If the bore of the pipe is reduced to 2.7-in radius and the pressure in the smaller pipe is 93 psig, what is the pressure in the larger section of the pipe? Include schematic diagram.
6) Determine the internal energy of water at 20 psi and 400 F