The electrical load in a factory has 1800 kW and a trailing power factor of 0.6. It A second load will be added to the factory. This new load consumes 600 kW of real power. When the load is added the power factor of the total load will be 0.96 (trailing). a) Find the reactive power of the added load. b) Is the added load capacitive or inductive? c) What is the power factor of the added load? d) The input voltage of the factory is 4800 V (rms). Before and after the load is added to the factory What is the rms magnitude of the input current?

The electrical load in a factory has 1800 kW and a trailing power factor of 0.6. It A second load will be added to the factory. This new load consumes 600 kW of real power. When the load is added the power factor of the total load will be 0.96 (trailing). a) Find the reactive power of the added load. b) Is the added load capacitive or inductive? c) What is the power factor of the added load? d) The input voltage of the factory is 4800 V (rms). Before and after the load is added to the factory What is the rms magnitude of the input current?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

what is the reactive power absorbed by the load ZL in VAR? Assume source is in rms
15. You are working on a power factor correction installation, and you notice with a clip-on ammeter as you add in capacitance the current drops, you add more capacitance and the current drops, you add more capacitance the current rises. How do you know when you are at unity power factor?
Please read questions carefully i need power factor and Reactive power of load
A circuit having power factor of 0.8 consumes 40 W. What will be the value of reactive power of the circuit ?
Assume that the load resistance can be varied between 0 and 4000 Ω andthat the capacitive reactance of the load can be varied between 0 and−2000 Ω. What settings of RL and XL transfer the most average powerto the load? What is the maximum average power that can be transferredunder these restrictions?
If a Load absorbs 10 kVA at a leading power factor of 0.6. Then the complex power is: Select one: a. 6000 - j8000 VA b. 6000 + j8000 VÀ C. -6000 - j8000 VA O d. None of these
Use the information below to answer questions 24 und 25. The voltage across and the current through a load are (10+ j5Y and (2-jiArespecively. 24. What is the reactive power in VArconsumed? D. 0 A. 15 C. 20 D. 25 25. What is the pawer factor of the load? A. 0.8 leading B. 0.8 Jagging. -D. 0.6 ligging C 0.6 leading
An rms voltage of 22.2 V with a frequencyof 1.00 kHz is applied to a 0.290-mH inductor. (a) What is the rmscurrent in this circuit? (b) By what factor does the current changeif the frequency of the voltage is doubled? (c) Calculate the current for a frequency of 2.00 kHz
2. A triangular voltage source has a peak value of 10 V. What is the computed RMS value of this source? a. 3 V b. 4 V c. 5 V d. 6 V 3. In Question 2, if the source is measured by an analog meter, will it show the correct RMS value? a. Yes b. No
Problem 1 • A sinusoidal source with frequency of 60 Hz and rms-voltage of 100 V is connected to an RL load of 10 ohms and 100 uH. Find Power Factor From Calculation Find Power Factor From Plot L=10mH find power factor from calculation only
Lo au If a Load absorbs 10 kVA at a lagging power factor of 0.6. Then the complex power is: Select one: O a 6000 j8000 VA Ob.6000-j8000 VA c. None of these Od-6000 + j8000 VA eafermer
A 5-ohm resistor is connected in series with a 25 micro-farad capacitor. A source voltage of 158 volts, 50 Hz supplies the combination. Determine the following: a. Circulating current b. Voltage across the resistor c. Voltage across the capacitor d. Real power supplied by the source e. Reactive power supplied by the source f. Apparent power of the circuit g. Power factor of the entire circuit