The following holds true for the latent heat of fusion of a material except for a. The heat of fusion is a property of the material. b. The heat of fusion describes the amount of heat per unit mass needed to change the phase of the material. c. The heat of fusion of directly proportional to the temperature. d. The heat of fusion is constant.

The following holds true for the latent heat of fusion of a material except for a. The heat of fusion is a property of the material. b. The heat of fusion describes the amount of heat per unit mass needed to change the phase of the material. c. The heat of fusion of directly proportional to the temperature. d. The heat of fusion is constant.

Physics for Scientists and Engineers, Technology Update (No access codes included)

9th Edition

ISBN:9781305116399

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter20: The First Law Of Thermodynamics

Section: Chapter Questions

Problem 20.4OQ

See similar textbooks

Similar questions

A person inhales and exhales 2.00 L of 37.0C air, evaporating 4.00102g of water from the lungs and breathing passages with each breath. (a) How much heat transfer occurs due to evaporation in each breath? (b) What is the rate of heat transfer in watts if the person is breathing at a moderate rate of 18.0 breaths per minute? (c) If the inhaled air had a temperature of 20.0C, what is the rate of heat transfer for warming the air? (d) Discuss the total rate of heat transfer as it relates to typical metabolic rates. Will this breathing be a major form of heat transfer for this person?
(a) What is the rate of heat conduction through the 3.00-cm-thick fur of a large animal having a 1.40m2 surface area? Assume that the animal’s skin temperature is 32.0C, that tile air temperature is 5.00C, and that fur has the same thermal conductivity as air. (b) What food intake will the animal need in one day to replace this heat transfer?
(a) Calculate the rate of heat conduction through house walls that are 13.0 cm thick and that have an average thermal conductivity twice that of glass wool. Assume there are no windows or doors. The surface area of the walls is 120m2 and their inside surface is at 18.0C, while their outside surface is at 5.00C. (b) How many 1-kW room heaters would be needed to balance the heat transfer due to conduction?
(a) How much heat transfer is required to raise the temperature of a 0.750kg aluminum pot containing 2.50 kg of water from 30.0C to the boiling point and then boil away 0.750 kg of water? (b) How long does this take if the rate of heat transfer is 500 W 1watt=ljoule/second(lW=lJ/s) ?
. On a winter day, the air temperature is — 15°C, and the humidity is 0,001 kg/m3. (a) What is the relative humidity? (b) When this air is brought inside a building, it is heated to 20°C. If the humidity isn't changed, what is the relative humidity inside the building?
(a) Calculate the rate of heat conduction through house walls that are 13.0 cm thick and have an average thermal conductivity twice that of glass wool. Assume there are no windows or doors. The walls' surface area is 120 m2 and their inside surface is at 18.0 , while their outside surface is at 5.00 . (b) How many 1-kW room heaters would be needed to balance the heat transfer due to conduction?
Assume you are measuring the specific heat of a sample of originally hot metal by using a calorimeter containing water. Because your calorimeter is not perfectly insulating, energy can transfer by heat between the contents of the calorimeter and the room. To obtain the most accurate result for the specific heat of the metal, you should use water with which initial temperature? (a) slightly lower than room temperature (b) the same as room temperature (c) slightly higher than room temperature (d) whatever you like because the initial temperature makes no difference
A high-end gas stove usually has at least one burner rated at 14 000 Btu/h. (a) If you place a 0.25-kg aluminum pot containing 2.0 liters of water at 20.C on this burner, how long will it take to bring the water to a boil, assuming all the heat from the burner goes into the pot? (b) Once boiling begins how much time is required to boil all the water out of the pot?
One easy way to reduce heating (and cooling) costs is to add extra insulation in the attic of a house. Suppose the house already had 15 cm of fiberglass insulation in the attic and in all the exterior surfaces. If you added an extra 8.0 cm of fiberglass to the attic, then by what percentage would the heating cost of the house drop? Take the single story house to be of dimensions 10 m by 15 m by 3.0 m. Ignore air infiltration and heat loss through windows and doors.
(a) Suppose a meter Stick made of steel and one made of invar (an alloy of iron and nickel) are the same length at 0C. What is their difference in length at 22.0C ? (b) Repeat the calculation for two 30.0mlong surveyor's tapes.
€69. Integrated Concepts (a) A large electrical power facility produces 1600 MW of “waste heat.” which is dissipated to the environment in cooling towers by warming air flowing through the towers by 500C. What is the necessary flow rate of air in m3/s ? (b) Is your result consistent with the large cooling towers used by many large electrical power plants?
Which of the following correctly describes the rate of conductive heat transfer for a substance? a. The rate decreases with increased surface area and decreased thickness. b. The rate increases with increased temperature difference and surface area. c. The rate increases with decreased temperature difference and increased thickness. d. The rate decreases with decreased temperature difference and increased surface area.