The following information is given for a 300kW, 600V, long shunt compound DC generat or, shunt fieldresistance is 75 ohms, armature resistance 0.01, brush resistance is 0.011 ohrms, series field resistance is0.012 ohms and the divert or resistance of 0.036 ohms.When the machine is delivering full load; a. Drawthe circuit diagrarn b. Calculate the voltage and C Power generated by the armat ure.

Drawing the circuit for the given case:

The following information is given for a 300kW, 600V, long shunt compound DC generat or, shunt field resistance is 75 ohms, arrmat ure resistance 0.01, brush resistance is 0.011 ohms, series field resistance is 0.012 ohms and the divert or resistance of 0.036 ohms.When the machine is delivering full load; a. Draw the circuit diagram b. Calculate the voltage and C Power generated by the armature.

The following information is given for a 300kW, 600V, long shunt compound DC generat or, shunt field resistance is 75 ohms, arrmat ure resistance 0.01, brush resistance is 0.011 ohms, series field resistance is 0.012 ohms and the divert or resistance of 0.036 ohms.When the machine is delivering full load; a. Draw the circuit diagram b. Calculate the voltage and C Power generated by the armature.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Similar questions

A field excitation of 20 A in a certain alternator results in an armature current of 400 A in short circuit and a terminal voltage of 2000 V on open circuit. The magnitude of the internal voltage drop within the machine at a load current of 200 A is
Speed control of a 140 V, 1.68 kW DC motor single phase thyristor full wave AC-DC It is made by the converter. AA supply voltage 220 V (rms) Is 50. In the converter It is assumed that there is no loss. The armature resistance of the DC motor is = 0.417 Q. Very a large inductance is connected in series with the motor. The motor voltage constant is = 0.0964 V/rpm. The motor can be considered as a permanent magnet DC. According to this, a) Draw the driver (converter-motor) power circuit. b) Calculate the nominal current of the motor. c) Supply voltage, supply current, converter output voltage for ignition angle a = 30 ° and Draw the waveforms for the converter output current. d) = 950 rpm and for nominal current, d1) The firing angle of the converter, d2) Effective value of supply and thyristor current, d3) Supply power factor, calculate.
The DC shunt generator with the terminal voltage 300 V, armature drop 8 V and the each brush drop 2 V, then the value of generated emf is
Q9 / What are the function of brushes , pole and commutator in DC machine
Get the electromechanical analog model (torque-voltage or torque-current) of the system. With all the steps of the analysis
How voltage is built up in dc shunt generator
With a labelled diagram of any DC machine Discuss it parts
Draw dc load line :
A 20 kVA machine has a full load copper loss of 400 W, an iron loss of 150 W, and a mechanical loss of 200 W. Determine:a) Efficiency at 3/4 of full load with f.d.p. 0.8. Ans: 95,43%b) Performance at full load with f.d.p. 0.9. Ans: 96%c) Peak performance apparent power. Ans: 18,71 kVAd) Yield in the previous case for f.d.p. Unit. Ans: 96,39% I need the procedures to get these results. Thanks
Maz a) A sinewave is having a frequency of 50 Hz and instantaneous value of 250 Volts at 1.3 milli seconds. Find D The maximum value of sinusoidal voltage waveform and i) The value of voltage at 2.1 milli seconds. b) Determine the instantaneous equation for the voltage waveform shown in figure, if Vp=100 Volts, Time period is 10 milli seconds and 0 =40 degrees. on Vp Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. a) (i) Maximnum value = a) (ii) Value of voltage at 2.1 ms = b) Angular frequency =
h) Explain the methods of voltage control used in AC-AC converters.
Untitled Section Jalis 6 In d.c. generators armature reaction is produced by field current O armature current commutating winding current none of the mentioned compensating winding current *.The use of d.c. generators eliminated the use of rectifiers and ac supplies True False O