The plug has a diameter of 30 mm and fits inside a rigid sleeve with an inner diameter of 32 mm. Both the pin and sleeve are 50mm in length. Both elements are made of 304 stainless steel alloy. Determine the axial tension that must be applied to the top and bottom of the sleeve to cause it to contact the sides of the dowel. Also, please indicate if you can actually compress your sleeve to achieve this?

The plug has a diameter of 30 mm and fits inside a rigid sleeve with an inner diameter of 32 mm. Both the pin and sleeve are 50mm in length. Both elements are made of 304 stainless steel alloy. Determine the axial tension that must be applied to the top and bottom of the sleeve to cause it to contact the sides of the dowel. Also, please indicate if you can actually compress your sleeve to achieve this?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

with the steel bar having 16 mm diameter
For the same question, the M25 Screw will be used when pressing the Nut Wheel onto the shaft. Assuming that the force that the nut needs to suppress is Fçak=1218 kgf (it was found in the previous question, but we don't use it), what should the minimum NUT HEIGHT be in mm to create this force safely? (Screw and Nut's surface safety pressure Pem=45 N/mm2 Screw base diameter d1= 21.5 mm. (Calculate the pitch (h=?) according to the given ones, considering that metric screw is used!)
Pressure vessel having 20in diameter is under a repeated load with a maximum pressure of 350psi per cycle. The vessel is made of AISIC1095. Determine its thickness.
The two steel shafts (1) and (2) each Ø10 should be connected to each other with the help of the sleeve (3) (Øinner = 10, Øoutside = 15) also made of steel and two rivets at the points shown. The shaft (1) is firmly clamped on the left- hand side, the force F = 100 N acts on shaft 2 in the direction of the arrow. How are the brass round rivets to be dimensioned so that a safety of the coupling against failure of S = 10 is achieved? hole for rivets 1 F 3 a) What type of connection does a riveted connection have? b) What type of load does the rivet have? c) What is the diameter of the rivets? d) Which areas of the rivet are loaded? (Draw in figure and formula) e) Dimension the rivet
A cylindrical pressure vessel of radius r = 10.2 in is filled with a gas at a pressure of 455.0 psi (gauge). The top of the vessel is secured by an end cap of radius R = 22.0 in, of weight 31.0 lbf, and held in place by 14 bolts. Bolts (more exist than sh End cap
3. At temperature T₁, the two rigidly connected rods just fit the rigid supports. If both sections are identical except for the diameter, prove that the following equations are true when temperature rises to T₂. a. F= b. OAB C. OBC A x(T₂-T₁)лd²E 20 x(T₂-T₁)E 5 9x(T₂-T₁)E 5 -1/2- d B 1/12- d C
What will be the minimum diameter of a steel wire, which is used to raise a load of 4000N if the stress in the rod is not to exceed 95 MN/m²?
find the tensile of the bolt with diameter 38mm,80kN
If P is equivalent to 94 kN, the diameter at pin B is Blank 1 mm.
Part A Direct tension indicators are sometimes used instead of torque wrenches to ensure that a bolt has a prescribed tension when used for connections. If a nut on the bolt is tightened so that the six 3-mm high heads of the indicator are strained 0.1 mm/mm, and leave a contact (Figure 1) area on each head of 1.5 mm“, determine the tension in the bolt shank. The material has the stress-strain diagram shown. (Figure 2) Express your answer to three significant figures and include appropriate units. HA ? Tigure 1 of 2 T = Value Units The unit you entered is not recognized. Review a list of acceptable units No credit lost. Try again. 3 mm Submit Previous Answers Request Answer < Return to Assignment Provide Feedback
3-55: A ring of SAE 301 stainless steel is to be placed on a shaft having a temperature of 20 Celsius and a diameter of 55.200 mm. The inside diameter of the ringis 55.100 mm. To what temperature must the ring be heated to make it 55.300 mm in diameter and this allow it to be slipped onto the shaft?
The standard cross-section for a flat key, which is fitted on a 50 mm diameter shaft, is 16 x 10 mm. The key is transmitting 475 N-m torque from the shaft to the hub. The key is made of commercial steel (oy = 230 N/mm²).if the factor of safety is 3. Determine the length of the key.