The rectangular piece of wood, 51 mm by 183 mm, is used as a compression block. The grain of the wood makes a 31.6° angle the horizontal, as shown in the figure. Determine the largest axial force P (in N) that can be applied safely if the allowable stresses on the plane of the grain is 11.9 MPa for compression. Round off the final answer to three decimal places. 018 shear.png

The rectangular piece of wood, 51 mm by 183 mm, is used as a compression block. The grain of the wood makes a 31.6° angle the horizontal, as shown in the figure. Determine the largest axial force P (in N) that can be applied safely if the allowable stresses on the plane of the grain is 11.9 MPa for compression. Round off the final answer to three decimal places. 018 shear.png

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

NEED ANSWER ASAP The wooden members A and B are to be joined by plywood splice plates that will be fully glued on the surfaces in contact. The clearance between the ends of the members is to be 10 mm, the length of the plywood is L = 361 mm and the width of the wood is W = 151 mm. Find the shearing stress (in Mpa) in the glue if P = 33.6 kN. Round off the final answer to two decimal places.
The lap joint is fastened with four 0.65-in.-diameter rivets. The working stress is 20.72 ksi for the rivets in shear. Find the bearing stress (in psi) on the plates. Assume that the load is equally distributed among the rivets. Round off the final answer to four decimal places. 013.png ... W in. P -in.
2) USE THE METHOD OF SECTIONS TO FIND THE MAGNITUDE AND DIRECTION OF THE FORCE IN BAR CD SHOWN BELOW IN Fig 1.2 D -600lb -800lb B 4 7' 4' H. G 8' 8' Fig 1.2
5 decimal places 1. Determine the outer diameter (mm) of a tubular rod subjected to an axial force of 51 kN if it developed a stress of 21 MPa. Take note that the inner diameter is 3/6 of the outer diameter. 2. Three identical plates of 67 mm wide and 7 mm thick is connected by a square pin with side dimension 17 mm. If the middle plate is subjected to a tensile force of 25 kN, determine the shear stress (MPa) developed in the pin. 3. Two identical plates of 61 mm wide and 5 mm thick is connected by a square pin with side dimension 19 mm. If a plate is subjected to a tensile force of 28 kN, determine the bearing stress (MPa) developed in the plate.
As a part of preliminary design study, the effects of wind loads on a 275 m high building are investigated. The distribution of wind pressure is parabolic as shown. The projected length of the building perpendicular to the paper is 60 m. The wind pressure at the top is 0.60 kPa 0.60 KPa H p=k√x Compute the shear force at the base of the building in KN. a. 6400 c. 6600 b. 6800 d. 6200 Compute the moment at the base of the building in KN-m a. 1,089,000 c. 1,099,000 b. 1,079,000 d. 1,069,000 Compute the shear force at the mid-height of the building in KN. a. 4176 c. 4186 b. 4266 d. 4276
The homogeneous bar ABC is supported by a pin at C and a cable that runs from A to B around the frictionless pulley at D. Find the stress (in psi) in the cable if its diameter is d= 0.57 in and the weight of the bar is 5305 Ib. Round off the final answer to three decimal places. 0002.png D 3 ft 5 ft 5 ft A B
NEED ANSWER ASAP THANK YOU !! A joint is made by gluing two plywood gussets of thickness t = 0.78 in to wood boards. Determine the shear stress for the glue (in psi) if the dimension b = 17.51 in and the applied force is P = 9857 lb. Round off the final answer to three decimal places.
2.5 in. -3 in. A t 1 in. 2 in. 6 in. В 2 in. 2 in. 2 in. ENTER YOUR ANSWERS BELOW AND SHOW ALL YOUR WORK ON PAPER. A steel forging consists of a 6x2x2 -in. rectangular prism and two cylinders of diameter 2 in. and length 3 in. The weight of the rectangular prism is 6.81 Ib. The weight of the cylinders (each) is 2.67 Ib. Calculate: THE MASS MOMENT OF INERTIA OF THE 6x2x2 -in. RECTANGULAR PRISM WITH RESPECT TO THE X- AXIS is Ib-s?/ft THE MASS MOMENT OF INERTIA OF EACH CYLINDER WITH RESPECT TO THE X-AXIS is Ib-s?/ft THE TOTAL MASS M-OMENT OF INERTIA OF THE COMPOSITE SHAPES WITH RESPECT TO THE X-AXIS is Ib-s?/ft
A metal block of cross-section area A and length L is subject to a tensile stress of S. The block elongates by a length of 0.001L. Another block made from the same metal is subject to the same tensile stress. If this block has a cross-section area of 2A and a length of L, determine the elongation of the block. a. 0.004L b. 0.002L c. 0.0005L d. 0.001L
PLEASE WRITE YOUR COMPLETE SOLUTION AND BOX THE FINAL ANSWER. THANK YOU. A piece of wood used as a compression block as shown has a cross-sectional area equal to the shaded area. Determine the safe value of P that can be applied to the block if the compressive stress is limited to 26 MPa, the shearing stress parallel to grain is limited to 5.66 MPa, 6.67 MPa, and 7.76 MPa for 15°, 20°, and 25°, respectively, and the bearing stress between the bearing plate and the wood is limited to 17 MPa. The diameter of the circle is 27 cm. Assume that the area under shear is equal to the cross-sectional area divided by the cosine of the grain inclination.
NEED ANSWER ASAP, THANK YOU A joint is made by gluing two plywood gussets of thickness t = 0.53 inCHES to wood boards. Determine the tensile stress for the plywood (in psi) if the dimension b = 15.73 in and the applied force is P = 7988 lb. Round off the final answer to three decimal places.
A tensile stress is to be applied along the long axis of a cylindrical copper rod that has a diameter of 2.1 mm. Determine the magnitude of the load required to produce a 0.002 mm change in diameter if the deformation is entirely elastic. Answer in N. The modulus of elasticity of copper is 110 GPa and it's Poisson's Ratio is 0.34. Round your answer to 0 decimal places.