The rigid bar is pinned at A and supported by two aluminum rods, each having a diameter of 1 in. and a modulus of elasticity ??? = 10,000 ??? and ?????? = 29,000 ???. The allowable stress of aluminum is 7.8 ksi and steel is 1.7 ksi. If the bar initially vertical, a. Determine the maximum P that can be applied. b. Determine the deformation of steel. c. Determine the deformation of aluminum.

The rigid bar is pinned at A and supported by two aluminum rods, each having a diameter of 1 in. and a modulus of elasticity ??? = 10,000 ??? and ?????? = 29,000 ???. The allowable stress of aluminum is 7.8 ksi and steel is 1.7 ksi. If the bar initially vertical, a. Determine the maximum P that can be applied. b. Determine the deformation of steel. c. Determine the deformation of aluminum.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.4.2P

See similar textbooks

Similar questions

wL+ Smax 8EI
B2-8m RC Beam Sec B-B Sec A-A Sec A-A C1 (0,8x0,8)m Sec A-A- Sec 8-B A Sec A-A- 143.9* Sec A-A Sec A- Sec B-B Sec C-C Sec C-C Soc B-B Sec Sec C-C -3.185m Sac A-A-D 83=4.5m Sec B-B -Sec 8-8 C1 (0,8x0,8)m DBT Figure 2: Plan of Reinforced Concrete Beams Sec A-A -C1 (0.8x0.8)m
There is a statically indeterminate beam in which the horizontal force at the left and right ends (points A and D) is zero, and the vertical force is shown in the figure below, The flexural stiffness of the beam section is constant El: Try to find the slope (Slope) of point B after deformation.
dx csch x (5 + 3 cosh x)
4.5.12 OIC Section Properties Write functions for A, I, c, radius of gyration. Each function works for the three sections below. Example Function name: OICSEC_A() • OICSec_() Etc. 을 + 12 BIP - bhs V, 12(BII-bh) BII -- bha 6/1 - 8
S ( x³ + 4x² ) dx 1. (e –1) dx (e +1) 2.
Problem 6 Determine the force in each member of the trusses. State if the members are in tension or compression. Assume all members are pin connected. Present the results in a final drawing of the truss that shows the value of each member force and a (T) or (C) to indicate the member is tension or compression. 8 ft 25 k D↓ |6ft- 6 ft B 20 k -6 ft 61 E 10 k -6 ft C
Prblm 4c,
fe 1. a b c and d
O 88 130% v - + I Annotate T| Edit Trial expired Unlock Full Version ENGR 263 + A A A T O 4.10 Member AB is the beam under consideration. As shown in the illustration of the loading condition, member AB is an overhanging beam that supports a uniformly distributed roof load of 500 lb/ft. It also carries concentrated loads from a rooftop HVAC unit (4000 lb), an interior hanging display support (2000 lb), and a marquee sign (3000 lb). Marquee overnang Displau SLIPPort II Raof Kiots Ol I W = 500 Ib/Ft A B 4000 b 2000 000 I Steel beam !! I1 3 FE 5 FE - Ft RoOFtop HVAC unit 10 FE 4 Ft Marquee sign< R R2 Steel beam (negligible weight) Free-body diagram Dispiay Support Loading condition
Compute the compressive strength of a WT 12x81 of A992 steel. The effective length with respect to the x-axis is 25 feet 7inches, the effective length with respect to the y axis is 20feet, and the effective length with respect to the z-axis is 20 feet WT12X81 A 23.9 t₁ 1.22 ly 221 d 12.5 k des 1.72 J 9.22 bf 13.0 y 2.70 Cw 43.8 tw 0.705 293
Designation Serial size 457x191 ■ Calculate the design tension resistance of the 457 × 191 × 67 UB. Given information from steel section table (assuming S275): Axis y-y cm³ 1296 67 Elastic modulus Wel Axis Z-Z cm³ 153 Mass per metre kg/m 67.1 Depth of section h mm 453.4 Width of section b mm 189.9 Plastic modulus Wpl Axis y-y cm³ 1471 Axis Z-Z cm³ 237 Thickness Thickness Root of web of flange radius tw tf mm r mm mm 8.5 12.7 Buckling parameter U 0.872 Torsional index X 37.9 10.2 Depth between fillets d mm 407.6 Ratios for local buckling Flange Web Cf/tf Cw/tw dm6 0.705 6.34 Warping Torsional constant lw constant IT cm4 37.1 48.0 Area of section cm² 85.5 Second moment of area Axis y-y cm4 29380 Axis Z-Z cm4 kNm 522 1452 Indicative values for S355 steel Mc.y.Rd Nb.z.Rd* for Lcr=3.5m kN 1600 Radius of gyration i Axis y-y cm 18.5 Axis Z-Z cm 4.12; Designation Serial size 67 457x191