The state of strain at the point on the spanner wrench has components of <= -260 (10). y = 320 (106). Yzy 180 (10-6). (Figure 1) Figure 1 of 1 Select point P on Mohr's circle that represents and point that represents €2. +0 No elements selected -350 -300250 -200 A (-260,90) G R-303.64 -150-100 -50 Q 300 -250- -200 -150- -100 -50 50- 100- 150 200- 250- 1! |! C(300) 50 | Y/2, 10-6- P a D 100 150 200 250 ? 300 350

The state of strain at the point on the spanner wrench has components of <= -260 (10). y = 320 (106). Yzy 180 (10-6). (Figure 1) Figure 1 of 1 Select point P on Mohr's circle that represents and point that represents €2. +0 No elements selected -350 -300250 -200 A (-260,90) G R-303.64 -150-100 -50 Q 300 -250- -200 -150- -100 -50 50- 100- 150 200- 250- 1! |! C(300) 50 | Y/2, 10-6- P a D 100 150 200 250 ? 300 350

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The answer must be wn= sqrt(3g/5b). Solve this without the application of Moments please.
5- B) What do you mean by strain? A strain gauge has a resistance of 157.4 ohms and a gauge factor of 2.7. Find the change in resistance of the gauge for a strain of 0.0017.
For the given state of plane strain, use Mohr's circle to determine the state of plane strain associated with axes x' and y rotated through the given angle 8. Ex=-500μ, &y=+250µ, Yxy = 0, 0 = 13° O (Round the final answers to one decimal place.) The strains are Ex'= Ey₁ = | Vx'y¹=[ H
L,=40mm; L,= 120mm; L=100mm and 0,=65°. Find the possible value of 0, and 0, L,=80mm and 3.
1) A cylindrical rod of constant shear modulus, G is of length L and located between z=0 and z=L. It has a polar moment of inertia given by J=(Jo)/(1-Z/L) and t=-sin(πZ/2L)where Jo is a constant.The boundary conditions are dΦ(o)/dz =0 AND Φ(L)=0 Find Φ(z) and graph (1/GJo)Φ(Z), and (1/GJo)(dΦ(Z)/dz) ?
An 6 mm diameter aluminum rod has lines scribed on it that are exactly 10 cm apart. After a 2.08 kN force has been applied, the separation between the lines has increased to l' = 10.009 cm. 30 cm 10 cm -F l' a. Calculate the stress and strain in the rod. (Express your answer for stress using two significant figures.) |MPa (Express your answer for strain using four decimal spaces.) E = b. To what total length has the rod stretched? (Express your answer using three decimal places.) L final cm
3. At temperature T₁, the two rigidly connected rods just fit the rigid supports. If both sections are identical except for the diameter, prove that the following equations are true when temperature rises to T₂. a. F= b. OAB C. OBC A x(T₂-T₁)лd²E 20 x(T₂-T₁)E 5 9x(T₂-T₁)E 5 -1/2- d B 1/12- d C
Q1 The 45° strain rosette is mounted on a steel robotic am as shown in Figure Ql. The robotic arm is made from steel with Esel = 200 GRA and poison ratio, v= 0.3. The following readings are obtained for each gauge: E=[Y+Z](10“) E = -250(10-) E= -200(10) Here the value of Y and Z depends on the 5th digit and 6th digit of your matric number as shown in Table 1. For example, if your matrix number is DD 070112 gives the value of Y=300 and Z-60: Table 1 5 digit of matric 6* digit of matric number number 250 300 350 30 2 60 3 400 3 90 4 450 120 5 500 150 6. 550 180 7 600 7 210 650 700 240 270 (a) Prove that &= E, and E, = E. Determine the shear strain, yand the normal strain, E, and &. (b) Estimate the in-plane principal strains and the angle associated with the principal strains, and (c) Calculate the principal stress associated with the prihcipal strains in (c). (d)
I need help solving the Mohr's circle for strain finding Point A, the center (C) and the radius (R).
A material is subjected to the following strain system,ex=200x10-6, ey=-56x10-6,yxy=230x10-6. Using graphical method, determine A. The principal strains B. The directions of principal strain axes C. The linear strain on an axis inclined at 50o counter clockwise to the direction of ex Given that young's modulus for the material is 207GN/m2 and the poisson's ratio is 0.27, determine the principal stresses
The 45° strain rosette shown in figure below is mounted on the surface of a thin shell. The following readings are obtained for each gage: ea, eb, and ec .Note that Be is negative. Determine: • Shear strain yxy • Principal strains e1 and e2 · The rotation angle (magnitude and direction) from x-axis to reach the principal orientation. Indicate direction as clockwise or counter-clockwise. epsilon a = 4.50E-04 epsilon k= 2.00E-04 epsilons = -1.00E-04 %3D y а b 45° 45°
The 45° strain rosette shown in figure below is mounted on the surface of a thin shell. The following readings are obtained for each gage: ea, eb, and ec. Note that e, is negative. Determine: • Shear strain yay • Principal strains e1 and e2 • The rotation angle (magnitude and direction) from x-axis to reach the principal orientation. Indicate direction as clockwise or counter-clockwise. epsilon_a = 4.50E-04 epsilon_b = 2.00E-04 epsilon_c = -1.00E-04 y а b 45° 45°