1 4.The steel beam has the cross-Wosection shown in the figure.Determine the largest possibledistributed loadWothat thisbeam can support so that themaxtmum bending stress in theE4mbeam does not exceed the4 mallowablenormalstress,200 mmOallowable = 120 MPa.20 mm20 mm400 mm20 mm200 mm

Answered: Image /qna-images/answer/242df23d-8533-44a0-9f5b-8c0d0a4d4bc3.jpg

The steel beam has the cross- Wo section shown in the figure. Determine the largest possible distributed load Wo that this beam can support so that the maxmum bending stress in the beam does not E4m exceed the 4 m allowable normal stress, 200 mm Tallowable = 120 MPa. %3D 20 mm 20 mm 400 mm 20 mm 200 mm

The steel beam has the cross- Wo section shown in the figure. Determine the largest possible distributed load Wo that this beam can support so that the maxmum bending stress in the beam does not E4m exceed the 4 m allowable normal stress, 200 mm Tallowable = 120 MPa. %3D 20 mm 20 mm 400 mm 20 mm 200 mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter10: Statically Indeterminate Beams

Section: Chapter Questions

Problem 10.4.23P: A cant i levé r b ea m i s supported by a tie rod at B as shown. Both the tie rod and the beam are...

See similar textbooks

Similar questions

Find expressions for shear force V and moment M at x = L/2 of beam BC. Express V and M in term s of peak load intensity q0and be a m length variable L.
The Z-section of Example D-7 is subjected to M = 5 kN · m, as shown. Determine the orientation of the neutral axis and calculate the maximum tensile stress c1and maximum compressive stress ocin the beam. Use the following numerical data: height; = 200 mm, width ft = 90 mm, constant thickness a = 15 mm, and B = 19.2e. Use = 32.6 × 106 mm4 and I2= 2.4 × 10e mm4 from Example D-7
A cant i levé r b ea m i s supported by a tie rod at B as shown. Both the tie rod and the beam are steel with E = 30 x 106 psi. The tie rod is just taut before the distributed load q = 200 lb/ft is applied. Find the tension force in the tie rod. Draw shear-force and bending-moment diagrams for the beam, labeling all critical ordinates.
A beam supporting a uniform load of intensity q throughout its length rests on pistons at points A, C and B (sec figure). The cylinders are filled with oil and are connected by a tube so that the oil pressure on each piston is the same. The pistons at A and B have diameter d1and the piston at C has diameter D2. (a) Determine the ratio of d2to d1so that the largest bending moment in the beam is as small as possible. Under these optimum conditions, what is the largest bending moment Mmaxin the beam? What is the difference in elevation between point C and the end supports?
The fr a me A BCD shown in the heure is squeezed by two collinear forces P acting at points A and D. What is the decrease ê in the distance between points A and D when the loads P are applied? (The flexural rigidity EI is constant throughout the frame,) Note: Disregard the effects of axial deformations and consider only the effects of bending due to the loads P.
The cross section of a composite beam made of aluminum and steel is shown in the figure. The moduli of elasticity are TA= 75 GPa and Es= 200 GPa. Under the action of a bending moment that produces a maximum stress of 50 M Pa in the aluminum, what is the maximum stress xs in the steel? If the height of the beam remains at 120 mm and allowable stresses in steel and aluminum are defined as 94 M Pa and 40 M Pa, respectively, what heights h and h. arc required for aluminum and steel, respectively, so that both steel and aluminum reach their allowable stress values under the maximum moment?
The simply supported joist is used in the construction of a floor for a building. In order to keep the floor low with respect to the sill beams C and D, the ends of the joists are notched as shown. If the allowable shear stress is tallow = 350 psi and the allowable bending stress is sallow = 1500 psi, determine the height h that will cause the beam to reach both allowable stresses at the same time. Also, what load P causes this to happen? Neglect the stressconcentration at the notch.
The bending moment M is applied to the box beam in the x-y plane at the orientation show below. (a) Determine the maximum magnitude of the bending moment M so that the tensile bending stress in the member does not exceed 15 ksi. (b) Determine the angle that the neutral axis makes with the y-axis. (c) The position or positions on the beam where the maximum compressive bending stress occurs given your answer in a. Clearly indicate this on the figure below (also calculate the values) 4 in. B 4 in. M 6 in. 6 in.
The lever must exert a force of P = 3800 Ibs at B as shown. The lever lengths are a = 11 in. and b = 47 in. The allowable bending stress for the lever is 12600 psi. If the lever height h is to be 3.5 times the lever thickness t (i.e., h/t = 3.5), what is the minimum thickness t that can be used for the lever? h Cross section Lever a Answer: t = i in.
Find the shear force and bending moment at points B and D. Note: B lies just to the right of the 150 lbf force and D is just to the right of the bearing at C. The bearing at A is a thrust bearing, while the bearing at C is a journal bearing. 150 lb A Answer: VB = -100 lbf MB = 750 lbf in VD = 75lbf Mp = -750 lbf in I 15 in. B 15 in. C. D 75 lb 10 in.
Q1/ A composite beam is made of wood and reinforced with steel strap located on its bottom side. It has the cross-sectional area shown in fig. if the beam is subjected to a bending moment of M=2kN.m, determine the normal stress at wood and steel. Take Ew=12Gpa and Est=200Gpa. 150mm Wood en 20mm Steel 150mm
The simply supported beam is subjected to the force F = 700 N and the uniform distributed load with intensity w = 150 N/m. Draw the shear force and bending moment diagrams (in your homework documentation) and determine the equations for V(r) and M(x). Take a = 0 at point A. 19 F a Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value a 5.2 m 2.6 m 3.12 m Support Reactions The reaction at A is N. The reaction at D is N. Shear Force and Bending Moment Equations In section AB: V(x)= N and M(x)= N-m. In section BC: v(x)- N and M(x)= N-m. In section CD: V(x)- N and M(x)= N-m. A