The structure shown in the figure consists of three cylindrical supports and an elliptical flat billet. Find the drift force applied by the wind blowing at 80km/h. The ambient air temperature is 20 °C. 100 cm WADE'S BARGIN BURGERS 50 cm 150 cm 3.75 cm 150 cm 15 cm 30 cm 150 cm

The structure shown in the figure consists of three cylindrical supports and an elliptical flat billet. Find the drift force applied by the wind blowing at 80km/h. The ambient air temperature is 20 °C. 100 cm WADE'S BARGIN BURGERS 50 cm 150 cm 3.75 cm 150 cm 15 cm 30 cm 150 cm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 50. In the figure below, the waterline section of a 1500 kN barge is as shown. Its center of gravity…

A: We have to calculate metacentric height against the rolling axis.

Q: QUESTION 1 A woman stands on the bridge beam as shown in Figure 1. The woman's weight is 200 kg. a)…

A: a) Converting kg to N. 200 kg = 200 x 9.81 = 1962 N The type of load acting on the bridge is…

Q: PROBLEM 3: Determine the diameter of a pulley carrying a flexible rope that has a constant angular…

A: Answer We are given Angular acceleration α = 3 rad/s2 Angular velocity ω = 2 rad/s Total…

Q: 1.3) The coefficient of static friction between a concrete block and a surface is 0.8. The block…

Q: The figure shows a uniform 50 kg plank sitting on rough surfaces A and B. The static friction…

A: The given figure is shown below:

Q: water surface 1.0 m 2.0 m

Q: A 10.0-kg box is pulled along a horizontal surface by a force of 40.0 N applied at a 30.0° angle…

Q: Example: Two smooth pipes, each having a mass of 300 kN, are supported as shown. Draw the free body…

A: Given data:- Free body diagram:- A free body diagram is a diagram of a single body or a group of…

Q: A line was found to be 1450.25 m long when measured with a 30-m tape under a steady pull of 6.5 kg…

Q: A block in the following figure is pulled up with a Force 20 +S Nt. The weight of the block is 10…

A: WE HAVE GIVEN FORCE =20+S N WEIGHT OF BLOCKW=10 N CONTACT SURFACE AREA=10CM2 thickness of film=1mm

Q: 6m 5m S.G=0.9 2m 2m 2m 6m 1m, Mercury Water @ 20 degree Hemispherical shape

A: Consider the following figure: Where, FN is force of buoyancy. FW is weight of water displaced.

Q: Determine the magnitude and point of application of the horizontal and vertical compenents of the…

A: Compressive stress is the force that deforms the material in a way that reduces the volume of the…

Q: Calculate the resultant force on triangular window ABC shown in figure and locate its center of…

A: Given: The unit weight of water is 10.08 kN/m3. Consider the figure,

Q: b ▼ 2m 2m 2m 15m a

A: Given:- Coefficient of friction=0.60γconcrete=23.5a=28 mb=25 m Different types of forces acts on a…

Q: A cantilever beam carries a varying load as shown in the figure. If E=200,000 Mpa and Determine the…

Q: In the figure shown, determine the weight that can be carried by the 1.5 kN force acting on the…

A: To determine the weight that the piston can carry. Given, Load acting on the piston (F) = 1.5 kN…

Q: Situation 21. For the built-up shape shown in the figure, determine: А. by = 200 mm %3D oty = 10 mm…

A: As per bartleby guidelines, only 1st 3 parts among multiple parts questions need to be solved.…

Q: Q.05. Under cruising conditions the distributed load acting on the wing of a small airplane has the…

Q: From the figure shown, rigid bars are separated by a roller at C and pinned at A & D. A steel rod at…

Q: A jet of water 25 mm in diameter and having a velocity of 7.62 m/s strikes against a vertical plate…

Q: The system in the figure shows fours applied forces and a 50 kN-m couple, answer the following…

A: Find The line of action of the resultant force is at a perpendicular distance.m from point A

Q: Q1: Determine the magnitude and direction of the resultant forces in figure below? F500 N F- 600 N…

A: resultant magnitude = 454.95 N explanation is given below

Q: A cylinder (2.0 m diameter, 3.0 m long and 25 kN weight) is acted upon by water on one side and oil…

Q: A curved wall ABC is shown in the figure and is 9 ft wide. Compute the resultant hydrostatic force…

A: Given data in question Radius Angle Water 9 ft wide To find out Resultant hydrostatic force And…

Q: For the system shown, the masses of A and B are 55 kg and 135 kg respectively. The coefficient of…

A: Given: Mass on A=55 kg Mass on B=135 kg Friction between B and C= 0.12 Friction between A and B=…

Q: A gate supporting water is shown in the figure. What will be the height of the water required so…

Q: When a 3 Ib weight is placed on the end of a floating wooden beam, the beam tilts at an angle 0= 1.7…

A: Solution Given Data Weight= 3 lb θ=1.70 Dimension=8 inx8 in*10 ft

Q: A: Derive an expression to determine the hydrostatic force and the centre of plane submerged inside…

Q: Determine the following: A) Force due to gravity and buoyant force in Newton B) What is the drag…

Q: A 25-mm diameter shaft with density 7,870 kg/m³ is pulled through a cylindrical bore a shown. Oil…

A: Given :

Q: Example 5.1: The rope exerts a horizontal force on the stationary 180-lb crate. The coefficient of…

A: F = Friction Force Opposing the motion N = Normal Force

Q: 180 Problem: From the figure shown the coefficients of friction are as follows: 0.25 at the floor,…

Q: As shown in Figure B2, a cylindrical steel structure (density p = 8000 kg/m³) loosely sits…

A: When a fluid flows relatively past a body, every differential surface area experiences a pair of…

Q: -Compute the total elongation caused by an axial load of 100 kN applied to a flat bar 20 mm thick,…

Q: The ladder and the person weigh 30 lb and 180 lb, respectively. The center of mass of the 12-ft…

A: Note Since we answer one question at a time so we will answer the first one. Please resubmit another…

Q: Determine the capillary rise (in cm) in a glass tube of radius 0.25 mm that is immersed vertically…

A: Given data : Surface tension (σ)=0.0725 N/mRadius (r)=0.25 mmAssume Angle of contact (θ)=0∘

Q: Example 3: Investigate the stability of a wooden beam, 0.20 m x 0.30m x 10m in dimensions. The beam…

Q: A concrete dam given in the figure has water 13 m deep acting on its vertical sides. The coefficient…

Q: Determine the tension T in the belt needed to overcome the tension of 200 lb created on the other…

A: Given Data: The radius of the collar bushing is r=1 in. The tension applied on the belt is 200 lb.…

Q: A 40-kg packing crate is pulled by a rope as shown with a force P = 200 N. The coefficient of…

Q: A steel wire of cross-sectional area 100 mm2 and length 100m is used to lift a weigh of 2.5 kN at…

A: The cross sectional area of wire, A =100mm2The length of wire, L=100mThe weight used to lift,…

Q: Figure FF shows a scow equipped with a derrick with a boom 5.50 m long. What maximum weight could be…

Q: THE UNIFORM 100-LB PLANK AS SHOWN IN THE FIGURE IS RESTING ON FRICTION SURFACES AT A AND B. THE…

A: TO DETERMINE THE DISTANCE X (from left support A) WHEN THE PLANK WILL START TO SLIDE.

Q: Figure A shows a flatboat hull that, when fully loaded, weighs 150 kN. Parts (b)-(d) show the top,…

A: The flow of fluid includes movement of an unbalanced fluid. As long as unequalled forces are in…

Q: An inclined plane as shown in Fig. is used to unload slowly a body weighing 400 N from a truck 1.2 m…

A: given total weight of body W= 400N coefficient of friction between body and the plank is 0.3

Q: A block of uniform material and length L = 1000 mm, width b = 375 mm, and depth d = 65 mm, is…

A: The length of the rectangular block is l=1 m. The width of the rectangular block is b=0.375 m. The…

Q: Explain force of friction between two bodies. If a wooden block of weight 100 N rests on a…

Q: Given data : Friction force%=120 N Normal force%-200 N Find coefficient of friction

Q: A concrete dam given in the figure has water 21 m deep acting on its vertical sides. The coefficient…

A: Given Data:Coefficient of friction= 0.60 γconcrete=23.5kN/m3a= 26mb=21m

Question

The structure shown in the figure consists of three cylindrical supports and an
elliptical flat billet. Find the drift force applied by the wind blowing at
80km/h. The ambient air temperature is 20 °C.
100 cm
WADE'S
BARGIN
BURGERS
50 cm
150 cm
3.75 cm
150 cm
15 cm
30 сm
150 cm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

SITUATION. A three-legged stool is subjected to the load L as shown. Neglect weight of the stool. 75 75 100 B 325 120 120 120 Dimensions in millimeters Zoom image Determine the vertical force reaction under leg C. 0.533L O 0.166L 0.233L 0.667L
P Flag question A beam shown in figure below, is supported by pin at A and roller at B. Determine the support reaction forces. 20 kN w = 40 kN/m 150 kN-m B- 8 m 3 m Paragraph В I
The loads acting on a 3 mm diameter bar at different points are as shown in the figure: B A 10KN |5kN 2kN 3kN 1m 2m 3m If E will be nearly. (a) 29.7 mm (c) 21.5 mm 205 GPa, the total elongation of the bar (b) 25.6 mm (d) 17.4 mm
SITUATION. A three-legged stool is subjected to the load L as shown. Neglect weight of the stool. 75 75 100 B. 325 120 120 120 Dimensions in millimeters Zoom image Determine the vertical force reaction under leg B 0.667L O 0.233L 0.166L 0.533L
SITUATION. A three-legged stool is subjected to the load L as shown. Neglect weight of the stool. 100 325 120 120 120 Dimenaions in millimeters Q Zoom image Determine the vertical force reaction under leg A. O 0.667L O 0.233L 0.533L 0.166L
A beam has a natural frequency of 1.179 hz and a damping ratio of 5%. It’s subjected to loads that would cause 2.38 mm of displacement if the loads were applied statically. However the loads oscillate at a frequency of 0.844hz. Calculate the maximum displacement.
EXAMPLE (1) A circular bar having 200 mm? area is subjected to axial loads as shown in Fig „Find the value of (P) and the total elongation. Take E=2*10 N/mm?. A В C D 50KN 50kN -lo KN 1M 1M 1M ナ

2. A beam with an inverted T-section is loaded as shown. Determine the following: a. Magnitude of the maximum bending moment and its location relative to point A. b. Rectangular moment of inertia of the beam's cross section with respect to the neutral axis. 10W GIVEN: a. 40mm 20 E 5 KM m 4a 20+0+20+ R₂ 3m BIE B 2m 성 Re
Roundoff your answer to Deflections, locations, forces & Moments: decimal places Slopes Diameters W The cantilever beam is loaded with Pupward concentrated load acting at distance s from the free- end and the distributed load intensity is defined by the equation W = -7x + 63 in kN per meter is loaded from x = 0m (free end) to x = 9m (fixed end) as shown. The beam has the following properties: E = 200 GPa, I = 2x10⁹ mm4 5m 5 decimal places round up to whole number 2 B 3m C fixed Calculate the following using Area Moment Method or Conjugate Beam Method. B.) If the load P is removed and s = 2.00m, 15. What will be the maximum deflection? 16. What will be the maximum slope? 17. If the maximum deflection is to be limited at 10 mm, what diameter of circular beam is required? 18. If the maximum slope is to be limited to 0.20 degrees, what diameter of circular beam is required? 19. If the bending stress at the fixed support is to be limited to 30 MPa, what diameter of circular beam is…
In the figure below, the slope angle theta = 20 degrees and the block weight equals 100 N. which of the following is true regarding the direction of the frictional force between the block and the slope surface? A B Slope angle = 0 Hs = 0.5 W O down slope (parallel to the slope surface and downwards) O up slope (parallel to the slope surface and upwards) O perpendicular to the slope surface O parallel to the slope surface, but could be upslope or downslope depending on the magnitudes of forces A and В
H.W. A circular bar having 200 mm? area is subjected to axial loads as shown in Fig. Find the value of (P) and the total elongation. Take E=2*105 N/mm?. B 50KN P 10kN 50KN 1M 1 M 1 M
A continuous beam with a span of 20m is supported at both ends A and C by a hinged and a roller at B as shown in the figure. The beam does not have the same moment of inertias. E = 200000 MPa and I = 700 x 106 mm4. 60 kN 15 kN /m C A I 21 10 m 5 m 5 m