The value of (NPSH) for a pump is given by the manufacturer as 10 ft. Water is being pumped from a reservoir atminatmospheric pressure at a rate of 30 ft /s to a tank at atmospheric pressure. The water level in the reservoir is 5 ft below thepump. If the total head loss in the suction pipe is 5 ft, is the pump safe from cavitation effects?If a 2-in schedule 40 pipe of 150 m length was used downstream of the pump, what is the power delivered to the fluid? Youmay assume that the friction factor in the pipe is equal to 0.004.

Answered: Image /qna-images/answer/525ba96a-15a0-40be-981b-75b0fc850a3f.jpg

The value of (NPSH)min for a pump is given by the manufacturer as 10 ft. Water is being pumped from a reservoir at 3 atmospheric pressure at a rate of 30 ft /s to a tank at atmospheric pressure. The water level in the reservoir is 5 ft below th pump. If the total head loss in the suction pipe is 5 ft, is the pump safe from cavitation effects?

The value of (NPSH)min for a pump is given by the manufacturer as 10 ft. Water is being pumped from a reservoir at 3 atmospheric pressure at a rate of 30 ft /s to a tank at atmospheric pressure. The water level in the reservoir is 5 ft below th pump. If the total head loss in the suction pipe is 5 ft, is the pump safe from cavitation effects?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. Assume a horizontal shaft handling water at 65 deg C (Pv=2.503 KPa, Density=980.5 m3/kg). The suction nozzle is 4.35 m below the pump centerline and the pressure gauge reading at this point is 221Kpag. Determine the NPSHa if the head loss is 0.82 m. If the NPSHr is 3m less than the NPSHa you got on question number 1, determine the pump suction specific speed at pump rotating at 1800rpm and Q=500gpm
Q1) Figure Ql shows piping system with pump to drive the oil upward from A (P=PA kPa) to B (P=180 kPa) at a mass flow rate of 3 kg/s. Determine type of flow and calculate required pump power. Given data: oil density and viscosity are 891 kg/m³ and 0.29 N.s/m² respectively. Use Hagen Poiseulli equation for loss: he128µQL/(xpgD“) and Power=Qpghr; Triangle geometry: a²=b²+c² Dripe = 3 mm 15 m Pump 20 m Figure O1
Show complete solution and formulas used. Show the schematic diagram too. Calculate the required pipe diameter to avoid cavitation, if the pump delivers Q = 30US gallon/min water from a closed tank, where the pressure (above the water level) is p = 40kPa. The equivalent length of the smoothened concrete pipe on the suction side is 12m while the suction flange of the pump is 8m below the water level. The vapour pressure at the given water temperature is 2.8kPa. The required net positive suction head is NPSHr = 3.2m.
Saturated water at 310K is being pumped from a tank to an elevated tank at the rate of 7L/s. All of the piping is in 5-in. schedule 40 steel pipe. If the 2 fittings used is 90° ell standard long radius, The pump has an efficiency of 80%. Calculate the kW power needed for the pump. * 125 m 12 m -5 1 50 m 5-in. pipe schedule pump Your answer
What is the maximum height the higher reservoir can sit and be filled using a fixed-speed pump with 1-1/4 HP of input and a 57% efficiency rating at 30 GPM of flow? The suction line is 30ft of 1-1/4” schedule 40 steel pipe. The discharge line is 1” schedule 40 steel pipe and is horizontal for 10 ft.
If a pump requires a minimum of 2.75 m of NPSHA, how high can the centerline of the pump be located above the top of an open tank that supplies 27 C water to the pump? The barometer reads an average of 732 mmHg throughout the year. The tank is 1.82 m high. The pipe friction is 0.7 m and the velocity is 1.22 ?/? .
The distribution system requires to lift water to an area with an average elevation of 90 mamsl from the pumping station at 35 mamsl. The area has a demand requirement of 30 MLD and the minimum pressure head requirement is 20 m-head. The pipe which will serve the area is 500 mm with C-value of 90 and length of 3000 m. Determine the following: a) total head loss along the pipe in meter, b) the head of pump required in meter, and c) the power required by the pump with an efficiency of 80% in kilowatt. Note: Theaverage water surface level of the reservoir which supports the pumping station is 5 m.
A centrifugal pump driven by a 120-kW motor rotating at 2400 rpm is used to pump 20°C water in a manufacturing plant. The pump operates against a head of 30 m and has an efficiency of 70%. If this pump is situated 9 m below the level of the source, calculate (Zs)max and determine if the pump is safe from cavitation. Select one: O a. -7.9 m; NOT SAFE O b. -9.7 m; NOT SAFE O c. -7.9 m; SAFE O d. -9.7 m; SAFE
A pump operating at 1750 rpm delivering 500 gpm against a total head of 150 ft. Changes in the piping system have increased the total head to 360 ft. At what rpm should the pump be operated to achieve this new head at the same efficiency?
Water is supplied in a 2-in. dia. pipe at the rate of 2 cfs to a 10-hp, SO-percent efficient pump. Determine the pressure rise if the exit pipe is of (a) 2-in. diameter and (b) 3-in. diameter.
Calculate the power supplied to the pump shown if its efficiency is 75%. Water is at 25 degrees Celsius is flowing at the rate of 50.0 m3/h. The suction linf is a standard DN 100 Schedule 40 steel pip, 15m long. The total length of DN 50 Schedule 40 steel pipe in the discharge line is 200m. The elbows are tight, the entrance to the pipe is flush and the globe valve is completely open. Draw the line of total and piezometric heights.
a pumping station working with a pump head of 25m. the output power of the motor for that pump is 16kw. identify the pump efficiency if the sewarge discharge velocity is 0.27 m/s and the pipe diameter is 250 mm