The vertical U-Section of a water distribution system seen on the drawing is considered. All hydraulic and dimensional data of the flow piece are known as given below. Calculate the Horizontal and Vertical components of the force acting on the flanges connecting the piece to the system. Q₁ = 30 [lt/s], P₁= 200 [kPa], d₁ = 50 [mm] P₂ = 150 [kPa], Q2 = 22 [It/s], Q = 8 [lt/s], d₂ = 100 [mm] 22 = 0,7 10³ [m²] Pa = 100 [kPa], 2₂ P₂ Q1 Р1 Ф d d₁ Q2 ΩΡΩ

The vertical U-Section of a water distribution system seen on the drawing is considered. All hydraulic and dimensional data of the flow piece are known as given below. Calculate the Horizontal and Vertical components of the force acting on the flanges connecting the piece to the system. Q₁ = 30 [lt/s], P₁= 200 [kPa], d₁ = 50 [mm] P₂ = 150 [kPa], Q2 = 22 [It/s], Q = 8 [lt/s], d₂ = 100 [mm] 22 = 0,7 10³ [m²] Pa = 100 [kPa], 2₂ P₂ Q1 Р1 Ф d d₁ Q2 ΩΡΩ

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For the tutorial question, assume the inputs are: A = 0.75 [m] ; B = 1.03 [m] ; C = 0.685 [m] ; U = 33.5 [km/hr]; ANSWER: 1A) In the gradient equation of the keel L(z) = A + B · z; A = 1B) and B = 2) If Re_CR = ρ · U · L_CR; then L_cr [m] = 3A) To determine D_S, one needs first to calculate C_f_l(z). In the equation C_f_l(z) = D / l(z)^(-0.2) + E / l(z); D = 3B) and E =
PROBLEM 2 Determine the internal force of the following members in the structure below. [Select] 1. GI [Select] 2. FH [ Select ] v 3. GH 20 N 40 N 40 N 20 N D 2 m Ao 10 m KOOL Mo NoL 4 m 4 m 4 m 2m -- 2m
. I am planning to perform some volume-flow rate measurements in the Fluid Mechanics Laboratory. For this, I need a volumetric measuring tank (graduated cylinder) and a stopwatch. I considered the volume of the measured tank as 15 gallons and a stopwatch with reaction time as 1/10th of a second (though resolution of 1/1000th of a second). What is the volume flow rate if it takes 5 minutes to fill a 15-gallon of tank? Determine the smallest division to be on the tank in order to estimate the volume flow rate within an accuracy of ± 0.05 gpm.
Analyze the free-body diagram, given the coefficients of static and kinetic friction. Determine whether the block will slide and the net force on the system. static kinetic Hs = 0.25 friction is not shown, but must be incuded in calculations Hk = 0.2 fs,max = 50 %3D fr = W2 [N] slide? friction [N] friction direction | Fnel [N] 40 yes, down-righ 40 up-left v 22 W.-102 W2 W = 200N 50 up-left v (see table) 80 no W = 225N 50 down-righ no 120 18 40 down-righ 160 yes, up-left v 58 40 down-righ v yes, up-left annot be de 200 check answers
As given in the figure, the water flowing into a tank at a constant speed will make the tank in 5 minutes h = It fills up to a height of 3 m. The long side of the rectangular warehouse is 2 m and short If the side is 1.5 m, the water at 30 ° C flowing from the 0.2 m diameter pipe at point A Calculate its average velocity as [m / s] and its flow rate as [kg / s]. (b) Water at 0.5 m / s It flows into the pipe at a constant average velocity. In this framework, h = 3 m deep warehouse The relationship between the time required to fill (t) and the pipe diameter at point A (D) Determine. (Take the width of the warehouse as 1.5 m). Plot the graph of t (minutes) vs.D (m). (D; Let it be located on the horizontal axis as 0.05 m, 0.1 m, 0.15 m, 0.20 m and 0.25 m).
0.8m 1.2m Wale 2m O DE 1.067 kN C O DE= 1.207 kN C O DE 1.139 kN C O DE=0.606 kN C Im Im ||1.5m 1.5m²|| The scissors lift consists of two sets of symmetrically placed cross members (one in front that is shown and one behind that is not shown) and two hydraulic cylinders (front [labeled DE] and back [not shown]). The uniform platform has a mass of 60 kg with a center of gravity at G1. The 85 kg load (center of gravity at G2) is centered front to back. Determine the force in each of the hydraulic cylinde necessary o maintain equilibrium. These are rollers at B and D.
Water is flowing in pipe A as shown in Figure 2. Calculate the pressure [kPa] at point А. Legend: Water sg = 0.82 340 mm sg = 13.6 280 mm 185 mm 65° 150 mm A 152 mm Figure 2
Please
1. The discharge of water, spilled from the spillway of the dam is given by the following formula in the British unit system. = 0.07 B H? Here H shows the water height on the spillway [L]=ft, B shows the spillway's width [L]=ft, Q shows the discharge on the spillway [L³/s]=ft/s. (1 ft=0.3048 m) a. Is|0.07 value a dimensionless(non-dimensional) constant? b. Can this equation be used in other unit systems?
Show diagrams and calculations to support your answer. Suppose you are a group of cadet engineers given by your department manager a “simple” task of choosing an appropriate flow meter to install in a straight horizontal pipeline of the given specifications: Nominal diameter: 6 inches Schedule Number: 40 Material of Construction: steel Water is to flow through the pipeline within the range of 600 to 625 gal/min at a temperature of 27°C. You have the following choices in terms of the flow meter: [a] a venturi meter [b] an orifice meter [c] a rotameter [d] a commercial flowmeter of your choice, other than the above-mentioned ones Which would you recommend? Tips: [1] Base your choice on the following criteria: [1.a] pressure loss due to the presence of the flow meter [1.b] relative cost (and ease) of installation [1.c] relative cost of equipment
Problem Statement: A flow of water passes through a pipe and out of a nozzle as shown in the figure. The pipe has diameter di = 6.8[cm], the nozzle diameter is d2 3.7(cm]. A manometer h2. placed in the free jet as shown has a reading of h2 3.8(cm). Answer the following: Free d1 d2 Find the height h1 of the first manometer. ст Find the velocity of the liquid exiting the nozzle at (2). m/s Find the velocity of the liquid in the pipe at (1). m/s Find the pressure in the pipe at (1). kPa
3. Draw the shear and moment diagrams for the beam below. Be sure to label all local maxima and minima, locations of zero shear and moment, and the degree of all curves (linear, quadratic, or cubic). The reaction forces are given at roller A and pin B so a FBD is not required for this problem. Note: Small error may be expected due to rounding of support reactions. 50 lbs/ft V [lbs] M [lb-ft] A, = 381 lbs 4 ft A 120 lbs teateat 2 2 50° 2 ft B₂-77 lbs B B, -12 lbs