Please answer E using this info The Zener diode shown in the circuit has a current I₂ = 8 mA, at8.8 V and resistance rz = 25 2. The 15 V power supply has 20%fluctuation. The Zener diode is rated at 500 mW maximumpower. AV is the fluctuation in the output voltage Vo.Determine the following when Iz = 10 mA flows through theZener diode as shown. Determine the(a) V. (at nominal supply voltage)(b) IRL(c) I(d) R(e) AV(f) Maximum Zener diode current Imax+15V± 3V10 mAR18R₁1 ΚΩVoRL ⒸProblem 2V₂0= √₂-√₂ x 1₂ = 8.8v-25 × 8mA = 8.6v.XIRL = Volemax= V₂ *Izmax.:V₁ = V₂ + I₂ √₂ → 8.8 + 10 ×0.025 =9.05✓REAVO**********3I= I2 +IRL =R= V15I19.05=9.051.KR500mw >S9.05MA500mW =8.856.81 MA787-210+ 9.05 = 19,05 mA

Answered: Image /qna-images/answer/61e65684-7225-465d-96fb-9b58504257ec.jpg

The Zener diode shown in the circuit has a current I₂ = 8 mA, at 8.8 V and resistance rz=25 2. The 15 V power supply has 20% fluctuation. The Zener diode is rated at 500 mW maximum power. AV, is the fluctuation in the output voltage Vo. Determine the following when I₂ = 10 mA flows through the Zener diode as shown. Determine the (a) V. (at nominal supply voltage) (b) IRL (c) I (d) R (e) AVO (f) Maximum Zener diode current Imax +15V 3V 10 mA R 2 Vo 1 KRL

The Zener diode shown in the circuit has a current I₂ = 8 mA, at 8.8 V and resistance rz=25 2. The 15 V power supply has 20% fluctuation. The Zener diode is rated at 500 mW maximum power. AV, is the fluctuation in the output voltage Vo. Determine the following when I₂ = 10 mA flows through the Zener diode as shown. Determine the (a) V. (at nominal supply voltage) (b) IRL (c) I (d) R (e) AVO (f) Maximum Zener diode current Imax +15V 3V 10 mA R 2 Vo 1 KRL

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Consider a junction diode has dc biased current at operating point ID=0.8 mA. A sinusoidal voltage is superimposed on the VD such that the peak-to-peak sinusoidal current id(t) = 0.05ID. Find the value of the applied peak-to-peak sinusoidal voltage vd(t).
C. In the circuit shown below the knee current for the ideal Zener diode is 10 mA Calculate the minimum value of load resistance RL in order to maintain 5 volts across the load resistance RL 2. WW-
A single phase – half wave controlled rectifier with freewheeling diode is supplying a load consistingseries connected a resistor and an inductance from a 70.7V (RMS), 50Hz sinusoidal AC source.The firing delay of the thyristor is 90° and the load values are R=10Ω, L=0.1 H. Define the loadcurrent expression and draw the load current by calculating for first two periods. And calculate theaverage values of the load voltage and current.
0:- Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. c) If 100uf capacitor parallel with the resistor, calculate the ripple is connected factor I O o D
For the circuit shown in Figure 2, sketch the output voltage (across the load 2.2 KN resistor) and the load current (through the load 2.2 Kn resistor). Sketch the diode voltage (across the diode D1) and the diode current (through the diode DI). The input V. is sinusoidal with maximum amplitude (peak) of 100 V and frequency of 700 Hz. The diode DI is a Silicon diode. The sketches have to be at least for two cycles of the input. D1 2.2 K2 Vi
Suppose we have a 10-V-peak sinusoidal voltage source. Draw the diagram of a circuit that clips off the part of the sinusoid above 5 V and below -4 V. The circuit should be composed of ideal diodes, dc voltage sources, and other components as needed. Be sure to label the terminals across which the clipped output waveform vo(t) appears.
Consider the circuit with three diodes and a AC input, as shown below: D2 R1 D1 D3 R2 Assume that the input AC voltage is Ttsin(100TTT). You may consider the diodes to be ideal. mean voltage generated across resistor R2 is (assuming current direction to be from AC so into R1, through diode network, and through R2 from top to bottom): O a. 0.5V Ob. -0.5V O c. 1V O d. OV
Two ideal diodes are placed in series, pointing in opposite directions. What is the equivalent circuit for the combination? What is the equivalent circuit if the diodes are in parallel and pointing in opposite directions?
4. For the circuit shown in the figure below uses a transformer of 230V/12V-0-12V and all diodes are Ge find the following, RL-3.3k2. The name of the circuit is ........ Current through the load is............The DC output voltage is............ Draw the input & output wave forms ✈ ellel eetee CT D₂ DE www R₂
3: Using silicon diode design a clamper that will produce output V,-20Sin wt+10 (v) when the input voltage is Vo=20Sin wt-10 (V).Draw the circuit diagram and the input and output signals. 4:The 6-V zener diode has a maximum rated power dissipated of 690 mw.Its reveres current must be at least 3mA to keep it in breakdown. Find a suitable value for Rs if V; can vary from 9v to 12v and Ri. can vary from 5000 to 1.2KO.
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V ams 5OHZ İL-DC =05A RL VL-DC =20V
In the circuit below, sinusoidal input voltage with a peak value of 10V is applied. Calculate the current flowing through the diodes D1 and D2 by drawing the waveform of the output voltage. (Both diodes will be considered ideal and Vc=5V).