Three cables are attached to the bracketas shown.Replace the forces withequivalent force-coupleExpress results in Cartesian vector form.systematA.75 mm1000 N50 mm50 mm1200 N30700 N60100 mm100 mmE(150 mm, -50 mm, 100 mm)Figure 1

Consider the position O=0,0,0, A=0,100,0, B=75,100,50C=75,10,-50, D=100,0,0, E=150,-50,100…

Three cables are attached to the bracket as shown. Replace the forces with an A. equivalent force-couple system Express results in Cartesian vector form. at 75 mm 45 1000 N 50 mm 50 mm 1200 N 30 700 N 60 100 mm 100 mm E(150 mm, -50 mm, 100 mm) Figure 1

Three cables are attached to the bracket as shown. Replace the forces with an A. equivalent force-couple system Express results in Cartesian vector form. at 75 mm 45 1000 N 50 mm 50 mm 1200 N 30 700 N 60 100 mm 100 mm E(150 mm, -50 mm, 100 mm) Figure 1

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3. For the shaded area shown in the figure below, determine the following: a. The area of the shaded area in square millimeters b. the x coordinate of the centroid in millimeters c. the y- coordinate of the centroid in millimeters. 400 e 200 200 400 All units in mm 300 300 PSD323- Principles of Steel Design 4. The tee section is made up of a 30mmx150mm flange and a 30mmx160mm web. Determine the properties of a section(MOI, section modulus, radius of gyration) 150 mm 30 mm A, 'p A N.A. d, 30 tnm wuI 09t
Activity 3 Problem Set Question Locate the plastic centroid of the section shown below. Dimensions are in meters. Your reference axes are the leftmost and topmost edge of the flange. 2Ø12 fy = 350 MPa 0.650 1 Ø12@150 stirrups 5Ø25 fy = 390 MPa 0.250 0.450 0.150
Plz solve within 30min I vill give definitely upvote and vill give positive feedback thank you sir plz
Assume that the clamp shown has been tightened on wooden planks being glued together until P= 360 N. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. P' The neutral axis is 50 mm a Determine the location of the neutral axis mm above D. A. B section a-a. 10 mm Section a-a ➜ 4 mm D | 41 20 mm mm
In (Figure 1), F = 750 N. Point B is located at the midpoint of the rod. Figure 6 m 4 m D F 4 m B 3 m 4 m 1 of 1 Part A Determine the component of F that act along rod AC. Express your answer to three significant figures and include the appropriate units. F|| = Submit ▾ Part B for Part A for Part A undo for Part A redo for Part A reset for Part A keyboard shortcuts for Part A help for Part A FL= Value Determine the component of F that act perpendicular to rod AC. Express your answer to three significant figures and include the appropriate units. Submit Units Request Answer for Part B for Part B undo for Part B redo for Part B reset for Part B keyboard shortcuts for Part B help for Part B Value Units Provide Feedback Request Answer
AT beam is constructed from a square cross-section section and a rectangular cross-section of the same length. The cross-section dimensions of the sections are as follows:- Bottom Square Section 25x25mm Top Rectangular Section 47x25mm (width x depth) Figure Q12 shows the cross-section arrangement of the plates. Calculate the Neutral Axis location as measured from the base of the T beam. State your answer in millimetres to 1 decimal place. X mm X mm Y mm X mm Zm
substitute: C=9, E=22, H=12 A built-up section is shown in figure (a) Determine the thickness "t" of asis the horizontal plate if Centroid is "IE])"x"(H]"mm located at C mm from the horizontal reference axis (x-axis), and (b) Find the moment of Inertia of the Section - 300 mm x 50 mm with respect to the given x-axis (use calculated t from problem a).
■ Determine the maximum T of the structural arrangement as shown below (S275). T I 25 25 25 25 25 12 TYPICAL 20 mm THK PL 50 30 30 30 50 T
The linkage is made of two pin-connected A-36 steel members, each having a cross-sectional area of 1.3 in² ( Figure 1) Figure 2 ft B 1511--1511- Part A Determine the magnitude of the force P needed to displace point A 0.035 in downward Express your answer in kilopounds to three significant figures. Ψ—| ΑΣΦdivec P Submit Request Answer < Return to Assignment Provide Feestrack ? kip
PROBLEM 1: A bracket fixed at point O shown on Figure SRB 001 is subjected to a multiple force F1, F2, and F3 a point A. Determine the following: 0 a) The equivalent forces of x-component. b) The equivalent forces of y-component. c) The resultant of the force system. d) The angle of inclination of the resultant with respect to x-axis. e) The equivalent couple in Newton-meter acted on point O. F₂ = 500 N 3 0.2 m -0.4 m F₁ = 600 N 35° F3 = 800 N 0.1 m B Figure SRB 001 0.3 m
The truss is made from A992 steel rods each having a diameter of 0.9 in .(Figure 1) Part A Determine the vertical displacement of joint C. Express your answer to three significant figures and include the appropriate units. ? (Ac)vert = Value Units Figure Submit Request Answer < Return to Assignment Provide Feedback C 60° 60° 12 kip 6 ft B
А L B 425 mm C 1,000 mm V P A steel bar (1) and an Aluminum bar (2) are connected to a rigid angle ACD. Assuming: • Steel [E = 200 GPa] bar (1) is 6mm x 40mm x 600mm long. • Aluminum [E = 70 GPa] bar (2) is 10mm x 40mm x 600mm long. Poisson's ratio, v = 0.35 • A distance L of 500mm. a)Determine the force P (in kN) required to stretch the Aluminum bar by 1mm. Enter the force, P, into the d21 answer box (in kN, 3 sig digs). b) Determine the final width and thickness of the Aluminum bar. (1) Your Answer: