TOP The assembly shown has pin support at E and roller support at V. A steel rod is connected at M and it is perpendicular to arm VM. The pin support at E is under single shear and is also made of steel. Determine the maximum force P that can be applied to the assembly. Show the free body diagram. Show all calculations. Steel Properties: Jallow = 36 ksi Tallow = 22 ksi E = 29,000 ksi M 3/4" diameter steel rod Rigid 5 ft 1" diameter steel pin Single shear E 5 ft V 4 ft

TOP The assembly shown has pin support at E and roller support at V. A steel rod is connected at M and it is perpendicular to arm VM. The pin support at E is under single shear and is also made of steel. Determine the maximum force P that can be applied to the assembly. Show the free body diagram. Show all calculations. Steel Properties: Jallow = 36 ksi Tallow = 22 ksi E = 29,000 ksi M 3/4" diameter steel rod Rigid 5 ft 1" diameter steel pin Single shear E 5 ft V 4 ft

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.5.26P: A horizontal bracket ABC consists of two perpendicular arms AB of a length 0.75 m and BC of a length...

See similar textbooks

Similar questions

A horizontal bracket ABC consists of two perpendicular arms AB of a length 0.75 m and BC of a length 0,5 m. The bracket has a solid, circular cross section with a diameter equal to 65 mm. The bracket is inserted in a friction less sleeve at A (which is slightly larger in diameter), so it is free to rotate about the r0 axis at A and is supported by a pin at C Moments are applied at point C M{=1.5 kN -m in the x direction and A/3 = L0 kN-m acts in the — z direction. Considering only the moments Mxand M2, calculate the maximum tensile stress t, the maximum compressive stress crc* and the maximum in-plane shear stress Tmax at point />, which is located at support A on the side of the bracket at mid-height
Repeat Problem 11.3-9. Use two C 150 × 12.2 steel shapes and assume that E = 205 GPa and L = 6 m.
-7 Repeat Problem 2.3-5, but n include the weight of the bar. See Table I-I in Appendix I for the weight density of steel.
Repeat Problem 6.2-1 but now assume that the steel plate is smaller (0.5 in. × 5 in.) and is aligned with the top of the beam as shown in the figure.
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
Compare the angle of twist 1 for a thin-walled circular tube (see figure) calculated from the approximate theory for thin-walled bars with the angle of twist 2 calculated from the exact theory of torsion for circular bars, Express the ratio 12terms of the non-dimensional ratio ß = r/t. Calculate the ratio of angles of twist for ß = 5, 10, and 20. What conclusion about the accuracy of the approximate theory do you draw from these results?
A simplified diagram of a racing cars suspension and wheel is used to design the bars and pins. The force that the suspension must withstand can be considered to be a vertical force, F = 1.5 kN, acting vertically upwards at B. Calculate the minimum radius of the bars AB and BC if the maximum allowable stress oalow= 80 MPa. Also, calculate the minimum radius of the pin at A if this pin is in Double Shear and the maximum allowable shear stress Tallow = 50 MPa 25° A B Wheel
Given:a. the force in BD=25KNb. vertical reaction at point C=-10KNc. horizontal reaction at point C=15KNd. resultant of reaction at point C=18.0KNe. allowable tensile (normal) stress in member BD =83.33MPaf. the allowable shear stress in the pin at C =72.7MPaPlease help me solve for:1. What is the required cross-section area and minimum thickness t of member BD?2. What is the required SHEAR cross-section area at point C?3. What is the minimum diameter for the pin at C?(Solve for a value with the combination of mm and N)
The dimensions of the block given the loading condition are a = 40, b = 30 and c = 6 mm. Calculate the maximum load p that can be applied without creating stress in the x direction and the extension rates in other directions at this moment.(Modulus of elasticity: 200Gpa, Poisson's ratio: 0.3)
The lap joint is fastened with four 3/5 in-diameter rivets. The allowable normal stress in the plates is 30 ksi, allowable shearing stress is 24 ksi for the rivets and 28 ksi for the plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets. Include the necessary FBDs showing the involved internal forces in the exploratory sections. Your solutions are invalidated without the required FBDs.
each sold bar has a 36N/m weigh If the 1:In the following arrangement of structur allowable shear stress in pin C is 16 Mpa calculate the pin diameter at A. If the diameter of bar is (10 mm) what is the bearing stress on bar AB. 36N/M 2m im Im 2m
Solve for the force in BD, vertical reaction at point C, horizontal reaction at point C, resultant of reaction at point C. What is the allowable tensile (normal) stress in member BD? What is the allowable shear stress in the pin at C? What is the required cross-section area for member BD? What is the minimum thickness t of member BD? What is the required SHEAR cross-section area at point C? What is the minimum diameter for the pin at C? (Solve for a value with the combination of mm and N)