Answered: Two channel are welded at the tip of…

Two channel are welded at the tip of their flanges to 16.5 mm form a box column Properties of single channel: A = 5690 mm² d = 254 mm be = 77 mm t = 11 mm 17 mm- %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A wide flange and a channel have the following properties. They are attached as shown. -Wide Flange- A 18,400mm² dm 470mm Ix= 726x106 ly= 93.6x106mm4 tw = 12mm Fv bolt=100MPa diameter of bolt = 16mm www -Channel- A = 6430mm² Ix ly = 3.4x106 x = 20mm tw== 10mm u 131x106mmª Fb channel = 118MPa Fb WF= 138MPa > Find the moment of inertia of the section. 970.622 ➤ Determine the moment capacity of the section. 452-72 Determine the safe uniform load that the beam could carry over a 9m simple span. 45." Determine the spacing of bolt. 179-35
Select all zero-force members in the truss shown below. Check the box for zero- force members 3m 12 m, 8 @ 1.5 m O DE LK EP OHF O BC O BM O EF O OM O CD O BN LO O DK FI O co O O O O O O 0 0 O 0
Part 2: Identify the read forces 4m 11 ang 600 4m 60 60 4m 10KN Rea'd: All member forces (use methorl of joints)
The built-up section shown below is fastened together by passing two 10 mm diameter rivets through the top and bottom plates into the flanges of the beam. Each rivet will withstand 11.8 kN in shear. Determine the required spacing of the rivets along the length of the beam if it carries a shearing force of 199 kN. 12 mm x 180 mm plates (2) I IPE I 400x180x642.2 steel 10 mm rivets
A steel beam having a span of 14 m. carries a dead load concentrated load Pp = 60 kN at its midspan. The beam is laterally supported at its span. Properties of the wide flange section. rts - 104.39 mm ho - 338.08 mm Jo -1.69 x 10^6 Cw - 4.3 x 10^12 d=356.11 mm tf = 18.03 mm tw - 11.18 mm Sx - 2343 x 103 mm rx = 155.96 mm ry - 93.98 mm Sy = 818 x 10^3 mm Zx = 2573 x 10^3 mm Zy= 1239 x 10^3 mm Fy = 345 MPa Iy = 151 x 10 mm Lp=3.98 Lb=14m Lr=12.98 Cb=1.14 Determine the safe concentrated live load that the beam could support at the center based on its design strength
Situation 8: Light grade steel channels are used as purlins as shown in the figure. The top chords ofthe truss are inclined at 1V:4H. The trusses are spaced at 6m on center. The purlins are spaced at 6m on center. The purlins are spaced at 1.20m on centers. The roof are as follows: Dead load including roof materials 720MPA 1,000MPA 1,440MPA Live load Wind load Wind pressure coefficient Windward Leeward 0.20 0.60 Channel properties Section modulus, S Section modulus, S Weight 6.19x10*mm 1.38x10*mm %3D 79/m The allowable bending stresses are Ex = 207MPA and E = 207MPA. Assume that all the loads pass through the centroid of the channels. 1.20 1.20 EEÉËÈEE Sagrod 21. Which of the following mostnearly gives the maximum bending stress, fex, for the dead and live load combination (DL+LL)? a. 127.11MPA c. 132.20MP. b. 151.14MPa d. 169.48MPA 22. Which ofthe following most nearly gives the maximum bending stress, f, for the dead and live load combination (DL+LL)? а. 169.48MPа c. 127.11MPA d.…
Determine the force of the members for the space truss shown in the figure. Joints A and B are supported by ball-and-socket while Joint C is supported by short link along z-axis. Indicate whether member is tension (T) or compression (C). 2m y Sm Az By BX Bz PAR Ax CSXScanned with Ca canner a SISU KN 15m 1 2117
ure B 2m2 m C -2 m D 4 m 500 N 700 N 2 of 2 Part B Identify the zero-force members in the truss shown in (Figure 2). Check all that apply. 000 CD DE CG CF FG BC BG DF AG EF AB Submit Provide Feedback Request Answer
Design the panel marked by (X), Column sections 350 mmx 350 mm. LL = 3 kN/m? fe = 28 MPa fy= 420 MPa 7.50 7.50 3.75 m. m. m. -h, m IT 0.50 0.35 6.0 m w 0'9 ---- h m+ 0.50 0.35
2. Determine the adequacy of the clip angle connection shown. The allowable stresses are 100 MPa for shearing, 220 MPa for bearing, and 140 MPa for tension for the seat angle and the rivets. 45 kN 220 mm I 16 65 32 150 150x100x16 clip angle 20 mm o rivets 16 100
figure A 2m """" B 2 m C ** 2 m E 4 m D 700 N 500 N 2 of 2 > ▼ Part B Identify the zero-force members in the truss shown in (Figure 2). Check all that apply. EF FG ODF П П П □ DE AB ВС BC AG CG CD BG CF Submit Provide Feedback Request Answer
E CH2- Resultant paf - Adobe Acrobat Pro Estended Fle Edit View Document Comments Forms Tools Advanced Windew Help 2/87 If the resultant of the two forces and couple M passes through point O, determine M. 150 mm 60° mm 30 M, = M-400x 0.15cos30-320x0.3 0 M = 148 Nm CCW 320 N 160 400 N mm Example : Replace the three forces acting on the bent beam by a single equivalent force R. Specify the distance x from the point O in which the line of action of R passes. 200 N 160 N ahid hamoodi •..