Two torque as shown are applied on a compound shaft of aluminum segment and a steel. Determine the maximum permissible value of T subjected to the following conditions: T, s 90MPA, Ta S 65MPA_, and the angle of rotation of the free end limited to 11°. Use GS = 84 GPa and Ga = 27 Gea 75 mm Aluminum Steel Bf 50 mm 2 m 1.5 m

Two torque as shown are applied on a compound shaft of aluminum segment and a steel. Determine the maximum permissible value of T subjected to the following conditions: T, s 90MPA, Ta S 65MPA_, and the angle of rotation of the free end limited to 11°. Use GS = 84 GPa and Ga = 27 Gea 75 mm Aluminum Steel Bf 50 mm 2 m 1.5 m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.8.3P: A solid circular shaft AB of diameter d is fixed against rotation at both ends (sec figure), A...

See similar textbooks

Similar questions

A solid circular shaft AB of diameter d is fixed against rotation at both ends (sec figure), A circular disk is attached to the shaft at the location shown. What is the largest permissible angle of rotation 0max of the disk if the allowable shear stress in the shaft is Tallow? [Assume that a >b. Also, use Eqs. (3-50a and b) of Example 3-9 to obtain the reactive torques.]
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the adequacy of both the pipes. In the test, the pipe structure is fixed at A, a concentrated torque of 500 kN - m is applied at x = 0.5 m, and uniformly distributed torque intensity t1= 250 kN m/m is applied on pipe BC. Both pipes have the same inner diameter = 200 mm. Pipe AB has thickness tAB=15 mm, while pipe BC has thickness TBC= 12 mm. Find the maximum shear stress and maximum twist of the pipe and their locations along the pipe. Assume G = 75 GPa.
Let's consider a solid circular shaft subjected to the torque loads as shown Determine the minimum required diameter "D" if the shaft is made of a material having a yielding shear stress Ty = 100 MPa, for a factor of safety FS = 2. The polar moment of inertia of a solid circular cross-section is given by Jr.R¹/2. 300 mm B 600 mm 100 N.m 500 N.m 600 mm 400 N.m
If the permissible shear stress of a solid shaft is of 70MPa, the torque angle between two cross sections separated 2.5m does not exceed 3°, the applied torque is of 1400N.m and G=11Gpa a. Determine the required diameter in function of the shear stress b. Determine the required diameter in function of the angle of twist
A solid brass shaft is loaded as shown below by two torques TB- segments are LAB = 700 mm and LBC 600 mm. A dBc = dAB mm LAB mm B Com dBC For brass, G = 41 GPa. Neglect the effect of any stress concentrations. LBC Determine the smallest diameters dAB and dBC for which an allowable shear stress of 50 MPa is not exceeded. Express each diameter as an integer in units of mm. dAB To 1100 Nm and Tc = 300 Nm. The lengths of the two Determine the magnitude of the total angle of twist in the shaft caused by the two applied torques for the diameters found previously Express your result in units of radians with five decimal places of accuracy. PAC = rad
Consider the compound shaft KDQC which is composed of a 300 mm long solid rod DQC (G = 35 GPa) fitted snuggly (up to a length of 200 mm) into a 600 mm (G = 63 GPa) long pipe KDQ. The rod has a diameter of 170 mm and the pipe has an outer diameter of 210 mm with a wall thickness of 20 mm. Two concentrated torques are applied at Q and C with magnitudes and directions as shown. Note that the end K of the pipe is fixed to a wall. ø210mm 20mm K 2.5T T 400mm 200 100 mm mm If the maximum allowable twist at any section of the entire compound shaft is 0.0005 rad, determine the following: 1. The polar moment of inertia of pipe KDQ and of the of rod DQC. ×108 mmª Jpipe Jrod x107 mm4 2. The internal torques in pipe KDQ and rod DQC at section DQ in terms of the unknown applied torque T: TpQ.pipe TpQ,rod 3. The maximum allowable value of T considering the given maximum permissible angle of twist for the entire shaft (express your answer in kNm): T kNm 4. The corresponding maximum shear stress…
Consider two steel shafts CFG and HJ of diameters 50 mm and 70 mm respectively as shown in fig. The shaft CFG is supported at two bearings, while shaft HJ is fixed at 'H' and supported by bearings at 'J. Determine the torques T 1 and T 2 if the twisting at gears C and G is required to be 0.05 rad. Take E=205GPA, G=70GPA 600 mm 75mm 600 mm 50mm 800mm G. T2
A hollow aluminium shaft of 80 mm outer diameter & 60 mm inner diameter is rotating @ 5 Hz when constant 120 KW is applied. Use the following: G(alum)=28 GPa, a=1.80 m, b=0.80m & L=2.60 m. Assumed that the angle of twist is constant.The torque "T2" developed at right fixed support at B is ___KN-m 3.82 2.64 0.48 1.18 5.03
a solid shaft is transmitting 1 mw at 240 rpm determine the daimeter of shaft exceed the mean of torque 20% take maximum shear alloy stress as 55mpa
2. The diameters of the solid shafts are: AB is 0.6 in, A B D BC is 0.75 in. and CD is 0.9 in. The applied torques are: TĄ = 400 in lb, Tg = 1200 in Ib, Tc = 500 in İb. Determine the maximum shear stress in each of the three shafts. TA TB Ans: TmaxAB = 9431 psi, TmarBC = 9658 psi, TmaxCD = 9082 psi Te Fixed to wall