Answered: Use D flip-flops to design a mod 5… | bartleby

Electric Motor Control

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Related questions

Question

Use D flip-flops to design a mod 5 counter. The counting sequence is 000->110->101->111-
>001->000...
(a) Draw the state diagram using 5 states; (b) Use CBA to represent the three bits of the state
and write the state transition table; (c) Use K-maps to derive minimum sum-of-product
equations for the flip-flop inputs.

Expert Solution

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

Use D flip-flops to design a mod-16 binary down counter, whose counting sequence is 1111->1110->1101->1100->1011-> … ->0000->1111…. Derive the logic expressions for the D inputs of the flip-flops and draw the circuit diagram.
Explain and design a mcd-6 co:unter using J-K flip flop. [
Q#01: The schematic shown in figure below is for Divide_by_11, a frequency divider, that divides clk by 11 and asserts its output for one cycle. The unit consists of a chain toggle-type flip-flops with additional logic to form an output pulse every 11th pulse of clk. The asynchronous signal rst is active-low and drives Q to 1. Develop and verify a model of Divide_by_11. Vcc 20LSB Q2 03MSB clk clk clk clk clk rst rst rst rst wl w2 clk QB cik_by_11 rst rst
F4 Using two flip-flops and basic gates, construct the circuit of the given state diagram below. Provide the following: State Table, Flip-flop equations, Circuit Diagram. Follow correct label names: Q0, Q1 – prev/present states D0, D1 – D-FF names X – input Y - output
4- Draw the output waveform if the signal shown in Figure below is applied to inputs of J-K Flip-Flop. Q is initially Low. HIGH CLK- CLR nnnnnnn CLK PR CLR
Design a 3-bit counter that counts the following sequence: 7,5, 3. 1.0.7, 5. 3, 1, 0, 7. etc. Using the sequential design technique that starts from a state diagram, draw the state table. minimize the logic. and draw the final circuit. The outputs of logic circuit are 2 = Qo Q1. I, = Qo.Qi + Qo.Qi, Io = Qo.Q2, Cont2 = Qj Q2 Cont1 = Qu Q2. Cont0 = Q2 Qo.Q1. h = Qo.Qi + Qo.Q1, Io = Qo Qz Cont2 = Q, Q2 Contl = Qo Q2 Cont0 = Q2 Qo Qı Ij = Qo.Q, + Q».Qı, Io = Qo. Q2. Cont2 = Qj Q2. Contl = Qo.Q2. Cont) = Q2 L = Qo.Qı. I¡ = Q. Qj + Qu Q Io = Qv.Qz Comt2 = Q, Q, Contl = Q Q2 Cont0 = Q2 !! fefsto How much will be per-product cost and th
Write the next-state equations for the flip-flops and the output equation. (b) Construct the transition and output tables. (c) Construct the transition graph. (d) Give a one-sentence description of when the circuit produces an output of 1. Q2 D2 Q1 T1 CLK Figure 4
Two edge-triggered J-K flip-flops are shown in figure below. If the inputs are as shown, draw the Q output of each flip-flop relative to the clock, and explain the difference between the two. The flip-flops are initially RESET. CLK CLK -C CLK- K K (b)
c) d) Explain the different between sequential circuit and combinational circuit. a) Identify input conditions necessary in order to set, reset and toggle the JK flip flops in Figure Q3d(i) and Q3d(ii). Clock QUESTION 4 J K Q व Figure Q3d(i) Clock S R Clock Convert the SR flip-flop in Figure Q4a to behave like JK flip-flop. ā Figure Q4a a J K Q ā Figure Q3d(ii)
We want to design a circuit to detect prime numbers.The input of the circuit is a 4-bit binary number and the output is a single bit and should show one when the number is prime and zero otherwise.B. Implement the circuit using a 4× 1 multiplexer and combinational logic gates.C. Implement the circuit using only one decoder and one OR gate. What is the size of the decoder you use?
Design a 3-bit up/down counter using positive edge-triggered T flip-flops. Provide a respective timing diagram to justify the design. Show all the relevant working (state table, state diagram, K-maps, state equations, and final circuit diagram). An up/down counter has two inputs say x, y, and a clock signal. The output should increase by 1 if x = 1 and y = 0 on each rising edge of clock and decrease when x = 0 and y = 1 on each rising edge of clock. When x = y, the output should neither increase nor decrease on each rising edge of clock.
Complete the design process using full encoding and D-flip flop for the the function described by the follow state diagram and draw the schematics.

SEE MORE QUESTIONS

Recommended textbooks for you

Electric Motor Control

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Electric Motor Control

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

SEE MORE TEXTBOOKS