Water flows through the 40-mm-diameter pipe assembly such that the velocity at A is 6 m/s and the pressure is 200 kPa The assembly and the water within it have a mass of 54 kg. Assume that the flow is steady and the water can be considered as an ideal fluid. -2 m- 40 mm 6 m/s 2 m Part A Determine the a component of force exerted at the support C, assuming there is no support resistance at A and B. Express your answer to three significant figures and include the appropriate units.

Water flows through the 40-mm-diameter pipe assembly such that the velocity at A is 6 m/s and the pressure is 200 kPa The assembly and the water within it have a mass of 54 kg. Assume that the flow is steady and the water can be considered as an ideal fluid. -2 m- 40 mm 6 m/s 2 m Part A Determine the a component of force exerted at the support C, assuming there is no support resistance at A and B. Express your answer to three significant figures and include the appropriate units.

Residential Construction Academy: House Wiring (MindTap Course List)

4th Edition

ISBN:9781285852225

Author:Gregory W Fletcher

Publisher:Gregory W Fletcher

Chapter1: Residential Workplace Safety

Section: Chapter Questions

Problem 12RQ

See similar textbooks

Similar questions

rubber pad A Valyrlan stoel plate В alumbnum ber L- 1.5t A-1 in E- 10 000 ku a- 12.8 x 10* "F X.
The copper pipe (G - 45GPA) has an outer diameter of 50mm and an inner diameter of 30mm, It is fxed at A and three torques are applied to it as shown. Solve the rotation of the free end with respect to the fixed end. A 200mm 250mm 3. 30 N-m 300mm 20 N m 80 N-m O 0.00125rad O 0.00112rad O 0.00104rad O 0.00237rad
STRENGTH OF MATERIALS A boiler is constructed of 9mm thick steel plates that are fastened together at their ends using a butt joint consisting of two 9mm cover plates and rivets having a diameter of 10mm and spaced 60mm apart as shown. If the stream pressure in the boiler is 1.38MPa, determine (a) the circumferential stress in the boiler's plate apart from the steam, (b) the circumferential stress in the outer cover plate along the rivet line a-a, and (c) the shear stress in the rivets. 60 mm 0.78 m
22: The springs connecting with a rigid weightless bar as hown. The stiffness of beam (Kb) is 5 kN/m and the tiffness of all the springs (K) are 4 kN/m. Find the natural requency for the system. K Imm 444 3m K
The force applied at the handle of the rigid lever causes the lever to rotate clockwise about the pin B through an angle of 2°. Calculate the average normal strain developed in each wire. The wires are unstretched when the lever is in the horizontal position. A T 200 mm 200 mm B -300 mm- 200 mm D 300 mm E
A hollow steel tube (1) with an outside diameter of D1 and a wall thickness of t1 is connected to a solid aluminum rod with a diameter of d2. The system is supported by a restraint at A and is subjected to loads at B and C.[D1 = 56 mm, t1 = 1 mm, d2 =d3 = 48 mm, E1 = 210 GPa, E2 = E3 = 55 GPa, P1 = 28 kN, P2 = 17 kN, L1 = 295 mm, L2 = 195 mm, L3 = 260 mm] Determine the movement of joint B with respect to support A?in mm Determine the movement of joint C with respect to support A?in mm Determine the movement of joint D with respect to support A?in mm
Quizs- Replace the loading system by an equial ent resultant force and Couple moment acting at Point o. fi=l00 N Mc:75 Nm 0:3m 200 0-5 m 0.4m
P F 600 mm 2P 2P A E C 400 mm B D - The assembly consists of two 12.05 mm-diameter A992 steel rods AB and CD, a 20-mm- diameter 6061-T6 aluminum rod EF, and a rigid bar AEC. If P = 11.52 kN - determine the displacement of F. - Find the displacement of point F if the system is subjected to a change in temperature AT = 9.5 C. Only consider the change in temperature.
The A-36 steel rod has a diameter of 53 mm and is attached firmly to the rigid supports at A and B when the initial temperature is at 80°C. If the temperature becomes 18°C and an axial force of 209 kN is applied to its center, determine the reaction at A (kN). α = 12x10-6 m/(m°C); E = 200 GPa and L=0.57m. Your final answer should have two decimal places.
Proposed Exercise No. 03 Find the resultant force, point of application and thebending moment of the system in the figure:
Fagure O 2. A steel rod of 20 mm diameter passes centrally through a copper tube 40 mm external diameter and 30 mm internal diameter. The lube is closed at cach end by rigid plates of negligible thickness. The nuts are tightened lightly home on the projected parts of the rod. If the temperature of the assembly is raised by 60 "C, calculate the stresses developed in copper and steel. Take E for steel and copper as 200 GN/m and 100 GN/m and a for steel and copper as 12 10 per "C and 18 x 10" per "C. stress is the middle
3 m- -2 m- B C- www 2 m D A The system shown above is in static equilibrium. Which of the following statements regarding particle equilibrium at point D is true? a) The sum of the forces in the x-direction must equal zero b) The sum of the forces in the x'-direction must equal zero c) Both a) and b) d) None of the above (not enough information)