We examined the common source amplifier shown in the figure in the 5th experiment. The measurements made on this circuit are given below. Find thegate voltage based on measurements.Şekilde gösterilen ortak source yüikseltecini 5 deneyde-ineelemiştik. Bu devre üzerinde yaprlan ölçümler aşağıda veritmiştir. Ölçümlere göre yategeritimini butunuz.Circuit parameters and measurements / Devre Parametreleri ve ölçümlerVDD = 12 V, VGs = 1.65 V, Vps = 2.07 V, Rp = 3.1 kQ, Rs = 1 k2R1RDVDDM2GR2RSa. 3.58 VO b. 5.05 VO. 4.56 VO d. 4.07 VO e. 3.10 V수

Given: VDD = 12 V VDS = 2.07 V VGS = 1.65 V RD= 3.1 K OHM We need to calculate the…

We examined the common source amplifier shown in the figure in the 5th experiment. The measurements made on this circuit are given below. Find the gate voltage based on measurements. Şekilde gösterilen ortak source yükseltecini 5 deneyde incelemiştik. Br devre üzerinde yaprlan ölçümler aşağıda verilmiştir. Ölçümlere göre yate geritimini butumuz. Circuit parameters and measurements / Devre Parametreleri ve ölçümler VDD = 12 V, VGs = 1.65 V, Vps = 2.07 V, Rp = 3.1 kQ, R = 1 k2 R1 RD VDD M2 R2 RS O a. 3.58 V O b. 5.05 V O C.4.56 V O d. 4.07 V O e. 3.10 V 수

We examined the common source amplifier shown in the figure in the 5th experiment. The measurements made on this circuit are given below. Find the gate voltage based on measurements. Şekilde gösterilen ortak source yükseltecini 5 deneyde incelemiştik. Br devre üzerinde yaprlan ölçümler aşağıda verilmiştir. Ölçümlere göre yate geritimini butumuz. Circuit parameters and measurements / Devre Parametreleri ve ölçümler VDD = 12 V, VGs = 1.65 V, Vps = 2.07 V, Rp = 3.1 kQ, R = 1 k2 R1 RD VDD M2 R2 RS O a. 3.58 V O b. 5.05 V O C.4.56 V O d. 4.07 V O e. 3.10 V 수

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q-2: Explain the saturation of a transistor. Find the given unknowns for the figure below. a. Rc. b. Rg c. Rp. d. VCE e. V Also find the voltage V, at cutoff. 12 V 2 mA Rc 7.6 V V B-80 024 V Q-3: Define Lso and lao, How are they related? Find the following f le corresponding to V = +750mv and Va = +5V
We examined the common source amplifier shown in the figure in the 5th experiment. The selection criterion of the input capacitance is Xcin = 0.1Rin: Calculate the required input capacitance value, Cin , if an input signal with a frequency of 2 kHz is applied. Şekitde gösterilen ortak source yükseltecini 5. deneyde incelemiştik Giriş kapasitesinin seçim kriteri Xcin - 0.1Rin dir. 2 kHzlik giriç sinyali için gerektt tapasite, Cm değerini hesaplayınız. Circuit parameters / Devre Parametreleri R1 = 53 k2, R, = 17 k2 R1 RD Cout Vout D VDD M2 Cin G Vin R2 RS cs O a. 74.19 nF O b. 86.55 nF O c. 49.46 nF O d. 61.82 nF O e. 43.28 nF
The circuit shown below was used as a current source in a LED lighting application, and voltage quantities given below were measured for this circuit. Calculate the collector current, Ic ? en ınlatma veulam -năidaki gerilım ...ilmüstür ....iini anlavinız l-? Measurements: VRc = 1 V, VRb = 0.80 V, VRE = 0.65 V, VCE = 7.95 V, v2= 3.47 V
Assume VRE 0.7 V and B-50 for the transistor in the circuit shown in the figure. For VCE = 2 V, the value of Rg is RB m B +12 V www Rc- 5 k C E VCE
Q.) Figure below divider bras amplifier Circuit. Givent the model Parameter : gm = 5o mS emitter (CE) Voltage BJT hibrid- TT Shows a Common riT: 6 Kr and to %3D : 00 +Vc. RI C2 Tooks touf RL Vo ihe 200 RE TCE Vs 20 a Draw the Ac eQuivalent at low Freauency Circuit Zi and b.) Determine inPut impedance at mid FreaUincy OutPut imPedance Z0 c.) Calculafe two low Cut -oFF FreQuen Cies FLC1 and FLC2 Ci and E2 respectively Such as due to the exterda al capacitors
1. Estimate and sketch the output signal, Vout showing its proper relationship to the input signal, Vin for the circuit given below [Show you analysis steps]. 20V Vin 20V 2K 2 7 Vin 6 Vout 3 3K 1K -20V 1K
Q2) for the amplifier shown in Figure 1) Determine the voltage gain (Av) and the current Gain (Ai) 2) Determine The input and output resistance 3) Determine The output voltage Vout 4) Draw The Ac load line 5) Draw the AC equivalent circuit 6) Determine the maximum input voltage (Vi(p-p)) for maximum output voltage (Vo(p-p)) without distortion. HH Vi-20 mv RB 56 kQ +₁ D B = 50 - 10 V HH RE 1kQ Vou RL • 10 Ω ww11
1. Define line regulation. 2. Define load regulation. 3. The input of a certain regulator increases by 3.5 V. As a result, the output voltage in- creases by 0.042 V. The nominal output is 20 V. Determine the line regulation in both % and in %/V. 4. If a 5.0 V power supply has an output resistance of 80 m2 and a specified maximum output current of 1.0 A, what is the load regulation? Give the result as a % and as a %/mA.
II- 1) Draw the circuit of a V-l converter and derive an expression for the output current in terms of input voltage. 2) Draw the neat diagram of analog multiplier using log-antilog amplifiers and explain its operation.
Use the following circuit to design an oscillator of 5 kHz output. The amplifier used in this oscillator is multistage C.S. with source resistance amplifier. The design must be with minimum No. of stages. Use the following FET parameters Id=2mA, gm=2.5 ms and rds = 40kN. Use VDD = 24V L R Vo Vi
(b) For a digital-analog converter, sketch a five-stage ladder network using 10 k2 and 20 kQ. (c) What is the % resolution of the ladder network found in part (b)? (d) With a reference voltage of 32V for the ladder network found in part (b), calculate the output voltage for an input of 11101.
Design an transistor amplifier with a total voltage gain of 40. The signal source has a 10 kohm impedance. The load is 5 kohms. Please show all work.