What is the height difference reading on the U-Tube? What is the height difference reading on the U-Tube? *1. Consider a low speed subronic wind tunnel with acontractionarea ratio for the nozzle. If the flow in the test section is at gstondard seo level conditions with a velocity of 30 meters per vec,Calculate the height difference in a U - tube mercury manometer withone side connected o the nozzle inlet and the other to the test3 19/msection. Pg= 1.36 x100.21 m0.05 m0.22 m0.11 mO 0.34 mO 0.39 m

Answered: Image /qna-images/answer/776c8397-8f39-4134-95be-90205d29f697.jpg

1, contractior 1. Consider a low speed subronic wind tunnel with a area ratio for the no2zle. If the flow in the test section is at g stondard seg level conditions with a velocity of 30 meters per vec, Calculate the height difference in a u - tube mercury manometer one side connected to the nozzle iniet and the other to the test 19/m² section. Png = 1.36 x10

1, contractior 1. Consider a low speed subronic wind tunnel with a area ratio for the no2zle. If the flow in the test section is at g stondard seg level conditions with a velocity of 30 meters per vec, Calculate the height difference in a u - tube mercury manometer one side connected to the nozzle iniet and the other to the test 19/m² section. Png = 1.36 x10

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

At a point in a pipe that lay flat ノ water in the pipe flows at a speed of 9.0 mls and has 6-40x 104 Pa a gaoge pressure is Find the gauge pressure at point 2 of pipe that lower than the first point 8.0 m and the cvoss - se ctional| area of the pipe is double of first point . Answer [1.52x105 Pa]
Simulation of laminar gas flow in the pipe with Ansys Fluent Task: 1. Calculate velocity distribution in y axis at inlet and outlet of the pipe. Submit it as a chart. 2. Calculate velocity distribution over the pipe length. Submit it as a chart. Figure. pipe geometry L, m = 16 R, m= 0.15 Inlet velocity, m/s= 0.08 Gas= Oxygen Need proper solution like pdf file, don't need steps by steps. If you can can do it through ansys fluent. Write proper solution on word file or pdf.
Answer this ASAP plz Air enters a pipe with a diameter of 3 cm and a length of 17 m with a speed of V1 = 75 m/s, pressure P₁ = 600 kPa and T₁ = 60 °C and a friction factor of 0.025. Count: a. V2, P2, T2 and po2 at the end of the pipe. b. What is the additional length of the pipe that causes the outflow to be sonic.
A bicycle tire is fi lled with air at an absolute pressure of169.12 kPa, and the temperature inside is 30.0 °C. Supposethe valve breaks, and the air starts to exhaust out of the tireinto the atmosphere (pa = 100 kPa absolute and Ta =20.0 °C). The valve exit is 2.00 mm in diameter and is thesmallest cross-sectional area of the entire system. Frictionallosses can be ignored here; one-dimensional isentropicflow is a reasonable assumption. (a) Find the Machnumber, velocity, and temperature at the exit plane of thevalve (initially). (b) Find the initial mass flow rate out ofthe tire. (c) Estimate the velocity at the exit plane using theincompressible Bernoulli equation. How well does thisestimate agree with the “exact” answer of part (a)? Explain.
In order to measure the speed of the ambient air at atmospheric pressure, a Pitot tube is used, in which water is the gage fluid.. It is known that the ambient air speed is 25 meters per second, when the air temperature is 40 degrees. Celius. Calculate what the differential manometer reading in the pitot tube would be?
her of partic Fluid Flow /Liquid of density 1200 kg/m² throgh a pipe of 50mm inte intemal dimeter an orifice, lo mm in dimeter is fitted in the life and differential Pressure Shwn on amercury manometer is 0-1 m. assuming the leads the manometer are filled with the flowing fluid, calculate @ the mass flow fate of fluid flowing the approximate drop in pressure. caused by the orifice in KN/m² pe of 50 mm in d differential the flowing flu ifice in kN/m the density bartle wers c the coefficient of discharge ugybe taken as 0-61 and the density of mercury is 13,550 kg/m³
Calculate the available net positive section head NPSH in a pumping system if the liquid density p 1200 kg/m'. The liquid dynamic viscosity u 0.4 Pa.s, the mean velocity a= 1 m/s, the static head on the suction side z = 3m, the inside pipe diameter di, = 0.0526m. the gravitational acceleration g = 9.81 m/s, and the equivalent length on the suction side EL, = 5.0 m. The liquid is at its normal boiling point. Neglect entrance and exit 1 losses.
The pipe flow in figure is driven by pressurized air in the tank. What gage pressure (P1) is needed to provide a water flow rate (60 m/h) take (v = 1.15*10 m2/sec).If the (P1 =700Kpa) and the fluid specific gravity is (0.68).estimate the viscosity of the fluid if the flow rate is ( 27 m/sec). 30 m Smoxoth pipe: d = 5 cn Open jet 80 m 10 m - 60 m 86
A venturi meter, shown in Fig. designed constriction whose pressure difference is a mea- sure of the flow rate in a pipe. Using Bernoulli's equation for steady incompressible flow with no losses, show that the flow rate Q is related to the manometer reading h by is a carefully 2gh(PM – p). A2 VT- (D/D;)4 where py is the density of the manometer fluid. 2
The question is: Calculate the velocity of sound propagating in water at 20 degrees C. Assume that the bulk modulus of water K = 2.2 X 109 Pa. I have a= square root of (K/p) I'm coming up with 1485 m/s. The answer is supposed to be 1461 m/s. What am I doing wrong.
For the velocity profile shown find 1.The total displacement ,D(in): 2.The average speed,S(in/s):
Reynold's number of 11090 is obtained for a certain value opening in a shut off valve experimentjexercise 1), when water flows through a pipe of diameter 23 mm. The viscosity of water is 1.14 x10-Nm Find the velocity of flow for this valve opening in m/s=