In the vapor-recompression evaporator shown in Figure P24.27, the vapor produced on evaporation is compressed to a higher pressure and passed through the heating coil to provide the energy for evaporation. The steam entering the compressor is 98% vapor and 2% liquid, at 10 psia; the steam leaving the compressor is at 50 psia and 400°F; and 6 Btu of heat are lost from the compressor per pound of steam throughput. The condensate leaving the heating coil is at 50 psia, 200°F. (a) Compute: The Btu of heat supplied for evaporation in the heating coil per Btu of work needed for compression by the compressor. (b) If 1,000,000 Btu per hour of heat is to be transferred in the evaporator, what must be the intake capacity of the compressor in fts of wet vapor per minute? Compressor Heoting Coil Figure P24.27 Condensate

In the vapor-recompression evaporator shown in Figure P24.27, the vapor produced on evaporation is compressed to a higher pressure and passed through the heating coil to provide the energy for evaporation. The steam entering the compressor is 98% vapor and 2% liquid, at 10 psia; the steam leaving the compressor is at 50 psia and 400°F; and 6 Btu of heat are lost from the compressor per pound of steam throughput. The condensate leaving the heating coil is at 50 psia, 200°F. (a) Compute: The Btu of heat supplied for evaporation in the heating coil per Btu of work needed for compression by the compressor. (b) If 1,000,000 Btu per hour of heat is to be transferred in the evaporator, what must be the intake capacity of the compressor in fts of wet vapor per minute? Compressor Heoting Coil Figure P24.27 Condensate

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. A vacuum refrigeration system consists of a large insulated flash chamber kept at low pressure by steam ejector which pumps vapor to a condenser. Condensate is removed by condensate to an air vent. Warm return water enters the flash chamber at 13°C, chilled water comes out of the flash chamber at 5°C Vapor leaving the flash chamber has a quality of 0.97 and the temperature in the condenser is 320C. For 350 kw of refrigeration (a) How much chilled water at 5°C does this system provide? (b) How much make-up water is needed? (c) How much vapor must the steam ejector remove from the flash chamber?
Steam enters the steam-generating unit at a pressure of 20 bar and dryness of 0.96 and leaves at the same pressure at a temperature of 350°C. Mass flow rate of steam is 5 kg/s. Find the percentage increase in volume (%) due to drying and superheating.
A single effect evaporator is used to concentrate 10 000 kg / hr of tomato juice from 5% total solids to 30% total solids. The juice enters the evaporator at 15 ° C. The evaporator is operated on Steam (80% quality) at 143.27 kPa. The vacuum in the evaporator allows the juice to boil at 75 ° C. The specific heat of the dilute material is 4.1 kJ / (kg ° C) and the concentrate product is 3.1 kJ / (kg ° C). Count it (a) Steam demand rate =kg / hour. b. Steam economy when condensate temperature is released at 75 ° C. = (kg of water evaporated / kg of steam)
A steam condenser receives 10 kg per second of steam with an enthalpy of 2570 KJ/kg. Steam condenses into liquid and leaves with an enthalpy of 160 KJ/kg, if cooling water passes through the condenser with temperature increases from 13oC to 24oC. Calculate the cooling water flow rate in kg/sec. Show conversion of units pls
9. When developing a certain power, the specific fuel con- sumption of an internal combustion engine is 0-255 kg/kWh (brake) and the mechanical efficiency is 86% Calculate (i) the indicated thermal efficiency, and (ii) the brake thermal efficiency, taking the calorific value of the fuel as 43-5 MJ/kg. If 35 kg of air are supplied per kg of fuel, the air inlet being at 26°C and exhaust at 393°C, find (iii) the heat energy carried away in the exhaust gases as a percentage of the heat supplied, taking the specific heat of the gases as 1-005 kJ/kg K.
3.) An ammonia compressor operates at evaporator pressure of 316.02 kPa and a condenser pressure of 1557 kPa. A twin-cylinder compressor with bore to stroke ratio of 0.85 is to used at 1200 rpm. The actual volumetric efficiency is 92% and compression and mechanical efficiency is 78% and 80% respectively. For a cooling capacity of 25 TR, (a) the sketch the p-h diagram labeling the evaporating and condensing temperature and pressures (b) define the all properties of ammonia taken from saturation table. Determine (c) the quantity of cooling water in the condenser in kg/min if the increase in temperature is 8°C, (d) the bore and stroke expressed in cm and (e) the size of the driving motor in hp. Given: h2 = h at 1557 kPa and s2 = s1 1695 kJ/kg
1) Water vapor with a flow rate of 20000 kg / h enters the condenser of a power plant at a pressure of 20 kPa and a dryness degree of 95 percent. In the condenser, there is heat transfer to the river water flowing through the pipes. The temperature rise of the river water is limited to 10'C to prevent thermal pollution. Since the state of the water at the condenser outlet is saturated liquid at 20 kPa pressure, what should be the flow rate of the cooling water.
1. Moist air enters a refrigeration coil at 89 F dry-bulb temperature and 65 F thermodynamic wet bulb temperature at a rate of 14oo cu ft per min. The surface temperature of the coil is 55 F . If 3.5 tons of refrigeration are available, find the dry bulb and wet bulb temperatures of the air leaving the coil. Assume sea level pressure.
Indonesia Inggris A single effect evaporator was used to concentrate 8000 kg / hr of tomato juice from 5% total solids to 30% total solids. The juice enters the evaporator at 25 ° C. The evaporator is operated on Steam (85% quality) at 143.27 kPa. The vacuum in the evaporator allows the juice to boil at 75 ° C. The specific heat of the dilute material is 4.1 kJ / (kg ° C) and the concentrate product is 3.1 kJ / (kg ° C). Count it (a) The rate of demand for steam? b. Steam economy if condensate temperature is released at 75 ° C.?
Steam is delivered to turbine at 5.4 MPa and 600 degree C. Before condensation at 31 degree C, steam is extracted for feed water heating at 0.6 MPa. The turbine exhaust is 60 degree C. the required values of some state point properties are tabulated below. 7. Determine the quality of steam at the condenser inlet.
QI: An R-134a refrigeration system produces 10 ton of refrigerating effect at the evaporating temperature -10°C and the condensing temperature of 40°C.The absolute pressure measured at the inlet and outlet of evaporator are 2.0 bar and 1.7 bar, respectively. Considering there are no superheat and sub cooling effects, calculate the following parameters with or without a drop of pressure in the evaporator: (i) Refrigerating effect (ii) Mass flow rate (iii) Power requirement in kW/TR (iv) COP
steam enters the steam generating unit at a pressure of 20 bar and dryness of 0.96 and leaves at the same pressure at a temperature of 350°C. Mass flow rate of steam is 5kg/s. Find the percentage increase in volume (%) due to drying and superheating.