Write a program in assembly language for the 8085 microprocessor to send one byte of data located at the memory address (3000H ) using SOD at a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz . When sending the required byte, you must adhere to the following: The two high bits of the start bits(1 1) must be sent, after that the data bits are sent, after that the low bit of the stop bit (0) is sent. The following flowchart will help you. The solution must be integrated and include the calculation of the baudrate delay time

Write a program in assembly language for the 8085 microprocessor to send one byte of data located at the memory address (3000H ) using SOD at a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz . When sending the required byte, you must adhere to the following: The two high bits of the start bits(1 1) must be sent, after that the data bits are sent, after that the low bit of the stop bit (0) is sent. The following flowchart will help you. The solution must be integrated and include the calculation of the baudrate delay time

Name: Q1- Write a program in assembly language for the 8085 microprocessor t
Uploaded: 2024-03-20T06:51:23.000Z
Channel: Bartleby
Description: Q1- Write a program in assembly language for the 8085 microprocessor to send one byte of data located at the memory address (3000H ) using SOD at a baud rate of 1200.Information: The 8085 processor operates at a frequency of 3.072 MHz . When sending

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter2: Introduction To Systems Architecture

Section: Chapter Questions

Problem 2VE: A(n) __________ is a storage location implemented in the CPU.

See similar textbooks

Similar questions

Q1- Write a program in assembly language for the 8085 microprocessor to send one byte of data located at the memory address (3000H) using SOD at a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz. When sending the required byte, you must adhere to the following: The two high bits of the start bits must be sent, after that the data bits are sent, after that the low bit of the stop bit is sent. The following flowchart will help you. The solution must be integrated and include the calculation of the baud rate delay time Transmit Set up Character Bit Counter • Send Start Bit No Wait Bit Time Get Character in Accumulator Output Bit Using Do Wait Bit Time Rotate Next Bit in Do Decrement Bit Counter Is It Last Bit? Yes • Add Parity if Necessary Send Two Stop Bits Return (a)
Q1- Write a program in assembly language for the 8085 microprocessor to receive 10 bytes of data via the SID and store it at the memory address (3000H to 3009H) using a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz. When you receive each byte of the required bytes, you must adhere to the following: The bits of two high bits will be received at the beginning of the reception (start bits), after that the data bits will be received, after that the low bit of the stop bit will be received (stop bit). The following flowchart will help you, but you should notice that this flowchart deals with one byte, and you are required to deal with 10 bytes The solution must be integrated and include the calculation of the baudrate delay time Of+CD!HID+[00 Yes SIDATA Read SID Start Bit? Wait for Half-Bit Time Set up Bit Counter Wait Bit Time Read SID Save Bit Decrement Bit Counter All Bits Received? Add Bit to Previous Bits Go Back to Get Next Bit Return IMUNI
Q1- Write a program in assembly language for the 8085 microprocessor to send 10 bytes of data located at the memory address (3000H to 3009H) using SOD at a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz. When sending each of the required bytes, you must adhere to the following: The two high bits of the start bits must be sent, after that the data bits are sent, after that the low bit of the stop bit is sent. The following flowchart will help you, but you should notice that this flowchart deals with one byte, and you are required to deal with 10 bytes. The solution must be integrated and include the calculation of the baudrate delay time Transmit No Set up Character Bit Counter Send Start Bit Wait Bit Time Get Character in Accumulator Output Bit Using Do Wait Bit Time Rotate Next Bit in Do Decrement Bit Counter Is It Last Bit? Yes Add Parity if Necessary • Send Two Stop Bits Return (a)
Q2- Write a program in assembly language for the 8085 microprocessor to receive one byte of data via the SID and store it at the memory address (3000H to 3009H) using a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz . When receive the required bytes, you must adhere to the following: The bits of two high bits will be received at the beginning of the reception(start bits 1 1 ), after that the data bits will be received, after that the low bit of the stop bit will be received (stop bit 0 ). The following flowchart will help you. The solution must be integrated and include the calculation of the baudrate delay time
Q1\ 1- Write a program in assembly language for the 8085 microprocessor to send 10 bytes of data located at the memory address (3000h) using SOD at a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz. And two high pulses must be sent before each byte (start bits) and one low pulse after each byte (end bits). You can use this flowchart, but you should notice that this flowchart deals with one byte, and you are required to deal with 10 bytes Transmit No Set up Character Bit Counter Send Start Bit Wait Bit Time Get Character in Accumulator Output Bit Using Do Wait Bit Time Rotate Next Bit in Do Decrement Bit Counter Is It Last Bit? Yes Add Parity if Necessary • Send Two Stop Bits Return (a)
In .assembly programming language, write a program that rotates the value in register A right by 1 bit. Rotating right is similar to shifting right, except that the excluded bit is inserted at the front
An-Najah National University Department of Computer Engineering Microprocessors (10636322) Assignment # 1 Answer the following: 1- Write an 8086-assembly program that reads only vowels (a, e, i, o, u) from the keyboard (other characters are not excepted) and store them in a character array of 10 bytes long. Vowels entered after the array is full should be discarded. The program should stop reading characters when a 'S' is entered. When the 'S' character is entered, the program should output a new line, followed by the contents of the character array, with a space character between each vowel. 2- Write an assembly code to sort a word array of 50 numbers in ascending order. 3- The perfect number is defined as an integer which is equal to the sum of its divisors. Example: 28 is perfect number because 28 = 1+2+4 +7+ 14. Write an inline assembly e function that will takes an integer number as parameter and check whether it is a perfect number or not. Use the function in complete program. 4-…
Please in assembly to 8086 processor and registers is 16 bit please write an assembly code to fill the memory with the multiple of tens as following:o The first row of memory multiple of A (10 in decimal)oand the second row multiples of 14 (20 in decimal) and so on till 46(100 in decimal)********* . (Note that the length of each row is 16 byte)After executing the code display the content of the memory using:For each question usef range to fill the buffer by your name. for me my name needs 12letter so i use the range from 400 to 40C
Make a quadruples address code out of the statement below: A = - A * (A + B ) - (B – C) / D
0001 = Load AC from memory 0010 = Store AC to memory 0101 = Add to AC from memory 0011 = Load AC (the accumulator register) from an I/O device 0111 = Store AC to an I/O device With these instructions, a particular I/O device is identified by replacing the 12-bit address portion with a 12-bit device number. Remember that a number ending with a small ‘h’ means the number is a hexadecimal number. What is the hexadecimal string that expresses the following instructions? Load AC from memory location 62h. Add the contents of memory location 451h to AC. Store AC to memory location 8h. Store AC to I/O device number 8h.
Code required in mips assembly language not a c code required Write a MIPS procedure that takes as its two parameters the starting address of a (zero-terminated) string, and a character c, and removes all instances of the character from the string. Also, write a main program to test your procedure. Your main program should input a string from the user (you can assume that the string will be at most 40 characters, not including the zero byte delimiter), and then prompt for input of a character c. If the character c that the user inputs is the newline character (ascii code 10), your program should terminate. Otherwise, your program should invoke your procedure, output the modified string, and then prompt for input of another character to be removed from the string, continuing in this manner until the input character is the newline character.
LIST P = 16F877AUsing INCLUDE "P16F877A.INC" and PWM (Pulse Width Modulation), write the microprocessor code that enables the fan to operate at 80% if the button on the 5th bit is pressed, and 30% if the button on the third bit is pressed.