Z y 0.3m 4.25 KN 5 kN 0.4m 100 KN 100 KN 3.0 kN m 0.1m 2 kN 200 KN 2001 This is a stainless steel beam with a circular cross section and a diameter of 7 centemeters. Calculate the reations at the fixed support and draw the bending moment, axial load, torque, shear force diagrams each with equaitions work shown.

Z y 0.3m 4.25 KN 5 kN 0.4m 100 KN 100 KN 3.0 kN m 0.1m 2 kN 200 KN 2001 This is a stainless steel beam with a circular cross section and a diameter of 7 centemeters. Calculate the reations at the fixed support and draw the bending moment, axial load, torque, shear force diagrams each with equaitions work shown.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.11.5P: A square tube section has side dimension of 20 in. arid thickness of 0.5 in. If the section is used...

See similar textbooks

Similar questions

A simply supported beam of hollow rectangular cross section is 100mm deep and 60mm wide with a wall thickness of 10mm. The beam has a span of 6m and carries a load as shown . Neglecting the weight of the beam draw a bending moment diagram and calculate the maximum bending moment. And determine the maximum bending stress in the material.
find the maximum value Mmax of the bending moment
Derive the formula for the bending stress of a beam with a rectangular cross section and triangular cross secrion. Thank you
A simply supported beam is shown. The maximum bending moment is at B. Use the method of sections to determine the moment at B. Then determine the required section modulus needed for an allowable bending stress of 24 ksi. Verify that two L4x3 angles placed as shown will support the loading based on the angle thickness you select using Appendic C. Ans: Ms = 4350 Ib-ft %3D 2000 Ib 300 lb/ft 6 in, CTI 4 in. 3 ft 3 ft
Let a = 4 m, b = 1 m, PB = 30 kN, Pc = 40 kN, and PE = 15 KN. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts PB B a Pc a PE E Calculate the reaction force Ay acting on the beam. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) Final answer in kN rounded-off to 1 decimal place
The simply supported beam with following cross section is loaded with concentrated loads and uniform load as shown. Determine a) the maximum tensile and compressive bending stress if P= 150 kip and w = 10 kip/ft, and b) the allowable uniform load w if the allowable bending stress is 24 Ksi and P = 15w. 3.169 in and c 1.5 inch Draw the FBD and calculate the reaction forces and shear and bending moment diagram. Draw the stress profile. Determine the maximum bending moment and its location 0.25 in. 3 ft 3 ft -0.25 in. 3 in. 10 ft 0.25 in. 3 in. -
Calculate the reactions at the supports and obtain the shear force and bending moment diagrams for the following shaft using MD Solids software. The diameter of the shaft is 3.5433 inches and FA = 84.80 pounds-force.
For the beam below, the support reactions at QA and B have deen calculated and given as below. Continue from shear force diagram generated from last problem, generate bending moment diagram and calculate the max bending moment along the beam: KN m. Calculate your answer to 1 decimal place. |--1m- 12 kN/m 32 KN -3 m 16 kN
For the simply supported beam subjected to the loading shown, derive equations for the shear force Vand the bending moment M for any location in the beam. (Place the origin at point A.) Let a=2.75 m, b=5.00 m, PB = 60KN, and Pc = 80kN. Construct the shear- force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. Answers: Ay = Dy= tel tel a i B a Calculate the reaction forces Ay and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) PB B a PB Pc a C Pc C KN b KN D b D X D₂ X
For the simply supported beam subjected to the loading shown, derive equations for the shear force Vand the bending moment M for any location in the beam. (Place the origin at point A.) Let a=2.50 m, b=4.25 m, PB = 45kN, and Pc = 90kN. Construct the shear- force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. Answers: Ay = Dy= Mi i B Calculate the reaction forces Ay and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) PB a PB B a Pc a Pc C kN b KN b D X D₂ X
For the beam shown, the magnitude of the distributed load is wo = 11.8 kN/m and the beam length is L = 7.9 m. (a) derive equations for the shear force Vand the bending moment M for any location in the beam. Place the origin at point A. (b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determine the maximum shear force and maximum bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. Wo A В L. Answer: Vmax = kN Mmax kN•m
For the beam shown, the magnitude of the distributed load is Wo = 10.4 kN/m and the beam length is L = 4.8 m. (a) derive equations for the shear force Vand the bending moment M for any location in the beam. Place the origin at point A. (b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determine the maximum shear force and maximum bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. Wo A L Answer: Vmax = kN Mmax = kN•m Save for Later Attempts: 0 of 1 used Submit Answer