Concept explainers
A 5 m wide braced excavation is made in a saturated clay, as shown in Figure P19.1, with the following properties: c = 20 kN/m2, ϕ = 0, and γ = 18.5 kN/m3. The struts are spaced at 5 m center to center in plan.
- a. Determine the strut forces.
- b. Determine the section modulus of the sheet pile required, assuming σall = 170 MN/m2.
- c. Determine the maximum moment for the wales at levels B and C.
a.
Find the strut force.
Answer to Problem 19.1P
The strut load at A, B, C is
Explanation of Solution
Given information:
The width of excavation is 5 m.
The height of excavation cut H is 7 m.
The unit weight of saturated clay
The coefficient of internal friction
The cohesion (c) is
The center to center spacing of strut s is 5 m.
Calculation:
Check the condition for soft to medium clay as follows:
Hence, the clay is considered as soft to medium clay.
Find the maximum lateral pressure using the formula.
The maximum lateral pressure is
Step-1:
Indicate the struts are labeled as A, B, and C and its carrying load as
Draw the pressure diagram as shown in Figure.
The strut sheet pile connection at B is assumed to be hinge.
Find the strut load per meter width of excavation as follows:
At the top block,
For the bottom block,
Find the strut force at A
Find the strut load at B
Find the strut load at C
Therefore, The strut load at A, B, C is
b.
Find the required section modulus for sheet pile section.
Answer to Problem 19.1P
The section modulus is
Explanation of Solution
Given information:
The allowable pressure
Calculation:
For top block,
Consider the maximum moment occurs at distance
Find the maximum moment as follows:
The maximum moment occurs at C in the lower block
Find the maximum moment at lower block as follows:
Consider that the higher value of maximum moment is
Find the required section modulus using the formula:
Refer Table 18.1, “Properties of some commercially available sheet-pile section” in the textbook.
Take the section designation as PZ-22 according to the values.
Therefore, the section modulus is
c.
Find the maximum moment for the two wales.
Answer to Problem 19.1P
The maximum moment for the wall at B is
The maximum moment for the wall at C is
Explanation of Solution
Find the maximum moment for the wall at B,
Find the maximum moment for the wall at C,
The maximum moment for the wall at B is
The maximum moment for the wall at C is
Want to see more full solutions like this?
Chapter 19 Solutions
Principles of Foundation Engineering (MindTap Course List)
- Question 3 A new underground tunnel section is designed by a geotechnical consultant. For the underground station a 5 m wide braced excavation is made in a saturated clay as shown in Figure Q3 with unit weight, y = 18.5 kN/m², friction angle, o = 0° and cohesion, c = 20 kN/m?. The struts are spaced at 5 m center to center in plan. Refer Appendix 1 to select the sheet-pile section. i. Draw the strut forces. ii. Determine the section modulus of the sheet pile needed. Assume oall = 170 MN/m? iii. Determine the maximum moment for the wales at levels B and C. Show a complete answer, including all numerical values and necessary diagrams. 5 m 3 m B 2 marrow_forwardA 600mm diameter pile is embedded in 3 layers of dense sand at a depth of 17m. Nq = 86. The groundwater table is situated between Layers 2 and 3. The layers have the following properties: Layer 1: γ = 16.9 kN/m3. 3m thick. Layer 2: γ = 17.6 kN/m3. 5.5m thick. Layer 3: γsat = 19.65 kN/m3. K is 0.9 and tan α = 0.37. The factor of safety is 3.0. What is the allowable axial load capacity of the pile in kN? 5476.785 1750.169 1127.606 2439.011 None of the choices 2365.846 Please answer this asap. For upvote. Thank you very mucharrow_forwardGiven: γ =17.5 kN/m3c = 30 kN/m2center-to-center spacing of struts in the plan = 5 m. Determine the sheet-pile section modulus for the braced cut. Use σ all = 170 MN/m2arrow_forward
- A 11.8 m long cantilever sheet pile retaining wall is to be used to support the 6.2 m deep excavation as shown in figure. Plot the profile of horizontal effective stress in front and back of the retaining wall. Use the Rankine method. GGoound level 2.5 m Y G.W.L Grravel d'= 35°, c'-o P= 22k d'z 40° c'zo Sheet pile wg.s 6-2marrow_forwardA construction project of cantilever sheet pile penetrating saturated clay is designed to form a sheet pile wall along a riverbank as shown in Figure C. Determine: i. - ii. The theoretical and actual depth of penetration by using Dactual = 1.5D theory The maximum size of sheet pile section necessary by using all = 172.5 MN/m². Sand A y=16 kN/m³ c' = 0 2m Water table p=32 Sand Ysat 19.35 kN/m³ c' = 0 4'=32 Clay Vsat 19.35 kN/m³ c′ = 46.9 kN/m² 3m Figure C E B Riverbedarrow_forwardProblem #1 The figure below shows a cantilever sheet-pile wall penetrating a granular soil. Here, L₁ = 4 m, L₂ = 8 m, unit weight above water table= 16.1 kN/m³, saturated unit weight = 5 18.2 kN/m³, and friction angle of sand = 32 degrees. a. What is the theoretical depth of embedment, D? b. For a 30% increase in D, what should be the total length of the sheet piles? c. Determine the theoretical maximum moment of the sheet pile. d. If the allowable flexural stress = 170 MPa, compute the required section modulus of the sheet pile. Water table Dredge line Sand Y <=0 Sand Ysat c'=0 Sand Ysat c'=0arrow_forward
- Problem #1 The figure below shows a cantilever sheet-pile wall penetrating a granular soil. Here, L1 = 4 m, L2 = 8 m, unit weight above water table= 16.1 kN/m3, saturated unit weight = 5 18.2 kN/m3, and friction angle of sand = 32 degrees. a. What is the theoretical depth of embedment, D? b. For a 30% increase in D, what should be the total length of the sheet piles? c. Determine the theoretical maximum moment of the sheet pile. d. If the allowable flexural stress = 170 MPa, compute the required section modulus of the sheet pile.arrow_forwardAn excavation in soft clay is supported by a braced sheet pile wall. Calculate the force in strut A. O a. 631.92 kN O b. 151.67 kN O c. 203.53 kN O d. 430.87 kN Struts are spaced 2.5 m centre to centre Soft clay %=17kN/m³ S20 kPa $=0° max=yH = YH (1-4) H Q|25Harrow_forwardQuestion 2 Refer to the braced cut shown in Figure Q2, for which y = 17.6 kN/m², 6' = 32°, and c’ = 0. The struts are located 4 m on center-to-center in the plan. Draw the earth-pressure envelope and determine the strut loads at levels A, B, and C. Determine also: a. The sheet-pile section modulus, assume that Gan =170 x 10³ kN/m? b. The required section modulus of the wales at level A; assume that Gan = 173 x 10º kN/m² -5 m- 2 m A 3 m В c = 0 3 m C 1 marrow_forward
- Figure below shows the cross-section of an excavation which is to be made alongside a river. Write down an expression for the effective stress at level A-A and use this to establish the depth H to which the water in the trench can be reduced before instability occurs (when o'z is zero). The shear resistance at the clay and sheet pile interface can be considered negligible. sheet piling River peaty silt 3.5 m dredge level 8 m . alluvial silty clay 6.0 m (y 18 kN/m³) 3 m coarse 3.5 m gravel impervious red marlarrow_forwardProperties of soil and concrete 4m O = 30° Cohesion =0 Coefficient of base friction = 0. 50 Soil's ultimiate bearing capacity= 425 kNm deoncrete = 23.6 kN /m? Use Ronkine's theory considering no evoson and future excavation would happen in the Soil. %3D 12 D. %3D a) Determine the location of the active force from the base. b) Determine the total noirmal force reaction of soil at the boser c) Determine FS SLIDING . d) Determine FSauturning o e) Determine FSpering.arrow_forwardDetermine the depth of embedment required for stability of the cantilever sheet pile wall shown by using the factored strength method, taking F4 = 1.3. Coarse-grained soil Ysat = 20 kN/m O's = 39" 3 m 8 = O'csarrow_forward
- Principles of Foundation Engineering (MindTap Cou...Civil EngineeringISBN:9781337705028Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage LearningPrinciples of Foundation Engineering (MindTap Cou...Civil EngineeringISBN:9781305081550Author:Braja M. DasPublisher:Cengage Learning