DESCRIBE THE PROCESSES AND CYCLES?

Q: Define Cycle slips and how they are created?

A: A cycle slip is a discontinuity in a receiver's phase lock on a satellite's signal.

Q: What type of Oven is used in a Bread Manufacturing Plant?

A: Oven is an equipment where bread is baked upto required temperature in Bread manufacturing unit.

Q: Explain the temperature Changes: Heat Capacity ?

A: Temperature change- process where the temperature of body changes or hotness of body changes  i.e in…

Q: If the cylinder in Problem 6 has a stroke of 40 cm, what is the maximum cycle rate that might be…

A:

Q: 3. I just need the figure or graph of this, A 4-stroke, 4-cylinder Spark Ignition engine is running…

A:

Q: ed on the given efficiency?

A:

Q: Task 1: Your first customer asked for an internal combustion engine to use it in a designed car.…

A:

Q: Identify the most common water turbines and the limitations that exist within these different types?

A: A water turbine is a device which is used to produce the energy .these turbines are installed in…

Q: P a Pa P,/2 b 2V.

A: For solution refer below images.

Q: 3. Explain about pipeline pigging?

A: Solution:   Pigging in Pipeline is explained below:

Q: State and explain the simple change you would have to make to your FLUENT setup to see a shock in…

A: Ansys fluent is a cae software package of ansys which uses finite volume method to solve simulation…

Q: 7. Describe how one would calculate the net heat input or equivalently the net work developed by the…

A:

Q: Describe the Mass and Volume Flow Rates?

A: Mass flow rate is the mass of fluid crossing a cross-section area per unit time. If a density of the…

Q: What do you mean by scavenging process? It is positive in case of four strokes engines and negative…

A: The scavenging process is a process of exchanging fresh air-fuel mixture and exhaust gas from the…

Q: 4. How does the latent heat of water vary with the working pressure? Explain.

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: average power consumption

A: Given;    cast iron  block of ,length=200 mmdepth of cut=4 mmfeed=0.25 mm/ strokecutting edge angle,…

Q: Answer the following: A.) What is the significance of using multiple feedwater heaters? (Write your…

A: Given Data⇒ Multiple feedwater heaters Difference between using multiple feedwater heaters and using…

Q: Isothermal process is the best for production of maximum work for all working fluids. False True

A: As we know there are various thermodynamic processes such as isobaric process, isochoric process,…

Q: 5W 4W 8W 8W 2a 2a

A: given simply supported beam as shown below

Q: Air is used as a working substance in a given internal combustion engine, which is supplied with…

A:

Q: State any 15 Advantages of FBC Boiler also give one line explanation of every advantage you state.

A: Introduction: In India, the majority of the coal that is accessible is of poor quality, has a high…

Q: 1-why the heat exchanger are produce from stainless-steel? 2-what are the differentiation between…

A: Answer 1: The primary function of the heat exchangers is exchange the heat from hotter fluid to the…

Q: Explain the following types of processes with one example of each - isothermal, isobaric,…

A: An isothermal process is a thermodynamic process during which temperature of system remains…

Q: Superheating is beneficial as it

A: As per the guidelines of company we are subjected to solve only one question at a time. please…

Q: Describe Isentropic Processes of Ideal Gases

A:

Q: DEFINE THE SYSTEMS AND CONTROL VOLUMES?

A: A thermodynamics system is isolating a certain region of space which is of your interest and you…

Q: steam consumption ?

A: Given; For an ideal rankine cycle operating between pressures of, P1=30 bar P2=0.04 barThe work…

Q: Select the by-products of the blast furnace process

A: A blast furnace is a process to produce liquid metals by iron ore in a big furnace. In this process,…

Q: 2. Find the theoretical C.O.P. for a CO2 machine working between the temperature range of 25°C and –…

A:

Q: efficiency and pres Explain each of the processes on the T-s diagram.

A: Given: Gas turbine cycle Describe the processes.

Q: hat does back work ratio mean and should it be greater than one?

A: In  turbine  air expend and produced work. The part of the the work is being utilized to run the…

Q: room is heated by an iron that is left plugged in. Is this a heat or work injection? Take the entire…

A: It is required to evaluate given statement

Q: COP for the HP?

A: Given; An industrial heat pump operates between the temperature of; T1=270 C=27+273T1=300 KT2=-130C…

Q: Calculate: (i) Boiler efficiency. (ii) Percentage of heat loss in flue gas. (iii) Percentage of heat…

A: all the given data in ques to be used heat generated by the burning of coal per hour; Ha Ha=…

Q: Why balancing of the rotating masses is necessary for machines with any two oil and gas plant…

A: Balancing of rotating masses

Q: The rotational angle during flame propagation is from 12° 6TDC to 12° aTDC, for an engine running at…

A:

Q: What is organic Rankine cycle? Describe and classify the fluids used through the T-s diagram.

A:

Q: f an engine has a bore of 0.1 m, stroke of 0.08 m, inlet flow effective area of 4.0 × 10−4 m2, and…

A: To obtain the maximum volumetric efficiency it has to satisfy the below expression.

Q: To mention some types of engine lathes such as : Standard engine,Manufacturing engine,Bench lathers…

A: Option c is correct

Q: Calculate isothermal efficiency, power required to

A: To find  isothermal efficiency Power required

Q: Give another one example problem with solution of actual reheat

A:

Q: 6- Write the composition of thermocouple?

A: Given data  What is the composition of thermocouple.

Q: Explain two technical points for direct and indirect fired heaters

A: Direct heater: A direct heater or direct fire heater is a type of heater in which a burner  transfer…

Q: maximum possible reduction

A: Given: A thick slab is being cold rolled using roll of: Diameter(d)=600mm R=300 mm Coefficient of…

Q: a. Draw the system b. Draw process flow diagram for the cycle c. Draw detail Ts diagram for this…

A: Given that ,  Larger freezer temperature = -0°C Outside temperature = 25°C

Q: How to extract geothermal energy ?

A: Geothermal energy is natural heat energy that is obtained by the earth. This is an eco-friendly and…

Basic Thermodynamic Processes

The word 'thermodynamics' can be divided into two words, 'thermo' and 'dynamics'. The word thermo deals with the heat and thermal phenomenon, whereas dynamics deals with forces or external agent that drives the heat flow or aids in the motion of heat.