A man attaches a divider to an outdoor faucet so that water flows through a single pipe of radius 9.65 mm into four pipes, each with a radius of 5.80 mm. If water flows through the single pipe at 1.35 m/s, calculate the speed (in m/s) of the water in the narrower pipes. ?m/s

A man attaches a divider to an outdoor faucet so that water flows through a single pipe of radius 9.65 mm into four pipes, each with a radius of 5.80 mm. If water flows through the single pipe at 1.35 m/s, calculate the speed (in m/s) of the water in the narrower pipes. ?m/s

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter15: Fluids

Section: Chapter Questions

Problem 54PQ: Liquid toxic waste with a density of 1752 kg/m3 is flowing through a section of pipe with a radius...

See similar textbooks

Related questions

Q: A cube of wood having an edge dimension of 20.7 cm and a density of 655 kg/m³ floats on water. (a)…

A: Given:Edge dimension of cube, a = 20.7 cmdensity of cube of wood, ρ0 = 655 kg/m3

Q: 79) A pressurized cylindrical tank, 5.0 m´in diameter, contains water that emerges from the pipe at…

A: Given : d = 5 m vC = 84 m/s AB = 0.08 m2 AC = 0.07 m2

Q: A solid cylinder with base area A= 20 cm^2 is placed completely underwater as shown in the figure.…

Q: The venturi meter is a device used to measure the speed of a fluid in a pipe.the cross sectional…

Q: Water flowing through a garden hose of diameter 2.78 cm fills a 21.0 L bucket in 1.60 min. (a) What…

A: Use the concepts of water flow through a hose pipe.

Q: The Venturi tube shown in the figure below may be used as a fluid flowmeter. Suppose the device is…

A: Given Information:- Density of gasoline is ρ=7.00×102 kg/m3 Radius of the inlet pipe is…

Q: A horizontal pipe narrows from a radius of 0.220 m to 0.110 m. If the speed of the water is 1.50 m/s…

A: Given data: Radius of Larger pipe (r1) = 0.220 m Radius of smaller pipe (r2) = 0.110 m Speed of…

Q: Water flowing through a garden hose of diameter 2.79 cm fills a 25.0 L bucket in 1.10 min. (a) What…

A: Given data: Diameter, d = 2.79cm Time, T = 1.10min Velocity, v = 25L

Q: Water is flowing in a cylindrical pipe of varying circular cross-sectional area, and at all points…

A: Given data: Radius at one point (r) = 0.135 m Volume flow rate (Q) = 1.45 m3/s Speed of water at…

Q: A cylindrical container of water has a 12.0-cm diameter and the water level is 62.0cm from the…

Q: Water is flowing in a pipe with a circular cross section but with varying cross-sectional area, and…

A: (a) Given: The radius of the pipe at the first point is 0.150 m. The flow rate is 1.20 m3/s.

Q: The volume flow rate in a small rubber water pipe is 7.99 x10−6 m3/s. If the radius of the pipe is…

Q: Water flowing through a garden hose of diameter 2.72 cm fills a 22.0-L bucket in 1.45 min. (a) What…

Q: The Venturi tube shown in the figure below may be used as a fluid flowmeter. Suppose the device is…

Q: A large storage tank, open to the atmosphere at the top and filled with water, develops a small hole…

Q: Water flowing through a garden hose of diameter 2.76 cm fills a 25.0 L bucket in 1.20 min. (a) What…

Q: Water flowing through a garden hose of diameter 2.76 cm fills a 23.0-L bucket in 1.20 min. (a) What…

A: (a) The volume rate is given by, Vt=AvVt=πd22v The formula for speed of water at the end of the hose…

Q: A jet of water squirts out horizontally from a hole near the bottom of the tank shown in the figure.…

Q: The Venturi tube as shown in the figure may be used as a fluid flowmeter. Suppose the device is used…

Q: Q1: A water pipe narrows from a radius of (R1=5 cm) to a radius of (R2=2 cm. If the speed of the…

A: Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Water flows in the horizontal pipe shown in the figure. At A the diameter is 5.00 cm and at B the…

A: Diameter of the section A is d1 = 5 cm = 0.05 m Diameter of section B is d2 = 4 cm = 0.04 m Density…

Q: Water flowing through a garden hose of diameter 2.78 cm fills a 21.0 L bucket in 1.60 min. (a) What…

Q: ....…...... A cylindrical bucket sitting on the edge of a table has a 3.20 mm diameter hole near the…

A: Solution:-

Q: A square metal sheet 2.9 cm on a side and of negligible thickness is attached to a balance and…

Q: Hot water with a density of 980 kg/m3 flows through a 53 mm diameter round pipe at 1.71 m/s. What…

Q: Water flowing through a garden hose of diameter 2.72 cm fills a 23.0-L bucket in 1.45 min. (a) What…

A: Given: The diameter of hose is d=2.72 cm. The volume of bucket is V=23 L. The time of filling is…

Q: Water flows through a water hose at a rate of Q1 = 580 cm3/s, the diameter of the hose is d1 = 1.99…

A: Given , flow rate ,Q1 = 580 cm3/sdiameter , d1 = 1.99 cmvelocity , v2 = 11.2 m/s Area = πD22 =πD24…

Q: A large storage tank, open at the top and filled with water, develops a small hole in its side at a…

A: Recall v=2gh And volume rate flow=Av

Q: A horizontal pipe widens from a radius of 0.150 m to 0.280 m. If the speed of the water is 1.40 m/s…

Q: A simple U-shaped tube that has both ends open is partially filled with water. Under these…

Q: A large storage tank, open to the atmosphere at the top and filled with water, develops a small hole…

Q: A horizontal pipe widens from a radius of 0.110 m to 0.240 m. If the speed of the water is 1.30 m/s…

A: Write the equation of continuity of fluids.

Q: A cylindrical bucket sitting on the edge of a table has a 3.50 mm diameter hole near the bottom.…

Q: A plate in the shape of an isosceles triangle with base 1 m and height 20 m is submerged vertically…

Q: A cylindrical container of water has a 13.0-cm diameter and the water level is 50.0cm from the…

A: Write the given data. d=13 cmh=50 cm=0.50 m

Q: A jet of water squirts out horizontally from a hole near the bottom of the tank shown in the figure.…

A: Let depth of water inside the tank be h

Q: Hot water with a density of 980 kg/m3 flows through a 53.5 mm diameter round pipe at 1.04 m/s. What…

A: Given data: Density of water (ρ) = 980 kg/m3 Diameter (d) = 53.5 mm = 53.5×10-3 m Speed (v) = 1.04…

Q: A cylinder, filled with water, contains a small hole through the side of the cylinder, 45 cm below…

A: According to the law of conservation of energy , energy can neither be created nor destroyed but…

Q: Two hoses are connected to the same outlet using a Y-connector, as the drawing shows. The hoses A…

Q: Water flows through a water hose at a rate of Q1 = 520 cm3/s, the diameter of the hose is d1 = 2.13…

Q: Assignment Q1: A water line with an internal radius of 6.5 × 10-3 m is connected to a shower head…

A: "As per the guidelines i solved the first question alone". 1) (a) Find the volume flow rate of the…

Q: A square metal sheet 2.8 cm on a side and of negligible thickness is attached to a balance and…

Q: A U-tube open at both ends is partially filled with water (Figure a). Oil having a density of 790…

A: Part a Determine the difference h in the heights of the two liquid surfaces.part bthe speed(v) of…

Q: Q1: A water pipe narrows from a radius of (R1=5 cm) to a radius of (R2=2 cm. If the speed of the…

A: Answer 12.5 m/s

Q: What is the flow rate of water (in m3/s) hose that can fill 1.75 L bottle in 5 seconds? Group of…

A: Given, Volume of water = 1.75 L = 1.75×10-3 m3 Time = 5s Flow rate = Volume filledTime taken

Q: Water flows through a water hose at a rate of Q1 = 640 cm3/s, the diameter of the hose is d1 = 2.2…

Question

?m/s

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

The flow rate of blood through 2.00106 -m-radius capillary is 3.80109 cm3/s. (a) What is the speed of the blood flow? (This small speed allows time for diffusion of materials to and from the blood.) (b) Assuming all the blood in the body passes through capillaries, how many of them must there be to carry a total flow of 90.0 cm3/s? (The large number obtained is an overestimate, but it is still reasonable.)
Figure P15.52 shows a Venturi meter, which may be used to measure the speed of a fluid. It consists of a Venturi tube through which the fluid moves and a manometer used to measure the pressure difference between regions 1 and 2. The fluid of density tube moves from left to right in the Venturi tube. Its speed in region 1 is v1, and its speed in region 2 is v2. The necks cross-sectional area is A2, and the cross-sectional area of the rest of the tube is A1. The manometer contains a fluid of density mano. a. Do you expect the fluid to be higher on the left side or the right side of the manometer? b. The speed v2 of the fluid in the neck comes from measuring the difference between the heights (yR yL) of the fluid on the two sides of manometer. Derive an expression for v2 in terms of (yR yL), A1, A2, tube, and mano. FIGURE P15.52
Figure 11.35(a) shows the effect of tube radius on the height to which capillary action can raise a fluid. (a) Calculate the height h for water in a glass tube with a radius of 0.900 cm—a rather large tube like the one on the left. (b) What is the radius of the glass tube on the right if it raises water to 4.00 cm?
Calculate the Reynolds numbers for the flow of water through (a) a nozzle with a radius of 0.250 cm and (b) a garden hose with a radius of 0.900 cm, when the nozzle is attached to the hose. The flow rate through hose and nozzle is 0.500 us. Can the flow in either possibly be laminar?
Liquid toxic waste with a density of 1752 kg/m3 is flowing through a section of pipe with a radius of 0.312 m at a velocity of 1.64 m/s. a. What is the velocity of the waste after it goes through a constriction and enters a second section of pipe with a radius of 0.222 m? b. If the waste is under a pressure of 850,000 Pa in the first section of pipe, what is the pressure in the second (constricted) section of pipe?
Water emerges straight down from a faucet with a 1.80-cm diameter at a speed of 0.500 m/s. (Because of the construction of the faucet, there is no variation in speed across the stream.) (a) What is the flow rate in cm3/s? (b) What is the diameter of the stream 0.200 m below the faucet? Neglect any effects due to surface tension.
Figure P15.47 shows a stream of water in steady flow from a kitchen faucet. At the faucet, the diameter of the stream is 0.960 cm. The stream fills a 125-cm3 container in 16.3 s. Find the diameter of the stream 13.0 cm below the opening of the faucet. Figure P15.47
(a) A water hose 2.00 cm in diameter is used to fill a 20.0-L bucket. If it takes 1.00 min to fill the bucket, what is the speed v at which water moves through the hose? (Note: 1 L = 1 000 cm3.) (b) The hose has a nozzle 1.00 cm in diameter. Find the speed of the water at the nozzle.
(a) Verify that a 19.0% decrease in laminar flow through a tube is caused by a 5.00% decrease in radius, assuming that all other factors remain constant, as stated in the text. (b) What increase in flow is obtained from a 5.00% increase in radius, again assuming all other factors remain constant?
(a) What is the fluid speed in a fire hose with a 9.00-cm diameter carrying 80.0 L of water per second? (b) What is the flow rate in cubic meters per second? (c) Would your answers be different if salt water replaced the fresh water in the fire hose?
(a) Estimate the time it would take to fill a private swimming pool with a capacity of 80,000 L using a garden hose delivering 60 L/min. (b) How long would it take to fill if you could divert a moderate size river, flowing at 5000 m3/s, into it?
Archimedes' principle can be used to calculate the density of a fluid as well as that of a solid. Suppose a chunk of iron with a mass of 390.0 g in air is found to have an apparent mass of 350.5 g when completely submerged in an unknown liquid. (a) What mass of fluid does the iron displace? (b) What is the volume of iron, using its density as given in Table 11.1 (c) Calculate the fluid's density and identify it.