Principles of Foundation Engineering (MindTap Course List)
9th Edition
ISBN: 9781337705028
Author: Braja M. Das, Nagaratnam Sivakugan
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 2, Problem 2.20P
To determine
Find the pore water pressure within the specimen.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A consolidated undrained triaxial test was
performed on a normally consolidated clay
with a critical state friction angle of 230. After
an initial isotropic consolidation at a cell
pressure of 50 kPa, drainage was turned off,
the cell pressure was increased to 85 kPa,
and the sample was loaded to ultimate
conditions. A pore pressure of 55 kPa was
measured at ultimate state. What value of
major principal total stress was measured at
the ultimate state?
A consolidated drained (CD) triaxial test was carried out on a normally consolidated clay. The specimen was consolidated under a cell pressure of 100 kPa and back pressure of 30 kPa. The axial deviatoric stress was increased very slowly to failure, so that there was no excess pore water pressure developed during the shearing. The specimen failed under a deviatoric stress of 130 kPa. The back pressure of 30 kPa was maintained throughout the test.
(i) What is the friction angle in terms of effective stresses? (ii) What are the shear stress and normal stress acting on the failure plane?
Solution fast please
A consolidated drained (CD) triaxial test was carried out on a normally consolidated clay. The specimen was consolidated under a cell pressure of 100 kPa and back pressure of 30 kPa. The axial deviatoric stress was increased very slowly to failure, so that there was no excess pore water pressure developed during the shearing. The specimen failed under a deviatoric stress of 130 kPa. The back pressure of 30 kPa was maintained throughout the test.
(1) What is the friction angle in terms of effective stresses?
(ii) What are the shear stress and normal stress acting on the failure plane?
Chapter 2 Solutions
Principles of Foundation Engineering (MindTap Course List)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- A drained triaxial compression test on a saturated clay yielded the effective shear strength parameters as c' = 15 kPa and o'= 22°. %3D Consolidated Undrained triaxial test on an identical sample of this clay at a cell pressure of 200 kPa developed a pore water pressure of 150 kPa at failure. The deviator stress (expressed in kPa) at failure isarrow_forwardThe shear strength parameters in terms of effective stress are: C = 15 kPa and o' = 30°. In an unconsolidated undrained (UU) triaxial test on a sample of this clay, the cell pressure was 250 kPa and the deviator stress at failure was 136 kPa. The pore water pressure at failure will be (in kN/m2, upto one decimal place).arrow_forwardIn a triaxial test, a specimen of saturated [normally consolidated] clay was consolidated under a chamber confining pressure of 80 kPa. The axial stress on the specimen was then increased through the allowing the drainage from the specimen. The specimen fails when 120 kPa. The pore water pressure at the time was 50 kPa. What is the consolidated undrained friction angle [phi]?arrow_forward
- 5. A consolidated, undrained triaxial test is being caried out on a normally consolidated clay where c = 0 and 41= 26'. The triaxial specimen was consolidated under a cell pressure of 300 kPa and backpressure of 80 kPa. Skempton's A parameter at failure is estimated to be 0.80. The drainage valve has since been dosed and the vertical deviator stress increased to failure. What would be the deviator stress and pore water pressure at failure?arrow_forwardA consolidated-undrained triaxial test was conducted on a dense sand with a chamber-confining pressure of 20 lb/in?. Results showed that o' = 24° and o = 31°. Determine the deviator stress and the pore water pressure at failure.arrow_forward5. A consolidated, undrained triaxial test is being carried out on a normally consolidated clay where c - 0 and p'= 26'. The triaxial specimen was consolidated under a cell pressure of 300 kPa and backpressure of 80 kPa. Skempton's A parameter at failure is estimated to be 0.80. The drainage valve has since been dosed and the vertical deviator stress increased to failure. What would be the deviator stress and pore water pressure at failure?arrow_forward
- The results below were obtained at failure in a series of consolidated-untrained triaxial tests, with pore water pressure measurement, on specimens of a fully saturated clay. Determine the values of the shear strength parameters c' and 'If a specimen of the same soil were consolidated under an all-round pressure of 300 kN/m² and the principal stress difference applied with the all-round pressure changed to 400kN/m², what would be the expected value of principal stress difference at failure" 150 300 450 600 03 (kN/m²) 01-03 (kN/m²) u (kN/m²) 103 202 305 410 82 169 252 331arrow_forward• In consolidated-drained triaxial test on a normally consolidated clay, the specimen failed at a deviator stress of 124 KN/sq.m. If the effective stress friction angle is known to be 31°, what was the effective confining pressure at failure?arrow_forwardA consolidated-drained triaxial test is carried out on a sand specimen that is subjected to 80 kN/m² confining pressure. The vertical deviator stress was increased slowly such that there is no built-up of pore water pressure within the specimen. The specimen failed when the addition axial stress reached 240 kN/m². Find the friction angle of the sand. If another identical sand specimen was subjected to 150 kN/m' confining pressure, what would be the deviator stress at failure.arrow_forward
- Q3: Undisturbed samples from a normally consolidated clay layer were collected during a field exploration program. Drained triaxial tests showed that the effective friction angle Ø'=28°. The unconfined compressive strength, qu, of a similar specimen was found to be 148 kN/m2. Determine the pore pressure at failure for the unconfined compression test.arrow_forwardA consolidated-undrained triaxial test was conducted on a saturated, normally consolidated clay. The test results are 03-13 lb/in2 01(failure) = 32 lb/in² Pore pressure at failure = u = 5.5 lb/in². Determine c, d, c', and 'arrow_forwardA triaxial shear test was performed on a well-drained sand sample. The normal stress on the failure plane and the shear stress on the failure plane, at failure were determined to be 6100 psf and 4600 psf, respectively. a. Determine the angle of internal friction of the sand? b. Determine the angle of the failure plane? c. Determine the maximum principal stress? Please answer this asap. For upvote. Thank you very mucharrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Principles of Foundation Engineering (MindTap Cou...Civil EngineeringISBN:9781337705028Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage LearningPrinciples of Geotechnical Engineering (MindTap C...Civil EngineeringISBN:9781305970939Author:Braja M. Das, Khaled SobhanPublisher:Cengage LearningFundamentals of Geotechnical Engineering (MindTap...Civil EngineeringISBN:9781305635180Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage Learning
Principles of Foundation Engineering (MindTap Cou...
Civil Engineering
ISBN:9781337705028
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning
Principles of Geotechnical Engineering (MindTap C...
Civil Engineering
ISBN:9781305970939
Author:Braja M. Das, Khaled Sobhan
Publisher:Cengage Learning
Fundamentals of Geotechnical Engineering (MindTap...
Civil Engineering
ISBN:9781305635180
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning