In this lab, concentrated HCl was added to 2-methyl-2-butanol in a separatory funnel. The reactants were shaken to help the reaction occur quickly. The separatory funnel was vented several times, to reduce pressure that resulted from the reaction which was due to the high vapor pressure of HCl. The Hydrochloric acid will dissociate, and the H+ will react with the OH-C to form H2O-C. The H2O is a good leaving group. As the LG is on a tertiary carbon, an Sn1 reaction should occur. In the rate determining step, the water will leave, to produce a tertiary carbocation. In the second (fast) step, the Cl- nucleophile from the dissociated HCl will attack the carbocation and 2-chloro-2-mehtylbutane forms. In this reaction, some E1 also occurs; however, HCl will react with the product of E1 to produce the 2-chloro-2-methylbutane product. In the lab, after the reaction occurred, the product needed to be purified as excess HCl was used and still remained. To purify the product, a series of reactions were completed. …show more content…
The percent recovery was calculated by finding the moles of the initial and final products. The moles of the initial product were found by multiplying the volume used by the density of 2-methyl-2-butanol, and then dividing by the molar mass. The percent recovery was good, showing few errors were made and that the lab went as expected. To improve the recovery, the extractions could be done even more carefully. To analyze the purity of the product, an IR test was run. 2-methyl-2-butanol has a large OH peak; 2-chloro-2-butane does not, but otherwise looks quite similar. The main peak on 2-chloro-2-butane is a C-Cl peak; however, this peak is not revealed with this IR machine, so it could not be analyzed. The IR chart for the experimental product did not have the OH peak and looked like the theoretical IR chart, meaning it was dry and that the desired product had been
Theory: One of the methods of preparing alkyl halides is via the nucleophilic substitution reactions of alcohols. Alcohols are inexpensive materials and easy to maintain. However, they are a poor leaving group the OH group is a problem in nucleophilic substitution, this problem is fixed by converting the alcohol into H2O.
During the halogenation reactions of 1-butanol, 2-butanol, and 2-methyl-2-propanol, there is a formation of water from the OH atom of the alcohol, and the H atom from the HCl solution. The OH bond of the alcohol is then substituted with the Cl atom. Therefore all of the degrees of alcohol undergo halogenation reactions, and form alkyl halides as products. This is because the functional group of alkyl halides is a carbon-halogen bond. A common halogen is chlorine, as used in this experiment.
Experiment 55 consists of devising a separation and purification scheme for a three component mixture. The overall objective is to isolate in pure form two of the three compounds. This was done using extraction, solubility, crystallization and vacuum filtration. The experiment was carried out two times, both of which were successful.
14 mL of 9 M H2SO4 was added to the separatory funnel and the mixture was shaken. The layers were given a small amount of time to separate. The remaining n-butyl alcohol was extracted by the H2SO4 solution therefore, there was only one organic top layer. The lower aqueous layer was drained and discarded. 14 mL of H2O was added to the separatory funnel. A stopper was placed on the separatory funnel and it was shaken while being vented occasionally. The layers separated and the lower layer which contained the n-butyl bromide was drained into a smaller beaker. The aqueous layer was then discarded after ensuring that the correct layer had been saved by completing the "water drop test" (adding a drop of water to the drained liquid and if the water dissolves, it confirms that it is an aqueous layer). The alkyl halide was then returned to the separatory funnel. 14 mL of saturated aqeous sodium bicarbonate was added a little at a time while the separatory funnel was being swirled. A stopper was placed on the funnel and it was shaken for 1 minute while being vented frequently to relieve any pressure that was being produced. The lower alkyl halide layer was drained into a dry Erlenmeyer flask and 1.0 g of anhydrous calcium chloride was added to dry the solution. A stopper was placed on the Erlenmeyer flask and the contents were swirled until the liquid was clear. For the distillation
The sodium hydroxide acts to pull the hydrogen off the oxygen in the 2-methylphenol so that the oxygen has a negative charge and can attack the sodium chloroacetate. Again, using a 1:1 molar ratio, 0.34 g (2.9 mmol) of sodium chloroacetate (the good leaving group) was added to 1 ml of water and dissolved. Following dissolving all of the 2-methylphenol (to avoid the sodium hydroxide reacting concurrently with the sodium chloroacetate and 2-methylphenol) in the sodium hydroxide, the aqueous solution of sodium chloroacetate was transferred to the reaction flask. This mixture was then heated to reflux, using a medicine dropper affixed to the top of the flask as an alternative method to boil without
As detailed in Pavia 's Organic Laboratory techniques the reaction is expected to proceed via the following reaction:
To begin, in order for the compounds to react they will be dissolved in water and sulfuric acid will be added. The addition of sulfuric acid will then generate hydrobromic acid, an important product in the reaction mixture. The hydrobromic acid will react with the 1-butanol when heat is added to the flask during refluxing. Refluxing is the heating of a flask to boiling and then allowing
The reaction is carried out in saturated aqueous ammonium chloride solution. Thus no special drying of solvents, reagents, or glassware is required. The reaction mechanism for this experiment can be seen below (Fig. 2)
The products of interest within this experiment are 2-methyl-1-butene and 2-methyl-2-butene from sulfuric acid and phosphoric acid catalyzed dehydration of 2-methyl-2-butanol. The reaction mixture was then separated into its separate alkene components by steam distillation and then analyzed by gas chromatography (GC), Infrared Radiation (IR) spectroscopy, and Nuclear Magnetic Resonance (NMR) imaging. Gas chromatography is an analytical technique that is able to characterize if specific compounds exist in a reaction mixture, even if they are in low quantities, assess how much of a compound exists within a reaction mixture relative to other components within the sample, and determine the purity of an isolated product. In the case of this experiment, gas chromatography is used to analyze how pure the alkene reaction sample was and if any remnants of impurities or 2-methyl-2-butanol remained in the sample after isolation of alkene components.
ssion In this experiment, 2-ethyl-1,3-hexanediol was reacted with sodium hypochlorite in an attempt to identify how sodium hypochlorite acts as a reagent. Due to the nature of 2-ethyl-1,3-hexanediol we are able to determine if sodium hypochlorite is a selective reagent. 2-ethyl-1,3-hexanediol has 2 alcohol functional groups with one being primary and the other being secondary. A selective reagent is one which oxidizes one functional group although its in the presence of 2 or more.
The reaction took place in a conical vial and .2mL of each of the reactant samples were added to it along with some 95% ethanol. Two drops of NaOH were added shortly after and stirred at room temperature for fifteen minutes. The vial was cooled in and ice bath and crystallized. Vacuum filtration was performed to filter the crude product. The crude product was recrystallized using methanol and filtered again. We made one change to the procedure and instead of using .7mL of ethanol we
Before the start of the experiment, the theoretical yield was to be calculated. First, the limiting reagent was determined from the reagents by comparing the amount of moles. Among the three reagents involved in this experiment - camphor, sodium borohydride, and methanol, camphor was found to be the limiting reagent. The moles of camphor was less than the combined moles of the other two reagents. The theoretical yield, which is the amount of product that could be possibly produced after the completion of a reaction (“Calculating Theoretical and Percent Yield”), was found to be 0.25 g. Once the product was achieved, a percent yield of 97% was determined. As a result, the reduction of camphor to isoborneol was successful.
The purpose of this lab is to understand the process of eliminating an alkyl halide to form an alkene. The experiment is carried out by first converting the alcohol, 2-methy-2-butanol, into the alkyl halide of 2-chloro-2-methylbutane that will then be put through dehydrohalogenation that favors elimination reaction (E2) to create a mixture of 2-methyl-2-butene and 2-methyl-1-butene. A fractional distillation will be taken to purify the mixture and an additional gas chromatography will be done to further analyze the mixture composition. A bromide test will be done to determine the product of an alkene in the experiment.
Part 2 to determine the empirical formula and percentage yield of the compound synthesized in Part 1. Spectrophotometry is a routine laboratory test that has the added advantage
Equipment, Materials, and Method The equipment used were a jacketed batch reactor beaker, cooling water circulation system, computer, LabPro temperature probe and conductivity probe, mixing stand and magnetic stir bar. The materials used for this reaction were a 0.08M NaOH solution and a 0.1M ethyl acetate solution. A 20% excess Ethyl acetate was used to ensure NaOH was the limiting reactant.[1] NaOH was chosen for the limiting reactant because of its high conductivity relative to Ethyl acetate. The extent of the reaction was monitored by measuring the conductivity throughout the reaction. With NaOH being the limiting reactant, the change in conductivity is more visible, and the termination of the reaction can