2. A reinforced concrete column 300 mm in diameter supports an axial compressive force of 500 kN. Determine the required area of reinforcing steel that will satisfy the following conditions: allowable stress for steel is 120 MPa whereas for concrete, the stress is limited to 6 MPa. Use E. - 200 GPa and Econ = 14 GPa.

2. A reinforced concrete column 300 mm in diameter supports an axial compressive force of 500 kN. Determine the required area of reinforcing steel that will satisfy the following conditions: allowable stress for steel is 120 MPa whereas for concrete, the stress is limited to 6 MPa. Use E. - 200 GPa and Econ = 14 GPa.

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter12: Composite Materials

Section: Chapter Questions

Problem 12.7P: Estimate the transverse tensile strength of the concrete in Problem 12.6.

See similar textbooks

Similar questions

Determine the tensile steel ratio of a singly reinforced concrete beam for the following conditions using concrete strength f’c = 28 MPa and steel yield strength fy = 420 MPa. if the tensile strain is εs = fy/Es upon crushing of concrete at a strain of 0.003. = ___ (5 decimal places)
The properties of the reinforced concrete beam are b = 315 mm, d = 460 mm, Ast = 1102 mm2, and Est / Eco = 9. If the working stresses are 16.9 MPa for concrete and 117.2 MPa for steel, determine the corresponding bending moment (in Nm) for the steel. Round off the final answer to two decimal places.
A rectangular reinforced concrete beam has a width of 350 mm and an effective depth of 650 mm. The beam is reinforced with 8-28 mm diameter tension bars. Concrete strength is f'c = 20.70 MPa and steel yield strength is fy = 275 MPa. 1. Which of the following most nearly gives the steel ratio? A. 3.73% B. 2.79% C. 2.17% D. 1.62% the rectangular
The following data of a pre-stress concrete are given: Beam dimension ; bxh = 300 mm x 600 mm Loads Super imposed dead load 7 KN/m Live load = 20 KN/m Unit Weight of concrete 23 KN/cubic meter The beam is simply supported on a span of 15 meters and are pre tensioned with total initialpre tensioned with total initial force of 1750 KN from low-relaxation strand with centroid 220 mm below neutral axis throughout the beam length .There is a 15% loss of stress at service loads. The concrete covering of the pre-stressed concrete is _____mm., the total dead load is _____ KN/m.
SIT. B: Determine the tensile steel ratio of a given conditions if concrete strength f'. = 28 MPa and steel yield strength fy 4. if the tensile strain is Es = fy/Es upon crushing of concrete at a strain of 0.003. C. 0.02833 A. 0.01567 B. 0.02161 D. 0.02125 if the tensile strain is limited to 0.004 upon crushing of concrete at a strain of 0.003. A. 0.01567 B. 0.01548 5. 6. Minimum as required by NSCP 2015. C. 0.00313 D. 0.00405 A. 0.00333 B. 0.00276 = 420 MPa. C. 0.02778 D. 0.02064 uniformly
Determine the prestressing steel area required for the precast concrete T-beam. Use the following data: Total moment = 250 kN-m Effective stress fse= 862 MPa Allowable concrete stress = f.=11 MPa Consider zero stress at the bottom of the beam I=3673x106 mm4 A=103125 mm² Eccentricity = 271.6 mm Centroid of steel is located at 100 mm from the bottom of the beam. Select one: a. 591.97 mm b. 789.29 mm 2. C. 443.98 mm 2. d. 986.61 mm
A pre stressed concrete beam has a width of 200 mm and an overall depth of 400 mm. The permissible stresses in tension and compression due to pre- stressing alone are 4 N/mm and 25 N/mm respectively. Find the required pre- stressing force in the tendon and the eccentricity of the tendon, if a straight tendon with a constant eccentricity is to be provided in the beam. No external load or self weight effect is to be considered.
A rigid steel plate is supported by three posts of high-strength concrete each having an effective cross-sectional area A = 40,000 mm2 and length L = 2 m (see figure). Before the load P is applied, the middle post is shorter than the others by an amount s = 1.0 mm. The allowable compressive stress in the concrete is 20 MPa and E of concrete is 30 GPa. What is the minimum load P (kN) needed to close the gap? P S
The cross section of a beam is shown in the figure is reinforced with 5-28 mm diameter bars placed at 100 mm from the bottom fiber. The beam is expected to carry a service moment of 280 kN-m. Use f'c=28 MPA and fy=280 MPa. All dimensions are in millimeters. Using WSD method, calculate the following: 1. Cracking moment of the section. 2 Compressive stress on the concrete., 3. Tensile stress on the steel. 4. Compressive force on the concrete. 300 I00 300 300 300 100 mm 100 -1700 mm
A rectangular reinforced concrete beam with width of 250 mm and effective depth of 500 mm is subjected to 150 kN-m bending moment. The beam is reinforced with 4-25 mm o bars. Use alternate design method and modular ratio n = 9. 1. What is the maximum stress of concrete? 2. What is the maximum stress of steel? 3. What is the total compressive force in concrete? b = 250 009=P -0000- b = 250 d-x nA. 4-25 mm Ø ΝΑ
3 Given a concrete beam (width b= 10 in., depth h = 25 in.) with flexural reinforcement at the bottom, the transformed moment of inertia is In=14,740 in“, and the location of the neutral axis from top of the beam is y = 13.2 in, assuming all material is elastic, calculate the maximum tensile stress of the concrete when a positive bending moment M= 40 kip-ft is applied to the beam. Is the section cracked under the given moment if concrete is normal weight and the compressive strength fe' is 3000 psi?
The properties of the reinforced concrete beam are b = 300 mm, d = 480 mm, Ast = 1306 mm2, and Est / Eco = 10. If the working stresses are 16.7 MPa for concrete and 104.8 MPa for steel, determine the corresponding bending moment (in Nm) for the concrete. Round off the final answer to two decimal places.