A composite shaft consists of a hollow bronze (G=40 GPa) cylinder with a 150-mm outside diameter and 100 mm inside diameter over a 50-mm diameter solid steel (G=80 GPa) core. The two members are rigidly connected to a bar at the right end and to the wall at the left end as shown below. When the couple shown is applied to the shaft, determine (a) The rotation of the bar AB in rad and its sense. (b) The maximum shearing stress in each of the members. bronze steel 2m bronze B 200 KN 300 mm 200 KN

A composite shaft consists of a hollow bronze (G=40 GPa) cylinder with a 150-mm outside diameter and 100 mm inside diameter over a 50-mm diameter solid steel (G=80 GPa) core. The two members are rigidly connected to a bar at the right end and to the wall at the left end as shown below. When the couple shown is applied to the shaft, determine (a) The rotation of the bar AB in rad and its sense. (b) The maximum shearing stress in each of the members. bronze steel 2m bronze B 200 KN 300 mm 200 KN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A two pinned end bars AB (copper) and BC (aluminum) is subjected to a horizontal force P = 90KN applied at pin B %3D as shown in the figure, determine the horizontal displacement of pin B. Aluminum: L= 1.5m, A= 1000mm2, E= 70 GPa Copper: L= 2.0m, A= 850mm², E= 120 GPa Degree: 45° Alumaum L-15m A=1000 mm E-70 GPa >P=90 kN Copper L=2.0m Aa550 mm E=120 GPa
4. For the rods shown, determine (a) the compressive force after a temperature rise of 95°C, (b) the corresponding change in length of the aluminum rod. 0.5 m Aluminum A = 2.0x10-3 m2 E 70 GPa a= 23x10-6/Oc + 0.3 m Bronze A = 1.5x10-3 m2 E = 110 GPa d=18x10-6/0c .0 mm
Canny Methed Coing 100 k f Sections determine forces in FE, FC, bc
The pin-connected structure consists of a rigid beam ABCD and two supporting bars. Bar (1) is an aluminum alloy [E = 60 GPa] with a cross-sectional area of A1 = 870 mm?. Bar (2) is a bronze alloy [E = 92 GPa] with a cross-sectional area of Ay = 520 mm?. Assume L$=2.6 m, La=2.9 m, a=0.7 m, b= 1.3 m, and c= 1.1 m. All bars are unstressed before the load P is applied; however, there is a 3.9-mm clearance in the pin connection at A. If a load of P= 58 kN is applied at B, determine: (a) the normal stresses 01, 02, in both bars (1) and (2). (b) the normal strains € , E2, in bars (1) and (2). (c) determine the downward deflection vA of point A on the rigid bar.
Q # 4: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in Figure. Axial loads are applied at the positions indicated. The value of P is limited to 20 KN in bronze, 72 KN in aluminum and 28 KN in steel Find the area of each section that will not exceed a stress in steel of 280 MPa, in aluminum of 180 MPa, or in bronze of 200 MPa. CLO -2 Steel Aluminum Bronze 2P 4P 2.5 2.0 1.5
two rods attached to a rigid bar AB with negligible mass . A 101 kN load was applied at the end of this bar. The computed stresses for steel and bronze are Blank 1 mPa and Blank 2 mPa respectively.
The composite shaft, consisting of aluminum, copper, and steel sections, is subjected to the loading shown. Determine the displacement of end A with respect to end D. The cross-sectional area and modulus of elasticity for each section are shown in the figure. Neglect the size of the collars at B and C 16 kN 8 KN 9 KN 450 mm- 16 KN C 300 mm- Section AB is Aluminum with Young's modulus of 70 GPa and an area of 63 mm². Section BC is Copper with Young's modulus of 126 GPa and an area of 87 mm². Section CD is Steel with Young's modulus of 200 GPa and an area of 39 mm. The displacement of end A with respect to end Dis Note: Please enter your answer with three significant digits after the decimal point. .mm 8 KN 400 mm- 7 KN
1. See figure below and solve for the maximum value of torque the composite shaft can accommodate given a maximum shear stress of 8ksi in bronze and 12 ksi for the steel. Assume bronze has G = 6 × 103 ksi, and for steel, G = 12 × 103 ksi. %3| L C2" 3" Hollow Bronze Steel Core D = 3 in, d = 2 in D = 2 in
Q/ Find the Maximum stresses in Steel and Aluminum. Est= 210G pa and E al%3D 70 G pa ? W= 15 Kn.M 120mm 5m Al steel 60mm 140 mm
QUESTION 3 The assembly consists of three steel rods and a horizontal bar BED. The structure supports a 36 kN load P located at middle of bar BED. Each of the rod AB and CD has a cross-sectional area of 200 mm² and rod EF has a 625 mm². Modulus of elasticity for steel is 200 GPa. Determine: (a) The change in length of rod EF. (b) The stress in each rod. 500 mm 400 mm
2. Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P = 10 kN? Specify whether tension or compression. Bronze Aluminum Steel A =400 mm2 A= 600 mm2 A = 300 mm2 2P ЗР 4P P -3 m 5 m 4 m Stress in Bronze (MPa) %D Stress in Aluminum (MPa) %3D Stress in Steel (MPa)
A hollow bronze shaft of 3 in. outer diameter and 2 in. inner diameter is slipped over a solid steel shaft 2 in. in diameter and of the same length as the hollow shaft. The two shafts are then fastened rigidly together at their ends. For bronze, G = 6 × 106 psi, and for steel, G = 12 × 106 psi. What torque can be applied to the composite shaft without exceeding a shearing stress of 8000 psi in the bronze or 12 ksi in the steel?