A hollow steel shaft with an outside diameter of 80 mm and a wall thickness of 11 mm is subjected to a pure torque of T = 5,200 N-m. (a) Determine the maximum shear stress in the hollow shaft. (b) Determine the minimum diameter of a solid steel shaft for which the maximum shear stress is the same as in part (a) for the same torque T.

A hollow steel shaft with an outside diameter of 80 mm and a wall thickness of 11 mm is subjected to a pure torque of T = 5,200 N-m. (a) Determine the maximum shear stress in the hollow shaft. (b) Determine the minimum diameter of a solid steel shaft for which the maximum shear stress is the same as in part (a) for the same torque T.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.3.19P: A solid brass bar of diameter d = 1.25 in. is subjected to torques T1as shown in part a of the...

See similar textbooks

Similar questions

A solid brass bar of diameter d = 1.25 in. is subjected to torques T1as shown in part a of the figure. The allowable shear stress in the brass is 12 ksi. What is the maximum permissible value of the torques T1? If a hole of diameter 0.625 in. is drilled longitudinally through the bar, as shown in part b of the figure, what is the maximum permissible value of the torques T2? What is the percent decrease in torque and the percent decrease in weight due to the hole?
Maximum shear stress developed on the surface of a solid circular shaft under pure torsion is 240 MPa. If the shaft diameter is doubled then the maximum shear stress developed corresponding to the same torque will be (a) 120 MPa (c) 30 MPa (b) 60 MPa (d) 15 MPa
A hollow steel shaft with an outside diameter of 90 mm and a wall thickness of 10 mm is subjected to a pure torque of T-7,300 N-m. (a) Determine the maximum shear stress in the hollow shaft. (b) Determine the minimum diameter of a solid steel shaft for which the maximum shear stress is the same as in part (a) for the same torque T. Answers: (a) Tmax MPa mm (b) dmin i
A shaft with a hollow cross section is subjected to torque of magnitude T = 5.5 kN-m. If the outer diameter of the shaft is 0.1 m and its wall thickness is 10 mm, what would be the minimum diameter of a solid steel shaft needed if it would be subjected to the maximum shear stress of the hollow shaft?
A hollow steel shaft with an outside diameter of 41 mm and a wall thickness of 9 mm is subjected to a pure torque of T = 6300 N-m. The shear modulus of the steel is G = 87 GPa. Determine: (a) the maximum shear stress T in the shaft. (b) the magnitude of the angle of twist o in a 2.4-m length of shaft. Answers: (a) = i MPа. (b) p = i
A hollow circular steel shaft with an outside diameter of 2.569. and a wall thickness of 0.388 in. is subjected to a pure torque of 292 lb-ft. The shaft is 124 in. long. The shear modulus of the steel is G-12.000 ksi. Determine the magnitude of the angle of twist in the shaft. 1. T B
Maximum shear stress developed on the surface of a solid circular shaft under pure torsion is 240 MPa. If the shaft diameter is doubled then the maximum shear stress developed corresponding to the same torque will be
Calculate the maximum and minimum shear stress in a hollow circular shaft of outer diameter 20 mm and thickness 2 mm, subjected to a torque of 92.7 N-m.
A composite shaft is made by slipping a bronze tube of 3-in. outer diameteran -in. inner diameter over a solid steel shaft of the same length and 2-in.-diameter. The two components are then fastened rigidly together at their ends. What is the largest torque that can be carried by the composite shaft if the working shear stresses are 8 ksi for bronze and 12 ksi for the steel? For bronze, G = 6 x 106 psi, and for steel, G = 12 x 106 psi
A compound steel (G= 70 GPa) shaft consists of a solid 59-mm-diameter segment (1) and a solid 39-mm- diameter segment (2). The allowable shear stress of the steel is 76 MPa, and the maximum rotation angle at the free end of the compound shaft must be limited to Pcs 4.6°. Assume ₁-0.6 m and £₂-1.0 m. Determine the magnitude of the largest torque Te that may be applied at C. Express your answer in N-m rounded to three significant digits. L₁ (1) B (2) L2 Tc C X
A compound steel (G= 70 GPa) shaft consists of a solid 59-mm-diameter segment (1) and a solid 39-mm-diameter segment (2). The allowable shear stress of the steel is 76 MPa, and the maximum rotation angle at the free end of the compound shaft must be limited to cs 4.6°. Assume L₁=0.6 m and L₂=1.0 m. Determine the magnitude of the largest torque Te that may be applied at C. Express your answer in N-m rounded to three significant digits. L₁ (1) B (2) L2 Tc C
A shaft consisting of an aluminum segment and a steel segment is acted upon by two torques. The shaft is attached to the wall at point C. The diameter of the aluminum segment is 0.062 m and the diameter of the steel section is 0.034 m. The shear elastic modulus for aluminum is G = 28 GPa and the shear elastic modulus for steel is G = 83 GPa. Calculate the angle of twist at point A if the value of T = 699 N m. Multiply your final answer by 104 and submit that as your input with four significant figures after the decimal point. For example, if your final answer is 0.00005555 then input 0.5555. Aluminum 900 mm 2T B HH Steel 600 mm T A