A shaft consisting of an aluminum segment and a steel segment is acted upon by two torques. The shaft is attached to the wall at point C. The diameter of the aluminum segment is 0.062 m and the diameter of the steel section is 0.034 m. The shear elastic modulus for aluminum is G = 28 GPa and the shear elastic modulus for steel is G = 83 GPA. Calculate the angle of twist at point A if the value of T = 699 N m. Multiply your final answer by 104

A shaft consisting of an aluminum segment and a steel segment is acted upon by two torques. The shaft is attached to the wall at point C. The diameter of the aluminum segment is 0.062 m and the diameter of the steel section is 0.034 m. The shear elastic modulus for aluminum is G = 28 GPa and the shear elastic modulus for steel is G = 83 GPA. Calculate the angle of twist at point A if the value of T = 699 N m. Multiply your final answer by 104

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.2.6P: A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius...

See similar textbooks

Similar questions

Solve the preceding problem if the length L = 56 in., the inner radius r1— 1.25 in., the angle of twist is 0.5°, and the allowable shear strain is 0.0004 rad.
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?
A thin-walled aluminum tube of rectangular cross section (sec fig me) has a centerline dimensions b = 6.0 in. and b = 4.0 in. The wall thickness t is constant and equal to 0.25 in. Determine the shear stress in the tube due to a torque T = 15 kip-in. Determine the angle of twist (in degrees) if the length L of the tube is 50 in. and the shear modulus G is 4.0 x 106 psi.
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A solid circular shaft AB of diameter d is fixed against rotation at both ends (sec figure), A circular disk is attached to the shaft at the location shown. What is the largest permissible angle of rotation 0max of the disk if the allowable shear stress in the shaft is Tallow? [Assume that a >b. Also, use Eqs. (3-50a and b) of Example 3-9 to obtain the reactive torques.]
A circular pole is subjected to linearly varying distributed force with maximum intensity t0. Calculate the diameter daof the pole if the maximum allowable shear stress for the pole is 75 M Pa.
A circular steel tube with an outer diameter of 75 mm and inner diameter of 65 mm is subjected to torques 7"at its ends. Calculate the maximum permissible torque 7jliajl if the allowable normal strain is ea= 5 X 10"4 Assume that G = 15 GPa.
A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions shown in the figure. The magnitudes of the torques are T1= 1000 lb-in., T2= T4= 500 lb-in., and T3= T5= 800 lb-in. The tube has an outside diameter of d2= 1.0 in. The allowable shear stress is 12,000 psi and the allowable rate of twist is 2.0°/ft. Determine the maximum permissible inside diameter d1, of the tube.
A circular copper bar with diameter d = 3 in. is subjected to torques T = 30 kip-in. at its ends. Find i lie maximum shear, ion si le. and compressive stresses in the tube and their corresponding strains. Assume that G = 6000 ksi.
A circular tube AB is fixed at one end and free at the other. The tube is subjected to concentrated torques as shown in the figure. If the outer radius of the tube is 1.5 in, and the thickness is 3/4 in., calculate the strain energy stored in the tube. Let G= 11,800 ksi.
A tubular bar with outside diameterd2= 4.0 in, is twisted by torques T = 70,0 kip-in. (see figure). Under the action of these torques, the maximum tensile stress in the bar is found to be 6400 psi. Determine the inside diameter rtf of the bar. If the bar has length L = 48.0 in. and is made of aluminum with shear modulus G = 4,0 × 106 psi, what is the angle of twist d (in degrees) between the ends of the bar? (c) Determine the maximum shear strain y (in radians)?