A ring and disc are both rolling without slipping so that both have a kinetic energy of 108. What is the translational kinetic energy of the ring ? What is the translational kinetic energy of the disc ? 72.0 J Computer's answer now shown above. Incorrect. Submissions to practice problems are not permanently recorded. Tries 2/2 Previous Tries

A ring and disc are both rolling without slipping so that both have a kinetic energy of 108. What is the translational kinetic energy of the ring ? What is the translational kinetic energy of the disc ? 72.0 J Computer's answer now shown above. Incorrect. Submissions to practice problems are not permanently recorded. Tries 2/2 Previous Tries

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Sphere has mass of 10kg and radius of 10cm It’s spinning at 30 rads a second. It stops in 60 seconds due to constant torque applied. How much work is done by torque?
A 2.13-kg solid sphere (radius 0.135 m) is released from rest at the top of a ramp and allowed to roll without slipping. The ramp is 0.703 m high and 5.07 m long. When the sphere reaches the bottom of the ramp, what is its total kinetic energy? = Tries 0/6 Submit Answer What is its rotational kinetic energy? Submit Answer Tries 0/6 What is its translational kinetic energy?
The 5.0 kg, uniform, horizontal rod is seen from the side. What is the gravitational torque about the point shown? Use g = 10 m/s2. (Hint: It means the point shown is the pivot - rotational axis. Clearly draw the free-body diagram with the pivot, force, and r.) O O O C O OO 25 cm 12.5 N·m -12.5 N·m 25 N·m -25 N·m 75 N·m -75 N·m 50 N.m -50 N.m 0 none of the above 75 cm
1. A pulley has a constant angular acceleration of 3 rad/s?. When the angular velocity is 2rad/sec, that the total acceleration of a point on the rim of the pulley is 10ft/s?. Compute the diameter of the pulley.
10. A 240-N solid sphere that is 0.200-m in radius rolls 6.00-m down a ramp that is inclined at 37.0° with respect to the horizontal. (a) What is the angular speed of the sphere at the bottom of the ramp if it starts from rest? Answer: 35.5 rad/s
Arithmetic question. Write only the final value of the answer. Suppose you did the rotational dynamics labs with a 200g solid sphere. The sphere was placed at rest at the 100cm mark on the track which is inclined at 150 angle with the table. What is the translational kinetic energy in (J) of the sphere as it leaves 0 mark of the track? Write your answer with TWO decimal places.
5. A metal hoop with a diameter of 10 cm is released from rest on top of an inclined plane and rolls down the plane. What is the speed of the hoop when it reaches the end of the plane? 40 cm
A hollow, spherical shell with mass 2.00 kg rolls without slipping down a 39.0 degrees slope. a)Find the acceleration. b)Find the friction force. c)Find the minimum coefficient of static friction needed to prevent slipping.
A hollow, spherical shell with mass 3.00 kg rolls without slipping down a 35.0 degree slope. a) Find the acceleration. b) Find the friction force. c) Find the minimum coefficient of static friction needed to prevent slipping.
A potter's wheel is a thick stone of radius 0.5 m with mass 100kg. It freely rotates at 50 rpm (revolutions per minutes). Angular speed = 5.24 rad/sec. Kinetic energy of the wheel = 170.95 The potter press a wet rag against the rim and exert a radially inward force of 70 N. This can stop the wheel from spinning in 6 second. 1) Find the angular acceleration of the wheel when it is slowing down 2) Find the magnitude of the torque that stops the wheel 3) Find the friction created by the wet rag on the wheel. 4) Find the coefficient of kinetic friction between the wheel and the rag.
A 260-N sphere 0.20 m in radius rolls without slipping 6.0 m down a ramp that is inclined at 31° with the horizontal. What is the angular speed of the sphere at the bottom of the slope if it starts from rest? rad/s
5.) A spanner generates 7 N.m of torque. It has a length of 0.8m. Assume the Force is perpendicular to the wrench handle. a) how much Force is needed to generate this torque, given the length above? b) If the force value was kept the same, but the length was increased to 1.2m, how much torque is generated? Y