Two 200/400 V, transformers are operated in parallel to share a load of 500 kVA at 0.75 power factor leading. Transformers are rated as below: A: 300 kVA; 1.2% resistance and 6.3% reactance B: 400 kVA; 0.8% resistance and 2.4% reactance Find: (i) The load carried by each transformer, (ii) The load voltage if the primary voltage equal to the nominal input voltage, (iii) the current of each transformer.
Q: 1. A 100-kVA distribution transformer has a maximum efficiency of 98 % at 50 % full-load and unity…
A: Efficiency η=98% power factor cosϕ=1
Q: 8. The two winding transformer and the autotransformer of the circuit shown in Figure are ideal.…
A: In a transformer MMF remains same i.e, I1N1=I2N2 amd in auto transformer total current is the…
Q: The primary of a certain transformer, with and open-circuit secondary, takes 1A at a power factor of…
A: Given I2=50Apower factor ϕ0=0.4power factor ϕ2=0.8
Q: Q2. Consider the single-phase transformer circuit shown below. Transformer ratings and reactances…
A:
Q: Question 2. A linear transformer couples a load consisting of a 360 N R1 jwM R2 resistor in series…
A: Sol: Given data, R = 360, L = 0.25H The given circuit is the equivalent circuit of a single phase…
Q: A star connected load with real impedance ZL= 1-j1 Ohm per phase is connected to the secondary of a…
A: The given data about a three phase YNyn0 connected transformer is: Star connected load is connected…
Q: A 25 kVA, 2400/240-V, single phase transformer has an equivalent impedance referred to the primary…
A: Given- Power of a transformer= 25kVA voltage=2400/240-V core loss= 120 W power factor= 0.85…
Q: The maximum efficiency at Full-load and Unity power factor of a 1-phase, 25 kVA, 2000/1000V, 50Hz…
A: At maximum efficiency, iron loss = copper loss Output power at full load = kva rating * power factor…
Q: A 50 MVA, 11/132 kV three-phase, 50 Hz, generator transformer has guaranteed parameters as, load…
A:
Q: A single phase transformer takes 10 A on no load at p.f. of 0.2 lagging. The turns ratio is 4: 1…
A: We have a single phase transformer having, No-load current (I) = 10 A Power factor (Cos ϕ0) = 0.2…
Q: A 100kVA transformer has a maximum efficiency of 0.95 at 50% full load and unity power factor .…
A: Electrical machines can be either generator or motors. They can be either Ac machines or DC…
Q: The shown distribution network is to supply two factories A & B with load curves indicated. Assume…
A: Note: We are authorized to answer three subparts at a time, since you have not mentioned which part…
Q: a 100 kva, 1100/220 v, 50 hz, single-phase transformer has a leakage impedance of (0.1 +0.40) ohm…
A: Single Phase Transformer-A Single Phase Transformer is a power Transformer. It is made up of one…
Q: The parameters of the transformer equivalent circuit are given bellow, Primary winding turns =1150.…
A:
Q: A 40-kVA, 8000/230-V distribution transformer has an impedance referred to the primary of 18 + j80…
A: In this question we need to find a secondary voltage of the transformer.
Q: A) Two 1-phase transformers with equal turn ratio have impedances of (0.5 + j3) and (0.6+j10) with…
A: The parallel configuration of transformer in s distribution system or load driving application helps…
Q: Given a 10 KVA, 1200/180 V, 50 Hz single-phase transformer with an impedance Zp = 10+j20 Ohms…
A: To find the equivalent impedance when referred to secondary side of the transformer
Q: A 60HZ transformer having a 480 turn primary winding takes 80 W in power and 1.4 A in current at an…
A: No load power factor=power at noloadvoltage×current. EMF =4.44 frequency ×flux×primary turns.
Q: A 30 kVA, 2400/120V., 50Hz transformer has a high voltage winding resistance of 0.1Ω and a leakage…
A:
Q: 12. A 600 kVA, 1-ph transformer has an efficiency of 92 % both at full-load and half-load at unity…
A:
Q: The following results were obtained on a 50 kVA transformer. Open circuit test – primary voltage,…
A: TRANSFORMER: The transformer transfers power from one circuit to another circuit without a change…
Q: Practice Problem 1.3 A 100 kVA transformer 7,621/230 - Volt has primary and secondary resistances of…
A:
Q: Example 33.7. A 5,000-kVA, 3-phase transformer, 6.6/33-kV, NY, has a no-load loss of 15 kW and a…
A: Delta star connection of transformer- In case of the delta-star connection of a 3-phase…
Q: A 10kVA 2300/230V 60Hz, single phase transformer has Zp = 5.95 +13.8 ohms and Zs = 0.0595+j0.138…
A: The solution is given below
Q: 1. A 100-kVA distribution transformer has a maximum efficiency of 98 % at 50 % full-load and unity…
A: As per our company guidelines we are supposed to answer only first one question. Kindly repost other…
Q: A load of 200 kW at 0.85 power factor is to pe shared by two transformers A and B aving the same…
A:
Q: A 60 Hz ideal transformer is rated at 4800/240 V. A load with impedance Z,=12+ j9Q is connected…
A: for a transformer Turns ratio is primary turnssecondary turns=primary voltagesecondary voltage=…
Q: We can apply lamination to the primary winding of transformers to reduce the cross section of the…
A: In this question, Choose the correct option The given Statment is true or false?
Q: A A-A transformer bank consists of three individual transformers each with its rating given in the…
A: NOTE:" Since you have a posted a question with multiple sub parts, we will solve first three sub…
Q: The shown distribution network is to supply two factories A & B with load curves indicated. Assume…
A: given peak load of A=400KVApeak load of B=400KVApower factor=0.8
Q: The shown distribution network is to supply two factories A & B with load curves indicated. Assume…
A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you.…
Q: A single phase, 250 kVA, 10kV/2kV 60 Hz transformer has the following equivalent circuit parameters…
A: Given Single phase transformer 250 KVA,10 Kv/2Kv 60 HzRc(HV)=60.2 kΩ Xm(HV)=18.44…
Q: 6. A 5,000-kVA, 3-phase transformer, 6.6/33-kV, NY, has a no-load loss of 15 kV and a full-load loss…
A: In this question 3 phase transformer delta -star is given....We have to find out primary voltage…
Q: A transformer rated at a maximum of 25kVA supplies a 12kW load at power factor 0.60 lagging. a) What…
A: Transformer :- It transfers electric energy and changes voltage through the principle of…
Q: A 230/460-V transformer has a primary resistance of 0.2 ohms and reactance of 0.5 ohms and the…
A: Given: N1N2=230460R1=0.2 ΩX1=0.5 ΩR2=0.75 ΩX2=1.8 ΩI2=15 Acosϕ=0.6 pf lagging
Q: A 4800/240-V, single phase transformer is rated at 10 kVA. It has an equivalent impedance referred…
A:
Q: Two impedances Z, and Z2 are connected in series with the primary and secondary winding of an ideal…
A: Given circuit is - Given values are - XL1=j6OhmXL2=j9Ohmω=1000 Given that transformer is ideal.
Q: Given a 6 kVA , 600/120 -V, 60 Hz single phase transformer. The Transformer has primary coil…
A:
Q: 4. 100 kVA, 6800-240 V, 50 Hz single phase step down transformer has the following parameters:…
A:
Q: Q1. The equivalent resistance and equivalent reactance (high side) for a 37.5 kVA, 2400-600 V, 60 Hz…
A: Given transformer with37.5 KVA,2400/600 v,60 HzEquivalent resistance and reactance referred to…
Q: The efficiency of a 440/110V, 40kVA, single-phase transformer is 98.77% when delivering full-load at…
A: Single Phase Transformer: A single phase transformer is an electrical device that accepts…
Q: Q2. Consider the single-phase transformer circuit shown below. Transformer ratings and reactances…
A: We will use following formula of Zp.u to find Zpu on common on common base values Znew (P.u)=…
Q: A 40-kVA, 8000/230-V distribution transformer has an impedance referred to the primary of 18 + j80…
A:
Q: 8. The two winding transformer and the autotransformer of the circuit shown in Figure are ideal.…
A: given transformer and autotransformer
Q: Q/ A 600 kVA, 1-ph transformer has an efficiency of 92 % both at full-load and half-load at unity…
A: Given, A 600 KVA ,1-ph transformer has, Efficiency at full load and half load at is 92% and unity…
Q: II.) The number of turns on the primary and secondary windings of a single-phase transformer are 350…
A: Given: The number of turns on the primary and secondary windings of a single-phase transformer is…
Q: A single-phase ideal transformer is rated at 1OKVA, 240V/120V. Calculate the following: a. Rated…
A:
Q: 6- A 600 kVA, 1-ph transformer has an efficiency of 92 % both at full- load and half-load at unity…
A: In this question we need to find efficiency of transformer for given loading conditions.
Step by step
Solved in 4 steps with 4 images
- In per-unit equivalent circuits of practical three-phase transformers, under balanced thr-phase operation, in which of the following connect ions would a phase-shifting transformer come up? (a) Y-Y (b) Y- (c) -Three single-phase two-winding transformers, each rated 25MVA,54.2/5.42kV, are connected to form a three-phase Y- bank with a balanced Y-connected resistive load of 0.6 per phase on the low-voltage side. By choosing a base of 75 MVA (three phase) and 94 kV (line-to-line) for the high-voltage side of the transformer bank, specify the base quantities for the low-voltage side. Determine the per-unit resistance of the load on the base for the low-voltage side. Then determine the load resistance RL in ohms referred to the high-voltage side and the per-unit value of this load resistance on the chosen base.Three single-phase, two-winding transformers, each rated 450MVA,20kV/288.7kV, with leakage reactance Xeq=0.10perunit, are connected to form a three-phase bank. The high-voltage windings are connected in Y with a solidly grounded neutral. Draw the per-unit equivalent circuit if the low-voltage windings are connected (a) in with American standard phase shift or (b) in Y with an open neutral. Use the transformer ratings as base quantities. Winding resistances and exciting current are neglected.
- Consider a bank of this single-phase two-winding transformers whose high-voltage terminals are connected to a three-phase, 13.8-kV feeder. The low-voltage terminals are connected to a three-phase substation load rated 2.0 MVA and 2.5 kV. Determine the required voltage, current, and MVA ratings of both windings of each transformer, when the high-voltage/low- voltage windings are connected (a) Y-, (b) -Y, (c) Y-Y, and (d) -.The ideal transformer windings are eliminated from the per-unit equivalent circuit of a transformer. (a) True (b) FalseIn developing per-unit circuits of systems such as the one shown in Figure 3.10. when moving across a transformer, the voltage base is changed in proportion to the transformer voltage ratings. (a) True (b) False
- In developing per-unit equivalent circuits for three-phase transformers. under balanced three-phase operation. (i) A common Sbase is selected for both the H and X terminals. (ii) The ratio of the voltage bases Vbase/VbaseX is selected to be equal to the ratio of the rated line-to-line voltages VratedHLL/VratedXLL. (a) Only one of the above is true. (b) Neither is true. (C) Both statements are true.Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in , place the polarity marks, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a, b, and c such that VAN is 90 out of phase with Va for positive sequence.The ratings of a three-phase three-winding transformer are Primary(1): Y connected 66kV,15MVA Secondary (2): Y connected, 13.2kV,10MVA Tertiary (3): A connected, 2.3kV,5MVA Neglecting winding resistances and exciting current, the per-unit leakage reactances are X12=0.08 on a 15-MVA,66-kV base X13=0.10 on a 15-MVA,66-kV base X23=0.09 on a 10-MVA,13.2-kV base (a) Determine the per-unit reactances X1,X2,X3 of the equivalent circuit on a 15-MVA,66-kV base at the primary terminals. (b) Purely resistive loads of 7.5 MW at 13.2 kV and 5 MW at 2.3kV are connected to the secondary and tertiary sides of the transformer, respectively. Draw the per- unit impedance diagram, showing the per-unit impedances on a 15-MVA,66-kV base at the primary terminals.
- For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the rated voltage on the other winding? (a) Yes (b) NoConsider three ideal single-phase transformers (with a voltage gain of ) put together as three-phase bank as shown in Figure 3.35. Assuming positive-sequence voltages for Va,Vb, and Vc find Va,Vb, and VC. in terms of Va,Vb, and Vc, respectively. (a) Would such relationships hold for the line voltages as well? (b) Looking into the current relationships, express IaIb and Ic in terms of IaIb and Ic respectively. (C) Let S and S be the per-phase complex power output and input. respectively. Find S in terms of S.The direct electrical connection of the windings allows transient over voltages to pass through the auto transfonner more easily, and that is an important disadvantage of the autotransformer. (a) True (b) False