75 N.mC125 N.m2 m1mA steel shaft is fixed at A and is subjected to the torques as shown. Segment AB hasa diameter of 50 mm, segment BC has a diameter of 30 mm and G- 77 GPa.[1] Determine the internal torque in segment AB, show units.[2] Determine the internal torque in segment BC, show units.[3] Determine the angle of twist in degrees for segment AB, show units.

Given data: dAB=50 mmdBC=30 mmG=77 GPa Need to determine the torque in segment AB, BC and angle of…

Answered: 75 N.m C 125 N.m 2 m 1m A steel shaft…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For the shaft shown in the figure below, compute the angle of twist of pulleys B and C relative to A. The steel shaft has a diameter of 35 mm throughout its length. The torques are T1= 1500 N · m, T2 = 1000 N · m, = 500 N · m. The lengths are L, = 500 mm, L2 = 800 mm. T3 L2 T |T2 T3 A C B.
Determine the allowable torque a hollow steel shaft can transmit if the outside diameter is 4 inches, and the inside diameter is 3 inches. The allowable shear stress is 10,000 psi. Compute the angle of twist per foot of length. Answer = 85,900 in-lbs I'm unsure of how to solve this problem. Could you please help me solve for the answer step-by-step? Thank you in advance.
Two solid circular shafts are connected by two rigid gears. Note shaft ab is a composite shaft. Determine the angle of twist at point 'a' in degrees to two decimal places. solid shaft 60 in $= 11/1535 TL GJ J=TY/2r4 b composite shaft C 35 in bearing Notes:- gear b radius = 6.0 in - gear c radius = 4.0 in - shaft ab outer radius= 1.5 in - shaft ab inner radius= 1.1 in - shaft cd radius= 1.0 in - shaft ab inner shear modulus = 12000 ki - shaft ab outer shear modulus = 3000 ksi - shaft cd shear modulus = 12000 ksi outer portion inner portion shaft ab cross-section 2.86 in-kip
A circular steel shaft of diameter 30 mm is subjected to a torque of 60 N-m. Calculate the angle of twist if the length of the shaft is 20 m.
A shaft ABCD is fixed at end D and has torques acting at points A, B, and C as shown below. The bearing support between A and B allows free rotation. If we know that A = −0.382 rad, A/B = 0.358 rad, and B/C = −0.233 rad, calculate the absolute twist of the shaft at point C(oc) and enter it in rad (radians) correct to 3 significant digits below. Make sure to include the sign if it is negative noting that CCW rotations are positive and CW rotations are negative. 150 N.m 280 N.m B 40 N-m D
Answer the following problem. Show your complete solution. Use 4 decimal places. Calculate the diameter of the shaft required to transmit 45 kw at 120 rpm. The maximum torque is likely to exceed the mean by 30% for a maximum permissible shear stress of 55. Calculate also the angle of twist for a length of 2m.
Design the outside and inside diameters for a hollow stell shaft subjected to a torque of 1,000,000 in-lb. The maximum shear stress developed in the shaft is not to exceed 8,000 psi. The inside diameter is to be 2/3 of the outside diameter. Calculate the angle of twist in degrees for a 14 foot length of this shaft. Answer: D(outside) = 9.259 inches, D(inside) = 6.176 inches, angle of twist= 1.39 degrees I'm unsure of how to solve this problem. Could someone help me walk through the process step-by-step? Thanks in advance.
QUESTION 1 Figure Q1 shows a 1.4 m long steel shaft that consists of a hollow segment AB and a solid segment BC. The shaft is fixed at C and is subjected to two external torques TA and TB at points A and B, respectively. The torque developed at the fixed end C is 750 kN.m in the direction as indicated in Figure Q1. Given G=75 GPa. (a) Determine the values of TA and Tâ if the corresponding angle of twist of end A is zero. (b) Calculate the maximum shear stress developed in the shaft and locate where it's occurred (c) Give your comment whether the shaft will fail or not if the allowable shear stress of the shaft is 75 MPa. Ø0.4 m Ø0.32 m Section r-r 750 kN.m TB TA A 0.6 m 0.8 m Figure Q1
a) Figure Q5 shows a 1.4 m long steel shaft that consists of a hollow segment AB and a solid segment BC. The shaft is fixed at C and is subjected to two external torques TA and TB at points A and B, respectively. The torque developed at the fixed end C is 750 kN.m in the direction as indicated in the figure. i) Determine the values of TA and TB if the corresponding angle of twist of end A is zero. ii) Calculate the maximum shear stress developed in the shaft. Give your comment whether the shaft will fail or not if the allowable shear stress of the shaft is 75 MPa. 750 kN.m 1.4 m 0.8 m C 160 mm B Тв 200 mm- ΤΑ Section a-a Figure Q5 = [Ans: a) i) T 332 kN.m, TB=1082 kN.m, ii) TCB,max = 60 MPa, TBA,max=45 MPa]
1) The rotating solid steel shaft (Fig.1 a) is simply supported by bearings at points B and C and is driven by a gear (not shown) which meshes with the spur gear at D, which has a 150 mm pitch diameter. The force F from the drive gear acts at a pressure angle of 20°. The shaft transmits a torque to point “A" of TA = 300 N.m. There is a step at point "C" as shown in Fig.1 (b), assume that D/d ratio is 1,09 and fillet radius (r) is 2,5 mm. a) Find the stress concentrations at point "C" due to bending and shear loads (Initially assume d=50mm). If the shaft is machined from quenched and drawn steel with Sy= 420 MPa and Sut=560 MPa and b) using a factor of safety of 2.5, determine the minimum allowable diameter of the shaft at "C" based on a static yield analysis using the distortion energy (DE) theory. If the shaft with a diameter (d) of 32 mm is made of a brittle material with Suc = 420 MPa and c) Sut=360 MPa, determine the factor of safety of the shaft at "C" based on a static analysis…
What is the minimum diameter of a solid steel shaft that will not twist through more than 4o in a 9 m length when subjected to a torque of 11 kN.m ? if G = 83 GPa
Topic: FUNDAMENTAL CONCEPT OF STRAIN (statically indeterminate) and TORSION (circular shafts and thin-walled tubes). Problem: A shaft with a constant diameter of 2” is loaded by torques applied to gears attached to it as shown. Using G = 12 x 106 psi, determine the relative angle of twist (in degree) of gear A relative to gear D. Use 2 decimal places. Use the given sign convention for uniformity. Provide a torque diagram

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS