Pre-lab questions:Q1- What is the power factor?Q2- Calculate the power factor for the figure 1, where C= 15 nF.IntroductionFigure 1 shows a simple motor model consisting of a series RL network (The given values arenot realistic).C+ViLR2.2mH1000Motor Model310Figure 1+VoD

Answered: Image /qna-images/answer/ced3cc3a-a8db-4305-a148-2f88e4968605.jpg

Answered: Pre-lab questions: Q1- What is the…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Similar questions

A small electric vehicle is powered by a 96 .1 V battery and uses a series wound motor. It has a step-down chopper for forward drive and a step-up chopper for regenerative braking. The total armature resistance is 0.1 Q, and the armature voltage constant is 10 mV/A-rad/s. Descending a hill in regeneration mode the motor speed is 750 rev/min and the armature current is a constant average value of 80 A. Calculate the value of the duty cycle required and the .available braking power
Q9) Estimate the positon of the pointer in PMMC instrument if damping torque is absent? a. Pointer moves to full scale deflection b. Pointer does not come to rest position c. Pointer does not stop at the value of measurement d. Pointer does not move from zero
3LDC Motor or AC Servomotor 'Explain why a BLDC motor experiences no slip at all during acceleration. Some of BLDC motors don't have encoder. What is kind of applications that suitable with this type of motor? Explain why the encoder sensor is not required. Calculate motor efficiency for the following motor. a. b. C. AC Servomotor 3-14 kW 24 A 1500 RPM CONT. 20 Nm 200 V ins. F
80.5% O A series motor runs at (800 r.p.m) when the voltage is (400 V) and the current is (25 A). The armature resistance is (0.4 Q) and the series field resistance is (0.2 Q). Determine the resistance to be connected in series to reduce the speed to (600 r.p.m) with same current 3.85 O 4.25 2.85 O A shunt generator is running at 1000 rpm. If flux is reduced by half, then what is
The following information is given for a 300kW, 600V, long shunt compound DC generat or, shunt field resistance is 75 ohms, armature resistance 0.01, brush resistance is 0.011 ohrms, series field resistance is 0.012 ohms and the divert or resistance of 0.036 ohms.When the machine is delivering full load; a. Draw the circuit diagrarn b. Calculate the voltage and C Power generated by the armat ure.
A series motor runs at 800 rev/min when the voltage is 400V and the current is 25A. The armature resistance is 0.4 ohm and the series field resistance is 0.2 ohm. Determine the resistance to be connected in series to reduce the speed to 600 rev/min with the same current.
This simulation is starting synchronous motor for matlab 2012 I want to know how I can measure the power factor in this figure
Find the rolling force and its power. The weight of the car is 800 Kg The weight of each person is 75 Kg You may assume any missing parameters you need in the design appropriately (e.g., the rolling-resistance-power, air-resistance-power, the DC motor's parameters, ....etc)
Two gen. A and B operate in parallel. The station capacity of A is 50MW and that of B is 25MW. The full load speed regulation of station A is 3% and of B is 3.5%. Find the load sharing of 50MW between both the machine and the no load frequency is 50Hz. Don't use pen and copy.
Refer here for the specifications of the D400. a) What power output should you be able to supply from the 24V D400 at 15.4 m/s? b) If the wind drops to 2 m/s, what will the output power be? c) According to the performance graph what is the maximum power you can obtain from the 24V D400? There is a possibility of installing the turbine on top of a 20m high mast instead. Assuming that Zo=0.012, what would you expect the wind speed to be at that height? Use wind shear formula and assume Vref = 7.5 m/s at a height of Zref =10 m.
An electric motor with a mass of 42 kg, rated speed of 3760 rpm and unbalance of 0.002 kg.m must be mounted on an insulator to obtain a force transmissibility of 0.141. Determine the stiffness of the insulator. Consider zero damping.
estion 1 "A DC machine consists of 4-poles and operating at 1500 rpm. Its frequency of the induced emf in armature is determined as 50 Hz" O True O False S A Moving to another question will save this response. e IT:P AR

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning