Q3: A step-index multimode fibre with a 50 µm core diameter and 10 km distance is 6.731 designed to deliver a bandwidth-length product of 500 MHz.km. What are the intermodal dispersion and the numerical aperture at 0.88 µm. Use 1.46 for the refractive index of the fibre core.

Q3: A step-index multimode fibre with a 50 µm core diameter and 10 km distance is 6.731 designed to deliver a bandwidth-length product of 500 MHz.km. What are the intermodal dispersion and the numerical aperture at 0.88 µm. Use 1.46 for the refractive index of the fibre core.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

P 2.7a What will be the cutoff wavelength for dominant mode in rectangular waveguide whose length is 10 cm? (2)
Problem 4 to separate ITU channel 59 using a fiber Bragg grating (FBG) and an optical circulator. The FBG is made from a fiber with an effective index of refraction of the core of 1.48 at You are to implement a simple one-channel demultiplexer ITU channel 59. a.) Draw a diagram of the demultiplexer b.) Calculate the periodicity of the index of refraction modulation in the core of the FBG fiber
3.9 Explain what is meant by the critical bending radius for an optical fiber. A multimode graded index fiber has a refractive index at the core axis of 1.46 with a cladding refractive index of 1.45. The critical radius of curvature which allows large bending losses to occur is 84 um when the fiber is transmitting light of a particular wavelength. Determine the wavelength of the transmitted light. Ans: 0.86 µm
Estimate the optical loss due to Fresnel reflection at a fiber core from GaAs each of refractive indices 1.5 and 3.6 respectively. Calculate the optical power coupled into a step index fiber of 60 µm core diameter with a numerical aperture of 0.3 from a GaAs surface emitting LED with an emission diameter of 90 µm and a radiance of 50 W sr1cm-2. Determine the overall power conversion efficiency for the LED if it is operating with a drive current of 100 mA and a forward voltage of 1.6V.Find the optical output power and 3 dB optical modulation bandwidth for the LED if the device emits 400 µW of optical power into air when modulated at a frequency of 150 MHz with the minority carrier recombination lifetime of 7 ns.
apoint chanay of 30ncis located at th corigam) while plane yz3 carries fined 1Dat point (6,4,3) chavg to nc /m'
Figure: structure of a thin film silicon solar cell. Glass Front ITO i (aSi:H) back ZnO:AI 1-D PC The figure above shows a schematic overview of an thin film single junction solar cell. Upon what principle is the back reflector of this solar cell based? The principle of the back reflector is based on refractive scattering. ) The principle of the back reflector is based on diffractive scattering. ) The principle of the back reflector is based on constructive/destructive interference. The principle of the back reflector is based on plasmonic scattering
Consider a step index multimode fiber with a core diameter of (9.0000x10^1) (µm), a core refractive index of (1.48000x10^0) and a cladding refractive index of (1.38000x10^0). Suppose that we use a laser diode emitter at a wavelength of (1.570x10^0) (um) and a spectral FWHM linewidth of (2.00000x10^0) (nm) to transmit a rectangular profile pulse along this fiber. Calculate the bit-rate × distance product, BL, of this fiber in units of (bits km/s). Assume the intermodal dispersion dominates over any other dispersion for this fiber. Give your answer to 4 significant digits. Note: Your answer is assumed to be reduced to the highest power possible. Your Answer: x10 units Answer
A 2 V signal is incident to the interface from a 75 Ohm region propagating to a 50 Ohm impedance region. What is the reflection coefficient? What is value of the incident, reflected and transmitted wave? What voltage would you measure on either side of the interface right after the signal goes through the interface.
We have such fiber with length of 4 km and couple light from a single mode laser with center wavelength of 1337.4 nm with FWHM linewidth of 8.7 nm. Please calculate the pulse broadening (in ps) due to material dispersion!
14 A high-reflectance stack of alternating high-low index lay- ers is produced to operate at 2 um in the near infrared. A stack of four double layers is made of layers of germanium (n = 4.0) and MGF2 (n = 1.35), each of 0.5-um optical thickness. Assume a substrate index of 1.50 and normal in- cidence. What reflectance is produced at 2 um?
Determine NA and acceptance angle in air for silica optical fiber given the cladding refractive index (1.5) and core refractive index (1.57).
A single mode fibre is to be dimensioned. The normalised frequency is 80 % of the maximum allowed for single mode condition. The relative refractive index difference is 0.005 and the refractive index of the core is 1.5. The wavelength is 1.5 µm. A. Determine the radius of the core. B. If the number of modes supported by this fiber is 5. Determine the radius of the core.