Q8(): For the truss shown in theFigure, if the diameter of pins atA and G are 3 in and2 in,respectively. Both stresses in Aand70 kips 50 kipsA 4ftВ 4#C 4ftaredoubleshear.Determine the shear stresses in9 ftpins at A and G and the stressesmembers AG; AFmember GF if their diameter is 4inandin.

The stresses are to be calculated in support pin and members of truss. First the reaction forces are…

Q8(0: For the truss shown in the Figure, if the diameter of pins at A and G are 3 in and 2 in, respectively. Both stresses in A and Determine the shear stresses in 70 kips 50 kips A 4 ft B 4 ft C 4f are double shear. pins at A and G and the stresses 9 ft in members AG; AF and member GF if their diameter is 4 in. 夏

Q8(0: For the truss shown in the Figure, if the diameter of pins at A and G are 3 in and 2 in, respectively. Both stresses in A and Determine the shear stresses in 70 kips 50 kips A 4 ft B 4 ft C 4f are double shear. pins at A and G and the stresses 9 ft in members AG; AF and member GF if their diameter is 4 in. 夏

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.14P: The state of stress on an element along the hydraulic lift cylinder on a truck is trv= — 5 MPaLFind...

See similar textbooks

Similar questions

Repeat the previous problem using ? = 50° and stresses on the rotated element: sy1= 70 MPa, ??y1=-82 MPa, and tx1y1=-35 MPa.
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
Calculate the normal stresses at points A and B of the bracket caused by the 30-kN force.
100 kN and 200 kN to the rectangular column in the figureTwo forces act in intensity. A and B according to givenon the stress element by finding the stresses atshow.
Find the stresss in the left rod after its lower end is attached to the support.
2. The bar AC is supported by a pin at A and a cable that runs from B to E around the frictionless pully at D. If the allowable tensile stress oallow = 5.2 ksi for the cable, determine the required minimum diameter (inch) of the cable. The cylinder (connected at C) weighs 890 lb. Neglect weight and thickness of the bar AC. D 4 3 A C 5 ft 5 ft -4 ft 890 lb
The compound bar carries the axial forces P and 2P. Find the maximum allowable value of P (in lbs) if the working stresses are 40 ksi for steel and 20 ksi for aluminum, and the total elongation of the bar is not to exceed 0.2
In the figure, the nut is tightened by applying 450 N to a lug wrench. Show the stresses on the stress element by finding the stresses at one point according to the given
2. If the allowable shear stress for each of the steel pins at A and B is tpe 6.5 ksi and the allowable normal stress for bar CB is Operm 10 ksi, determine the diameter of the pins at A and B and that of the square bar CB. Pin A is in double shear while Pin B is in single shear. Ignore points D and E. (^ } 2.5 ft -3 ft -5 ft 150 lb/ft Fx =
A simple pin-connected truss is loaded and supported as shown. All members of the truss are aluminum pipes that have an outside diameter of 70 mm and a wall thickness of 3 mm. Determine the normal stress in each truss member. Assume P-12 kN, Q - 17 kN, a- 1.4 m, b -3.6 m, and c-1.3 m. Use positive for tensile stress and negative for compressive stress. Answers: OAB- JAC- OBC- i B (3) b MPa. MPa. MPa.
circular tube AB is fixed at one end andfree at the other end. The tube is subjected to axialforce at joint B. If the outer diameter of the tube is 75 mm and the thickness is 19 mm, calculate the max-imum normal stress in the tube.
Member AC is shown in Figure is subjected to a vertical force of 3 kN.Determine the position x of this force so that the average compressive stressat the smooth support C is equal to the average tensile stress in the tierod AB. The rod has a cross-sectional area of 400 mm2 and the contact areaat C is 650 mm2.