Iwo single-phase transformers whose phase electrical equivalent circuits are given below areconnected in parallel and 4 =0.+ j0.62 is feeding a worth of load. Idle operating voltage ofTransformer 1 is 220 V and Transformer 2 idle operating voltagę is 240V.transformer 1transformer 20.20w mmj0.92j0.900.200.252j0.80j0.820.2503.3k23.3k2 EV,a.) Find the currents flowing from transformers to the load.b.) Find the active powers that transformers transfer to the load.w ww m w w www w ww

Answered: Image /qna-images/answer/93cd86fd-5e4f-4f82-8b10-aa8eff3aac98.jpg

Two single-phase transformers whose phase electrical equivalent circuits are given below are connected in parallel and 2, =0.8+ j0.612 is feeding a worth of load. Idle operating voltage of Transformer 1 is 220 V and Transformer 2 idle operating voltage is 240V. transformer 1 transformer 2 0.20 J0.942 j0.91 0.20 0.250 j0.82 J0.82 0.250 3.342 1sson 3.34n a.) Find the currents flowing from transformers to the load. b.) Find the active powers that transformers transfer to the load.

Two single-phase transformers whose phase electrical equivalent circuits are given below are connected in parallel and 2, =0.8+ j0.612 is feeding a worth of load. Idle operating voltage of Transformer 1 is 220 V and Transformer 2 idle operating voltage is 240V. transformer 1 transformer 2 0.20 J0.942 j0.91 0.20 0.250 j0.82 J0.82 0.250 3.342 1sson 3.34n a.) Find the currents flowing from transformers to the load. b.) Find the active powers that transformers transfer to the load.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.33P: Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage...

See similar textbooks

Similar questions

In the system shown in Figure 1, the transformers are connected star-star with both star points grounded and the generators are connected in star with thier star points grounded. The system base is 15 MVA. The transformers all have reactances of 0.04 p.u. on this 15 MVA base. The reactances of all other elements are given in Table 1 (in 2) and the voltage levels are given in Table 2. p.u. G1 p.u. T1 jö Per-Unit Convert all values to p.u. on a 15 MVA base. Xa= p.u. Xc₂= XL = V BABE G1 2 X 9 T3 Figure 1: A section of the distribution system T1 L Table 1: Sequence reactances (2) 3 G1 L G2 0.3 0.59 0.01 4 L 9/10 10 Fault Voltage What is the voltage at bus 3 (in Volts) after the fault has occurred? Vp= V T2 5 T2 34 10/4 Table 2: Voltage bases (kV) G2 4 T3 10/9 | G2 Fault Current A three-phase fault with a fault reactance of 0.01 p.u. occurs at bus 3. Calculate the fault current flowing at the fault point in KA. Ip=-j KA So
Two 100-kW, single-phase transformers are connected in parallel both on the primary and secondary. One transformer has an ohmic drop of 0.5% at full-load and an inductive drop of 8% at full-load current. The other has an ohmic drop of 0.75% and an inductive drop of 2%. Show how they will share a load of 180 kW at 0.9 p.f.
The p.u. impedance value of an alternator corresponding to base values of 13.2 kV and 30 MVA is 0.2 p.u. Then the p.u. impedance value of an alternator for the new base values of 13.8 kV and 50 MVA is......
Connect three single-phase transformers in Y-Y, with subtractive polarity, so that the line-to-line voltages on the primary are 30 degrees delayed to their respective line-to-line voltages on the secondary. It should show each step that is needed to make this connection (example: the phasor diagram) and should show the final connection of the three transformers including the polarity markings. Assume phase A on the primary is terminal "H1".
What are the conditions for the parallel operation of 1-phase transformers?
a)Why are transformers generally connected in parallel at a substation?b)What conditions must be met for two transformers to be paralleled?c)Draw the phase relationship and connection diagram for Dd0 connection andYy6
Consider the three single-phase two-winding transformers shown in Figure. 3. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in A, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a', b', and c' such that VAN is 90° out of phase with V₂'b' for positive sequence. DI H₂ Figure. 3: Three-Winding Transformer
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator
Two 11,000/2,200-V, 1-phase transformers are connected in parallel to supply a total load of 200 at 0.8 p.f. lagging at 2,200 V. One transformer has an equivalent resistance of 0.4 ohms and equivalent reactance of 0.8 ohms referred to the low-voltage side. The other has equivalent resistance of 0.1 ohms and a reactance of 0.3 ohms. Determine the current and power supplied by each transformer.
Two 100-kW, single-phase transformers are connected in parallel both on the primary and secondary. One transformer has an ohmic drop of O.5% at full-load and an inductive drop of 8% at full-load current. The other has an ohmic drop of 0.75% and inductive drop of 2%. Show how they share a load of 180 kW at 0.9 power factor.
What effects are produced by change in voltage? 1. Iron los..........varies approximately as V². 2. Cu loss..........it also varies as V² but decreases with an increase in voltage if constant kVA output is assumed. 3. Efficiency...........for distribution transformers, efficiency at fractional loads decreases with in- crease in voltage while at full load or overload it increases with increase in voltage and vice- versa. 4. Regulation..........it varies as but decreases with increase in voltage if constant kVA output is assumed. 5. Heating.........for constant kVA output, iron temperatures increase whereas Cu temperatures decrease with increase in voltages and vice-versa.
7. TY Hat CHICL Ans. 1. Iron los.........varies approximately as V². 2. Cu loss..........it also varies as ² but decreases with an increase in voltage if constant kVA output is assumed. 3. Efficiency...........for distribution transformers, efficiency at fractional loads decreases with in- crease in voltage while at full load or overload it increases with increase in voltage and vice- versa. 4. Regulation..........it varies as but decreases with increase in voltage if constant kVA output is assumed. 5. Heating.........for constant kVA output, iron temperatures increase whereas Cu temperatures decrease with increase in voltages and vice-versa. quems