Refrigeration and Air Conditioning Technology (MindTap Course List)
8th Edition
ISBN: 9781305578296
Author: John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 16, Problem 12RQ
To determine
Advantages of direct digital controls.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Liquid-level control system shown in figure below. Explain principle of operation.
Which of the following is not used in automation of warehouse operations:
Select one:
Forklifts
Overhead trolleys
POS system.
Conveyor belts
5.A. If there's no adjusting valve at the outlet of a large pump, there should be a(n)A. aerator in the pump.B. orifice plate in the outlet.C. flow valve at the inlet.
5.B. A conveyor that uses a line shaft to turn the rollers should have the line shaft bearings checked on a PMinspection everyA. four weeks.B. six months.C. YEAR
5.C. You're going to install a new chain on a power transmission system. What else should you do with thissystem?A. Replace both sprocketsB. Check shaft bearings
D. Check the motor and gearbox
Chapter 16 Solutions
Refrigeration and Air Conditioning Technology (MindTap Course List)
Ch. 16 - True or False: Pneumatic controls are...Ch. 16 - Pneumatic controls are operated by A. water. B....Ch. 16 - One advantage of a modern control system is A....Ch. 16 - A control loop contains _______, _______, and...Ch. 16 - Pneumatic air must A. be clean and dry. B. have...Ch. 16 - The air supplied to a diaphragm is 20 psig, and...Ch. 16 - When a large volume of air is needed at a...Ch. 16 - Prob. 8RQCh. 16 - Prob. 9RQCh. 16 - An analog control signal A. has an infinite number...
Ch. 16 - Another term used to describe sensitivity in...Ch. 16 - Prob. 12RQCh. 16 - Prob. 13RQCh. 16 - One of the major components of a residential...Ch. 16 - Prob. 15RQCh. 16 - Describe a control device, and give three examples...Ch. 16 - Describe what a sensor does in a DDC system used...Ch. 16 - What is the difference between an active and a...Ch. 16 - A control system consists of what three basic...Ch. 16 - List six advantages that DDC control systems have...Ch. 16 - Describe the difference between the analog and...Ch. 16 - Describe the difference between an open-loop and a...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Microprocessor a. Doesn't need b. Need other chips to work O. contain all components d. Contains only processorarrow_forwardWhich of the following is the best example of an underdamped system? O A) A car door that once opened stays open until you close it. B) A wild west saloon door that swings back and forth until it eventually stops. O9A trap door that quickly slams shut once the trap is triggered. DJ A storm door on a house that when opened slowly closes again.arrow_forward16.a. What is the purpose of thermostat number 2, IN7, in the mixing vat machine?A. This thermostat is used to monitor the temperature of the incoming fluids.B. This thermostat is used to prevent an over-temperature condition in the event thermostat one sticks open.C. This thermostat is used to turn off the mixing motor after the mixture reaches temperature.D. This thermostat is used to shut off the heater when the chemical mix reaches setpoint. 16.b. After replacing a faulty CPU module, what is the next action you should take?A. Check the power supply service voltage.B. Issue a RUN or START command.C. Reprogram the user memory with ladder logic.D. Reset the watchdog timer.arrow_forward
- Select the simple system from the following. a. Air conditioner b. Closed loop room heating system c. Speed control of Motor d. Lamp with on/off switcharrow_forwardSelect the most accurate system from the following, O a. Lamp with on/off switch O b. Room heating system O c. Traffic light O d. Air conditionerarrow_forwardWhich of the following systems generate more energy when used in industrial applications? a. pneumatic systems b. hydraulic systems c. none of the listed d. both systems generate same energyarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage LearningUnderstanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
The Robot Revolution: The New Age of Manufacturing | Moving Upstream; Author: Wall Street Journal;https://www.youtube.com/watch?v=HX6M4QunVmA;License: Standard Youtube License