Concept explainers
The dynamic reaction at C and D after the couple has been removed.
Answer to Problem 18.101P
The dynamic reaction at C after the couple has been removed is
The dynamic reaction at D after the couple has been removed is
Explanation of Solution
Given information:
The weight (W) of the disk is 6 lb.
The radius (r) of the disk is 3 in..
The angular velocity
The angular velocity of shaft CBD and arm AB is
The horizontal distance (c) between the center of rod CBD and center of disk is 5 in..
The vertical distance (b) between the center of rod CBD and center of disk is 4 in..
The couple
The time (t) of couple applied is 2 s.
Calculation:
Find the mass (m) of the disk using the equation:
Here, g is the acceleration due to gravity.
Substitute 6 lb for W and
Write the equation of vector form of angular velocity
The angular velocity
Write the equation of angular velocity of disk A
Write the equation of angular velocity
Find the equation of angular velocity
Substitute 0 for
Find the equation of angular momentum about A
Substitute 0 for
Find the rate of change of angular momentum
Here,
Write the equation of the rate of change of angular momentum about A
Substitute
Write the equation mass moment of inertia
Write the equation mass moment of inertia
Write the equation of velocity of the mass center A of the disk.
Write the equation of acceleration of the mass center A of the disk.
Substitute
Find the position vector of D with respect to A.
Substitute 5 in. for c and 4 in. for b.
Find the rate of change of angular momentum about D
Substitute
Substitute
Sketch the free body diagram and kinetic diagram of the system as shown in Figure (1).
Refer Figure (1).
Apply Newton’s law of motion.
Substitute
Equate i-vector coefficients in Equation (3).
Equate k-vector coefficients in Equation (3).
Take moment about D.
Here,
The moment at D is equal to the rate of change of angular momentum at D.
Equate Equation (3) and (7).
Find the acceleration of shaft CBD and arm using equate the j- vector coefficients in Equation (8).
Substitute
After the 2 s, the couple
Find the angular velocity
Substitute 0 for
Find the component of dynamic reaction at C
Substitute 4 in. for b, 3 in. for r, 5 in. for c, and
Find the component of dynamic reaction at D
Substitute 4 in. for b, 3 in. for r, 5 in. for c, 14.18 rad/s for
Find the component of dynamic reaction at C
Substitute 4 in. for b, 3 in. for r, 60 rad/s for
Find the component of dynamic reaction at D
Substitute 4 in. for b, 3 in. for r, 60 rad/s for
Find the dynamic reactions at C using the equation:
Substitute
Thus, the dynamic reactions at C after the couple has been removed is
Find the dynamic reactions at D using the equation:
Substitute
Thus, the dynamic reactions at D after the couple has been removed is
Want to see more full solutions like this?
Chapter 18 Solutions
VECTOR MECH...,STAT.+DYN.(LL)-W/ACCESS
- An automobile wheel test rig consists of a uniform disk A, of mass mд = 5000 kg and radius rà = 1.5 m, that can rotate freely about its fixed center C and over which the wheel of an automobile is made to roll. A wheel B, whose center and center of mass coincide at D, is mounted on a shaft (not shown) that holds D fixed while it allows the wheel to rotate about D. The wheel has diameter d = 0.62 m, mass mß = 21.5 kg, and mass moment of inertia about its mass center /D = 44 kg.m². Both A and B are initially at rest when B is subject to a constant torque M that causes B to roll without slip on A. M BC B TA If M = 1200 N.m, use the angular impulse-momentum principle to determine how long it takes to reach conditions simulating a car speed of 100 km/h. The automobile wheel test rig takes 17.95 s to reach conditions simulating a car speed of 100 km/h.arrow_forwardA thin, homogeneous triangular plate of weight 10 lb is welded to a light, vertical axle supported by bearings at A and B. Knowing that the plate rotates at the constant rate w = 8 rad/s, determine the dynamic reactions at A and B.arrow_forwardA homogeneous disk of weight W = 6 lb rotates at the constant rate w1 = 16 rad/s with respect to arm ABC, which is welded to a shaft DCE rotating at the constant rate w2 = 8 rad/s. Determine the dynamic reactions at D and E.arrow_forward
- A 240-lb block is suspended from an inextensible cable which is wrapped around a drum of 1.25-ft radius rigidly attached to a flywheel. The drum and flywheel have a combined centroidal moment of intertia of 10.5 lb-ft-s^2. At the instant shown, the velocity of the block is 6 ft/s directed downward. The bearing at A as a frictional moment of 60 lb-ft. What is the kinetic energy of the system after the block moved after 4ft? (in ft-lb)arrow_forwardAn automobile wheel test rig consists of a uniform disk A, of mass mà = 5000 kg and radius rà = 1.5 m, that can rotate freely about its fixed center C and over which the wheel of an automobile is made to roll. A wheel B, whose center and center of mass coincide at D, is mounted on a shaft (not shown) that holds D fixed while it allows the wheel to rotate about D. The wheel has diameter d = 0.62 m, mass mß = 21.5 kg, and mass moment of inertia about its mass center /D = 44 kg-m². Both A and B are initially at rest when B is subject to a constant torque M that causes B to roll without slip on A. M B d A If M = 1200 N·m, use the angular impulse-momentum principle to determine how long it takes to reach conditions simulating a car speed of 100 km/h. The automobile wheel test rig takes s to reach conditions simulating a car speed of 100 km/h.arrow_forwardThe blade of an oscillating fan and the rotor of its motor have a total mass of 300 g and a combined radius of gyration of 75 mm. They are supported by bearings at A and B, 125 mm apart, and rotate at the rate w1 = 1800 rpm. Determine the dynamic reactions at A and B when the motor casing has an angular velocity w2 = (0.6 rad/s)j.arrow_forward
- QI/ A shaft rotating at 120 r.p.m is supported in bearing A and B, 1.8 m apart, A being at the left – hand end. Two unbalanced rotating masses of 7.5 kg and 10 kg at radii of 75 mm and 50 mm respectively are situated between A and B at distances of 0.6 m and 0.9 m respectively from A. The angle between the radii is 60º when viewed along the shaft. Answer the following questions: and ... 1- The dynamic forces are 2- Forces on bearings A and B due to dead weight are and 3- Resultant force at A and B are ..... and 4- A rotor supported at A and B carries two masses. The rotor is (a) dynamically balanced (b) statically balanced (c) both (a)&(b) (d) none. 5- The static balancing is satisfactory for low-speed rotors but with increasing speeds, dynamic balancing becomes necessary. This is because, the (a) unbalanced couples are caused only at higher speeds (b) unbalanced forces are not dangerous at higher speeds (c) effects of unbalances are proportional to the square of the speed (d) effects…arrow_forwardA shaft turning at a uniform speed carries two uniform discs A and B of masses 10kg and 8kg respectively. The centres of the mass of the discs are each 2.5mm from the axis of rotation. The radii to the centres of mass are at right angles. The shaft is carried in bearings C and D between A and B such that AC = 0.3m, AD = 0.9m and AB = 1.2m. It is required to make dynamic loading on the bearings equal and a minimum for any given shaft speed by adding a mass at a radius 25mm in a plane E. Determine: The dynamic loading on each bearing when the mass in plane E has been attached and the shaft rotates at 200 rev/min. For the bearing loads in the opposite direction determine all the unknown values. For the bearing loads in the same direction, show the diagrams and equations only to use for a possible solution. PS – Use graphical methods to solve the balancing problemarrow_forwardA shaft turning at a uniform speed carries two uniform discs A and B of masses 10kg and 8kg respectively. The centres of the mass of the discs are each 2.5mm from the axis of rotation. The radii to the centres of mass are at right angles. The shaft is carried in bearings C and D between A and B such that AC = 0.3m, AD = 0.9m and AB = 1.2m. It is required to make dynamic loading on the bearings equal and a minimum for any given shaft speed by adding a mass at a radius 25mm in a plane E. Determine: The magnitude of the mass in plane E and its angular position relative to the mass in plane A The distance of the plane E from plane A PS – Use graphical methods to solve the balancing problemarrow_forward
- A shaft turning at a uniform speed carries two uniform discs A and B of masses 10kg and 8kg respectively. The centres of the mass of the discs are each 2.5mm from the axis of rotation. The radii to the centres of mass are at right angles. The shaft is carried in bearings C and D between A and B such that AC = 0.3m, AD = 0.9m and AB = 1.2m. It is required to make dynamic loading on the bearings equal and a minimum for any given shaft speed by adding a mass at a radius 25mm in a plane E. Determine: (a) The magnitude of the mass in plane E and its angular position relative to the mass in plane A (b) The distance of the plane E from plane A (c) The dynamic loading on each bearing when the mass in plane E has been attached and the shaft rotates at 200 rev/min. For the bearing loads in the opposite direction determine all the unknown values. For the bearing loads in the same direction, show the diagrams and equations only to use for a possible solution.arrow_forwardA shaft turning at a uniform speed carries two uniform discs A and B of masses 10kg and 8kg respectively. The centres of the mass of the discs are each 2.5mm from the axis of rotation. The radii to the centres of mass are at right angles. The shaft is carried in bearings C and D between A and B such that AC = 0.3m, AD = 0.9m and AB = 1.2m. It is required to make dynamic loading on the bearings equal and a minimum for any given shaft speed by adding a mass at a radius 25mm in a plane E. Determine: (a) The magnitude of the mass in plane E and its angular position relative to the mass in plane (b) The distance of the plane E from plane A (c) The dynamic loading on each bearing when the mass in plane E has been attached and the shaft rotates at 200 rev/min. For the bearing loads in the opposite direction determine all the unknown values. For the bearing loads in the same direction, show the diagrams and equations only to use for a possible solution. PS - Use graphical methods to solve the…arrow_forwardA shaft turning at a uniform speed carries two uniform discs A and B of masses 10kg and 8kg respectively. The centres of the mass of the discs are each 2.5mm from the axis of rotation. The radii to the centres of mass are at right angles. The shaft is carried in bearings C and D between A and B such that AC = 0.3m, AD = 0.9m and AB = 1.2m. It is required to make dynamic loading on the bearings equal and a minimum for any given shaft speed by adding a mass at a radius 25mm in a plane E. Determine: The magnitude of the mass in plane E and its angular position relative to the mass in plane A The distance of the plane E from plane A The dynamic loading on each bearing when the mass in plane E has been attached and the shaft rotates at 200 rev/min. For the bearing loads in the opposite direction determine all the unknown values. For the bearing loads in the same direction, show the diagrams and equations only to use for a possible solution. PS – Use graphical methods to solve the…arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY