Refrigeration and Air Conditioning Technology (MindTap Course List)
8th Edition
ISBN: 9781305578296
Author: John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 22, Problem 5RQ
After heat is absorbed into a condenser medium in a water-cooled condenser, the heat can be deposited in one of two places. What are they?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
How to do a heat/energy balance on a anode fuel cell and a condenser given that the fuel cell is isothermal and the outlet of the condenser is 25 degrees?
O Falge
QUESTION 2
The refrigerant undergoes a change of phase during the heat-transfer process, the pressure of the retrigerant is the saturation
pressure during the low supply and low rejection processes.
True
False
QUESTION 3
Frequently, the vapor of the liquid leaving the condenser is lower than the saturation temperature.
O True
False
QUESTION &
The pressure of the iquid leaveng the condenser we be less than the pressure of the vapor entarng, wd etempernd
the retigerant in the condenser.
O Te
QUESTION S
Are many situations in which it is desirable to combine three cycles in series, either power systems or refigertion sytems, to
take advantage of a very wide temperature range or to utilize what would otherwise be waste heat to improve etficiency
O true
O False
QUESTION 6
A cycle can't be made very efficient, since the temperature differences between the two fluid streams can be controlled
through careful design of the combined system.
True
(b)
Bathroom sinks and some other fixtures include an overflow opening in the basin. This
opening is located on the wall and near the top of the basin. The overflow opening
serves two important functions:
If the water tap is left on while the drain stopper is closed, the opening will
channel water down into the drain opening rather than letting is spill out of the
sink onto the floor.
The overflow allows the sink to drain faster by introducing air into the system.
A sink with a dimension given in Figure Q2(b), has water flows into it at a rate of
8 L/min. If the drain stopper is closed and water level in the sink remains constant,
determine the average velocity of water flows through the 3.0 cm diameter overflow
hole.
Front
3 cm diameter
overflow holes
Q-8 L/min
15 3/4| 40 cm
15 cm
Side
(a)
Figure Q2: (a) Picture of the sink; (b) Sink dimension
(Ь)
Chapter 22 Solutions
Refrigeration and Air Conditioning Technology (MindTap Course List)
Ch. 22 - Why do some condensers have to be cleaned with...Ch. 22 - The three materials of which condensers are...Ch. 22 - Who should be consulted when condenser cleaning is...Ch. 22 - When is the most heat removed from the refrigerant...Ch. 22 - After heat is absorbed into a condenser medium in...Ch. 22 - A water-cooling tower capacity is governed by what...Ch. 22 - When a standard-efficiency air-cooled condenser is...Ch. 22 - Four methods for controlling head pressure in an...Ch. 22 - The prevailing winds can affect which of the...Ch. 22 - True or False: Air-cooled condensers are much more...
Ch. 22 - The type of condenser that has the lowest...Ch. 22 - Compare the standard conditions of high-efficiency...Ch. 22 - Name two ways in which the heat from an air-cooled...Ch. 22 - Briefly describe what is meant by floating head...Ch. 22 - Explain how to flush impurities from a...Ch. 22 - Explain the basic operation of a combination ORI...Ch. 22 - Name two problems a refrigeration system may have...Ch. 22 - Briefly explain what is meant by condenser...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Why do some condensers have to be cleaned with brushes and others with chemicals?arrow_forwardIn a surface condenser, O cooling water and steam passes over the tubes. steam and cooling water never mix to give condensate. steam and cooling water mix to give condensate O steam and cooling water passes inside the tubes .arrow_forwardWhat are the advantages and limitations of surface condensers over jet condensers?arrow_forward
- Number 3 The food storage room requires a cooling system with a capacity of 15 tons of refrigeration that operates at an evaporator temperature of -17.5 ° C and a condenser temperature of 37.0 ° C. The refrigerant used is R-134a and the system operates in saturated conditions. a. COP= b.Refrigerant flow rate = Answer in kg / s. c. Heat loss rate in condenser = Answer kJ / s.arrow_forwardDraw the schematic and p-h diagram for the problem below: A two-stage cascade refrigeration system uses ammonia as the working substance. The evaporator is at -35 degree Celsius and high pressure condenser is at 1514.2 kPa. The cascade condenser is a direct-contact type. The refrigeration load is 90 tons. Determine the a.) the COP, and b.) the quantity of the fluid entering.arrow_forward3. The food storage room requires a cooling system with a capacity of 15 tons of refrigeration that operates at an evaporator temperature of -17.5 ° C and a condenser temperature of 40.7 ° C. The refrigerant used is R-134a and the system operates in saturated conditions. a. COP = Answer b. Refrigerant flow rate = Answer kg / s. c. Heat loss rate in condenser = Answer kJ / s.arrow_forward
- 2- The following data relate to a two-pass surface condenser: Steam condensed = 1540 kg/hr Temperature of cooling water when it enters the condenser = 15° C Temperature of cooling water when it leaves the condenser = 30 ° C Vacuum in the condenser = 675 mm of Hg Barometer reading = 750 mm of Hg Temperature of condensate = 32 ° C Quality of exhaust steam = 0.92 Water velocity in tubes = 2.6 m/s Outside diameter of tubes = 2.8 cm Thickness of tubes = 0.03 cm Heat Transfer coefficient = 3.35 kJ/h/cm Determine Area of the tube surface required а- b- No. of tubes c- Length of tubesarrow_forwardPlease calculate enthalpies and the heat of a condenser and evaporator. Thank youarrow_forwardWhat are the four stage of refrigeration Draw schematic diagram and explain each processarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage LearningWelding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
The Refrigeration Cycle Explained - The Four Major Components; Author: HVAC Know It All;https://www.youtube.com/watch?v=zfciSvOZDUY;License: Standard YouTube License, CC-BY